Abstract:Highlights • A special-shaped C sf /AZ91D composite part with a high fiber volume fraction of 23.0% was firstly prepared by the LSEVI process. • The desired configuration features were directly formed, in the way of near-net forming. • The excellent microstructure with sufficient infiltration and no fiber aggregation was obtained. • Compared with the AZ91D, the compressive strength of the composite part was effectively increased by ∼40%. To meet the increased demand for light-weight and high-performance special-shaped load bearing parts in automotive industry, the short carbon fiber reinforced magnesium matrix composite (C sf /Mg) part with complex configuration features and abrupt cross-sectional transitions was fabricated by liquid-solid extrusion following vacuum pressure infiltration process (LSEVI). Near-net forming schemes of both the special-shaped fiber preform and composite part were proposed. The effect of process parameters on the forming quality of the composite part was discussed. Meanwhile, the microstructures and compressive properties in different regions of the part were analyzed. The results show that the forward forming scheme provides the special-shaped fiber preform with no surface defects. For the C sf /AZ91D part, its internal microstructures show that the infiltration of liquid magnesium is sufficient and uniform. The compressive strength of the composite part can reach up to 487 MPa, corresponding to ∼40% increase compared to 335 MPa of the AZ91D alloy. The average compressive strain of composites is less than 10%, which is about 50% of that of the AZ91D alloy. When the fiber orientation is parallel to the shear direction on the shear plane, the load-bearing capacity of the fiber is much higher than that of the fiber perpendicular to the shear direction. This work not only provides a convenient approach to fabricate special-shaped preform with high fiber volume fraction, but also gives a demonstration for the near-net forming of C sf /Mg parts with excellent material isotropy and compressive properties. Graphical abstract Download : Download high-res image (275KB) Download : Download full-size image

Design and Application of Forming Device for the Thin-Walled C-F/Mg Composite Component

Effect of fabrication parameters on carbon fibre reinforced magnesium matrix composite components

Recent research and development on forming for large magnesium alloy components with high mechanical properties

Development of AZ91D Magnesium Alloy-Graphene Nanoplatelets Composites Using Thixomolding Process

Preparation of the high compressive performance special-shaped C sf /AZ91D composite part using the liquid-solid extrusion following vacuum pressure infiltration process

An analysis of the factors affecting strengthening in carbon fiber reinforced magnesium composites

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Study on warm forming process of rigid-flexible composite drawing based on numerical simulation

An Investigation into the Forming of Fiber Metal Laminates with Different Thickness Metal Skins Using Hydromechanical Deep Drawing

Designing a magnesium alloy with high strength and high formability

Forming Technique of Magnesium Alloy Parts Produced by Liquid Combination Process of Die Casting and Forging

Experimental and simulation research on hollow AZ31 magnesium alloy three-channel joint by hot extrusion forming with sand mandrel

Forming Metal Components Through a Novel Fused-Coating Based Additive Manufacturing

Review on forming process of magnesium alloy characteristic forgings

Magnesium Alloy Characteristics and Developments of Its Plastic Forming Technology

Experimental and numerical study of thermoforming of Al/CFRP hybrid composites

Tensile and fatigue behavior of carbon fiber reinforced magnesium composite fabricated by liquid-solid extrusion following vacuum pressure infiltration

Deformation Characteristics and Microstructure Analysis of Aluminum Alloy Component with Complex Shape by Cold Orbital Forming

Development of a Thin-Wall Magnesium Automotive Door Inner Panel

Deep drawing of fiber metal laminates using an innovative material design and manufacturing process

Additive Manufacturing of Magnesium and its alloys: Process-Formability-Microstructure-Performance Relationship and Underlying Mechanism