Abstract:One of the most critical aspects in understanding the deformation behavior of two-phase titanium alloys subjected to thermomechanical processes (TMPs) lies in being able to describe the flow stress accurately. To this end, in this study, initially, hot tension tests were conducted on a two-phase Ti-6Al-2Zr-1Mo-1V alloy. It was observed that the flow stress at a given temperature and strain rate exhibits work hardening, followed by flow softening. Flow softening occurs at the peak strain, where the maximum stress is observed; peak strain decreases with increasing temperature and decreasing strain rate. Variations in peak strain are more obvious at low temperatures and high strain rates. Later, the microstructure of the alloy was analyzed and the results show that work hardening and flow softening are caused by dynamic recrystallization (DRX). The DRX volume fraction was found to exhibit an increasing trend and discontinuous dynamic recrystallization (DDRX) was observed at increasing temperature and decreasing strain rate. With respect to microstructure evolution, a unified model consisting of a thermally activated stress component and an athermal stress component was developed. In the athermal stress term, dislocation density and the Hall-Petch effect were used to describe the work-hardening and flow-softening behavior. In the case of the dislocation term, the DRX effects were modeled considering the critical strain for DRX initiation and the DRX rate, which are both temperature-and strain rate-dependent. In the Hall-Petch effect term, the dependence of the Hall-Petch coefficient on the processing conditions was considered and the loss of Hall-Petch strengthening with deformation was modeled. Using the proposed model, the work-hardening and flow-softening behavior and microstructure evolution in Ti-6Al-2Zr-1Mo-1V alloys subjected to TMP were predicted. A good agreement could be observed between the experimental and predicted results. This study provides a solution for modeling work-hardening and flow-softening behavior and helps us understand the deformation behavior of two-phase titanium alloys subjected to TMP.

On the Modeling of Diffusion-Controlled Growth of Primary Alpha in Heat Treatment of Two-Phase Ti-alloys

Precipitation of Secondary Alpha in Competition with Epitaxial Growth of Primary Alpha in Two-Phase Titanium Alloys

Coupled Effects of Deformation and Cooling on the Evolution of Primary and Secondary Alpha of Two-Phase Ti-alloys

Assessment of Alpha Phase Evolution in Deformation of Two-Phase Ti-alloys under the Off-Equilibrium Condition

Microstructural Modeling of the Α + Β Phase in Ti-6Al-4V: A Diffusion-Based Approach

Achieving Fine-Grained Equiaxed Alpha Via Thermo-Mechanical Loading under Off-Equilibrium State in Two-Phase Ti-alloys

Study of PrimaryαPhase Transformation in a New Beta Titanium Alloy with Different Cooling Conditions

Cooling Rate Effects on Microstructure and Diffusion Behaviour in Ti65 Alloy: Insights from a Modified Diffusion Model

Effect of Cooling Rate on Microstructure Evolution During Α/β Heat Treatment of TA15 Titanium Alloy

Thermo-kinetic Modeling for the Growth/Dissolution of Globes and Lamella in Ti-55531 Under Continuous Heating Condition

Unified Modeling of Work Hardening and Flow Softening in Two-Phase Titanium Alloys Considering Microstructure Evolution in Thermomechanical Processes

Modeling and Simulation of Microstructure Evolution during Heat Treatment of Titanium Alloys

Numerical Simulation of Microstructure Evolution During the Solid Phase Transformation of Ti-6al-4v Alloy in Investment Casting

Modeling of the Precipitation Kinetics and Morphology Evolution of Lamellar Α in Ti-alloys During Non-Isothermal Treatments

Austenite Growth Behavior and Prediction Modeling of Ti Microalloyed Steel

Coarsening Kinetics and Morphological Evolution in a Two-Phase Titanium Alloy During Heat Treatment

Analysis of Globularization Modeling and Mechanisms of Alpha/beta Titanium Alloy

Effect of Α Morphology on the Diffusional Β ↔ Α Transformation in Ti–55531 During Continuous Heating: Dissection by Dilatometer Test, Microstructure Observation and Calculation

Ternary diffusion coefficients—Theoretical treatment and application to the <i>In-situ</i> -reinforced TiB<sub>2</sub>/Al composite

Microstructural Evolution During Post-Heat Treatment and Its Effect on the Mechanical Properties of Directed Energy Deposited Near Β Titanium Alloy

Orderly Nucleation and Competitive Growth Behaviors of Ti-Al Intermetallic Compounds in Ti/TiAl3 Diffusion Couple under High Temperature