Abstract:Hybrid electric vehicle (HEV) and plug-in hybrid electric vehicle (PHEV) require high power energy sources which are inexpensive and safe. Among various battery materials, 5V LiMn1.5Ni0.5O4 spinel materials are especially of interests for these vehicle applications because of their high operating voltage of ~4.7V and because manganese is inexpensive and less toxic than Ni and Co. However, the cycle life of these cathodes is inadequate and elevated temperature cycling cause rapid loss of capacity of the LiMn1.5Ni0.5O4 cells. This capacity degradation can be attributed to dissolution of Mn and Ni elements, solid electrolyte interphase (SEI) formation and electrolyte decomposition with high-voltage cycling [1]. Metal oxide coatings, which are usually synthesized by solution-based coating techniques, have improved capacity retention of the LiMn1.5Ni0.5O4 cells at the elevated temperatures and have been usually synthesized by solution-based coating techniques [2,3]. Recently, we have successfully coated nanometer thick amorphous lithium phosphorus oxyntirde (Lipon) electrolytes on the surfaces of LiMn1.5Ni0.5O4 and LiCoO2 particles by a RFmagnetron sputtering technique [4,5]. Uniform subnanometer thick Lipon improved the cycling behaviors of LiMn1.5Ni0.5O4 cells dramatically, but did not impede the Mn dissolution. Although a thicker Lipon layers of a few nanometers were effective in preventing the Mn dissolution, the Lipon layers greatly reduced the specific capacity because Lipon has a very low electronic conductivity of ~10 -14 S/cm. For comparison, nanometerthick protective films of electronic/ionic mixed conductor are being evaluated. Half-cell performances of cathodes fabricated with LiMn1.5Ni0.5O4 particles coated with mixed conductor will be reported for cycling at room and

Surface Design with Spinel Limn1.5ni0.5o4 for Improving Electrochemical Properties of Lini0.5co0.2mn0.3o2 at High Cut-Off Voltage

Cycling Stability of 5V LiMn1.5Ni0.5O4 Spinel Particles Coated with a Thin Film Mixed Conductor

Surface Modification Mechanism of Spinel Structure LiM_xMn_(2-x)O_4 As Cathode Materials for Lithium Ion Batteries

Enhanced electrochemical performances of 5 v spinel LiMn 1.58Ni0.42O4 cathode materials by coating with LiAlO2

Enhanced Electrochemical Performance of Li1.2Mn0.54Ni0.13Co0.13O2 Cathode Material Coated with Li+-conductive Li2SiO3 for Lithium Ion Batteries

Binding Li 3 PO 4 to Spinel LiNi 0.5 Mn 1.5 O 4 via a Surface Co‐Containing Bridging Layer to Improve the Electrochemical Performance

Structure and Electrochemical Performance of Modificated LiMn<sub>2</sub>O<sub>4</sub> by S-Co Codoping and Nano SiO<sub>2</sub> Surface Coating

Structure and Electrochemical Performance of Modificated LiMn2O4 by S-Co Codoping and Nano SiO2 Surface Coating

Surface Modification of High Voltage Spinel LiNi 0.5 Mn 1.5 O 4 Cathode Material Manufactured via Co-precipitation

Improved Electrochemical Performance of 5 V Spinel LiNi 0 . 5 Mn 1 . 5 O 4 Microspheres by F-doping and Li 4 SiO 4 Coating

Enhanced Cycling Performance of Spinel LiNi0.5Mn1.5O4 Cathodes through Mg-Mn Hetero-Valent Doping via Microwave Sol-Gel Method

Surface Modification and Characterization of Spinel LiMn2O4 Coated with MgO

Improving rate capacity and cycling performance of lithium-rich high-Mn Li-1.8[Mn0.7Co0.15Ni0.15]O-2.675 cathode materials by Li2SiO3 coating

Performance Improvement of Li-rich Layer-Structured Li1.2Mn0.54Ni0.13Co0.13O2 by Integration with Spinel LiNi0.5Mn1.5O4

Conformal Coating of a High-Voltage Spinel to Stabilize LiCoO2 at 4.6 V

Enhanced Electrochemical Performance of Li1.2mn0.54ni0.13co0.13o2 Cathode with an Ionic Conductive Livo3 Coating Layer

Surface Coating with Li-Ti-O to Improve the Electrochemical Performance of Ni-rich Cathode Material

Surface Modification of Li1.03mn1.97o4 Spinels for Improved Capacity Retention

Suppressing the Structure Deterioration of Ni-Rich LiNi0.8Co0.1Mn0.1O2 Through Atom-Scale Interfacial Integration of Self-Forming Hierarchical Spinel Layer with Ni Gradient Concentration

Surface spinel reconstruction to suppress detrimental phase transition for stable LiNi0.8Co0.1Mn0.1O2 cathodes

Improved Cycle Stability of High-Capacity Ni-rich LiNi0.8Mn0.1Co0.1O2 at High Cut-off Voltage by Li2SiO3 Coating