Abstract:For the purpose of reducing weight of steel parts, save raw materials and keep or even improve safety standards, the development of advanced high strength steels is increasingly demanded in the automotive industry and engineering applications. We have proposed a novel heat treatment (quenching-partitioning-austempering treatment, Q-P-A) to obtain steel parts with high strength and good ductility. The Q-P-A process is intended to produce microstructure consisted of carbon-depleted martensite, carbon-enriched retained austenite and nanostructured bainite. Quenching(Q) treatment fabricates mixed microstructure of carbon-supersaturated martensite and certain amounts of untransformed austenite. Partitioning(P) thermal treatment accomplishes fully diffusing of carbon from the supersaturated martensite phase to the untransformed austenite phase and enriching the amount of carbon in untransformed austenite. Further low-temperature austempering(A) process induces incredible thin bainite from the carbon-enriched untransformed austenite. A study of the microstructure and mechanical properties of 50SiMnNiNb steel subjected to the novel Q-P-A treatment is presented. Microstructure is assessed by optical microscope(OM), field emission scanning electron microscope(FESEM) and transmission electron microscope(TEM), and the corresponding mechanical properties are measured. The experimental results indicate that attractive mechanical properties of steels during the Q-P-A process are attributed to the complex multi-phase structure. Slender plates of bainite with 20-40 nm thick are generated in the medium carbon steel. Meanwhile, with increasing of the volume fraction of nanostructured bainite, yield strength of steel parts is increased with little degradation of ultimate tensile strength. In this paper, a novel quenching-partitioning-austempering heat treatment is proposed, and the attractive mechanical properties of steels are obtained during the Q-P-A process.

Notably improved mechanical properties via introducing a short austempering treatment on low-carbon martensite steel

Strengthening and Toughening Mechanism of a Cu-bearing High-Strength Low-Alloy Steel with Refined Tempered Martensite/bainite (M/B) Matrix and Minor Inter-Critical Ferrite

Effects of Novel Q-P-T and Traditional Q-T Processes on the Microstructure and Mechanical Properties of Martensitic Steels with Different Carbon Content

Tailoring Low‐Alloyed Cryogenic Steel Strong and Tough Introduces Fine‐Grained Equiaxed Ferrite by Intercritical Subquenching

Transformation-Induced Ductility of Reverse Austenite Evolved by Low-Temperature Tempering of Martensite

A Carbide-Free Bainite/martensite/austenite Triplex Steel with Enhanced Mechanical Properties Treated by a Novel Quenching–partitioning–tempering Process

Microstructure and Mechanical Properties of 50simnninb Steel by A Novel Quenching-Partitioning-Austempering Heat Treatment

Study on the Mechanism of Excellent Strength and Toughness Combination of a High Nitrogen Martensitic Stainless Steel Treated by Q-C-P-T Process

Grain Refinement and Toughening of Low Carbon Low Alloy Martensitic Steel with Yield Strength 900 MPa Grade by Ausforming

A novel microstructural design and heat treatment technique based on gradient control of carbon partitioning between austenite and martensite for high strength steels

Novel Ultrahigh-Strength Nanolath Martensitic Steel by Quenching–partitioning–tempering Process

Enhancement of the Strength and Ductility of Martensitic Steels by Carbon

Effect of Intercritical Austenitizing Temperature during Quenching–Intercritical Quenching–Tempering Process on Toughness of 25Mn2Si2Cr Bainitic Steel

Advancement of strength and toughness in ultra-low carbon martensitic stainless steel by reversed austenite

Below- Ms austempering to obtain refined bainitic structure and enhanced mechanical properties in low-C high-Si/Al steels

Enhancement of the mechanical properties of a Nb-microalloyed advanced high-strength steel treated by quenching–partitioning–tempering process

Simultaneously Improved Strength and Impact Toughness by Introducing Ultrafine Ferrite in Low-Temperature Bainitic Steel

Dominating Role of Film‐Like Carbon‐Enriched Austenite for the Simultaneous Improvement of Strength and Toughness in Low‐Carbon Steel

Strengthening and toughening mechanisms of quenching–partitioning–tempering (Q–P–T) steels

Effect of Partitioning Treatment on the Mechanical Property of Fe-0.19c-1.47mn-1.50si Steel with Refined Martensitic Microstructure

Introducing ultrafine ferrite in low-temperature bainitic steel through a novel process for simultaneously improving strength and toughness