Abstract:Improved mechanical properties of ferritic stainless steels (FSSs), such as toughness and high temperature or creep resistance, have been attained through the addition of stabilizing elements such as Nb and/or Ti. Therefore, stabilized ferritic stainless steels are good candidates to replace the conventional Cr-Ni austenitic stainless steels for specific applications to save the higher price of Ni. As compared to austenitic stainless steels, however, ferritic stainless steels possess lower formability which is closely depends on the gamma-fiber recrystallization texture. Hence, improvement of formability is desired for further wide applications of FSSs. The stabilizing effects of alloying elements work by consuming not only the interstitial atoms in solid solution but also forming the carbide and nitride precipitates such as TiC. TiN and NbC. The precipitation takes place in steel making processes such as slab reheating, hot rolling and coiling. The parameters involving these processes have their effects on the size, shape and distribution of the precipitates that influence the gamma-fiber recrystallization texture. Many papers intended to clarify the effect of precipitates. However, there were differences concerning the effect of precipitates, which may hinder further improvement of formability. In the present paper, precipitate size and dispersion were changed by controlling hot rolling processes and the effect of precipitate size and dispersion on the development of recrystallizaton texture in a 17%Cr ferritic stainless steels was investigated. Mechanical properties were measured by tensile tests. The characteristics of precipitate were observed by transmission electron microscopy, and X-ray diffraction was used to characterize texture evolution processes. The results show that low temperature finish rolling promotes the formation of a large number of fine and dispersed TiC precipitates in the hot band. After rolling and annealing, the state of fine and dispersed precipitation can be inherited in the cold rolled and annealed sheets. Strong gamma-fiber recrystallizaton texture is developed in the specimen with sparsely distributed and coarse precipitates. Fine and dispersed precipitates promote the nucleation of randomly oriented grains, strongly suppress the growth of recrystallized grain, and thereby weakening gamma-fiber recrystallizaton texture and impairing the formability of the cold rolled and annealed sheets. The precipitates have significant effects on the nucleation of randomly oriented grains and pinning grain boundary mobility during recrystallization annealing after cold rolling, which plays an important roles in controlling the gamma-fiber recrystallizaton texture in a ferritic stainless steels.

The Nature of Nano-Sized Precipitates in Ferritic/martensitic Steel P92 Produced by Thermomechanical Treatment

Precipitate phases in ferritic/martensitic steel P92 after thermomechanical treatment

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Nano‐sized Precipitates in 11 % Cr Ferritic‐martensitic Steel after Thermomechanical Treatment

Evolution of Precipitates in Thermomechanically Strengthened P92 Steel under Fe Ion Irradiation at 400 °C

Fe Ion Irradiation Effects on the Precipitates of P92 Steel after Thermomechanical Treatment

Precipitate Phases in Normalized Ferritic/Martensitic Steel P92

Effect of Thermo-Mechanical Treatment on Microstructure and Mechanical Properties of P92 Heat Resistant Steel

Evolution of Precipitate Phases in Ferritic and Martensitic Steel P92 During Normalizing and Tempering

Thermal stability of nanocrystalline microstructure in P92 heat resisting steels

Characterization of Precipitates in X12CrMoWVNbN10-1-1 Steel During Heat Treatment

Textures and Precipitates in A 17%cr Ferritic Stainless Steels

Investigation on Microstructural Evolutions and Mechanical Properties of P92 Steel During Thermal Processing

Identification of irradiation-induced phases in thermomechanically strengthened P92 steel after Fe ion irradiation at 700°C

Precipitate Phase Evolution in a 11cr Ferritic/Martensitic Steel During Tempering

Nanoprecipitation-suppressed Ferrite Transformation (γ → Α) During Tempering in a Medium‑manganese Steel

Effect of Surface Mechanical Attrition Treatment on Microstructure and Oxidation Behavior in T91 Steel at High Temperature

Precipitate Formations with Self-Adaptive Elemental Diffusion and Segregation in T92 Steel

Precipitates Change of P92 Steel under 3.5 MeV Fe13+ Ion Irradiation at 400 °C

Grain Boundary Engineering for Enhancing Intergranular Damage Resistance of Ferritic/martensitic Steel P92

Importance of cold rolling and tempering on the microstructure evolution, precipitation behavior and mechanical responses of 9Cr3Co3W1Cu ferritic/martensitic steel