Abstract:In this paper, aluminium chloride crystal was used as precursor to prepare silica-alumina aerogel support by sol gel method, and the active component K2CO3 was supported on the aerogel support by incipient-wetness impregnation method to obtain a modified potassium-based adsorbent. CO2 adsorption experiment was performed on the adsorbent under different reaction conditions using a small fixed-bed reactor self designed. Based on the characterization results of low temperature N-2 adsorption-desorption experiments and scanning electron microscopy, CO2 adsorption characteristics of modified potassium-based adsorbents were studied. The prepared silica-alumina aerogel support has good microstructure and uniform pores with specific surface area and pore volume are 445.7517 m(2)/g and 2.3270 cm(3)/g, respectively, and the mesopores account for more than 99%. After loading, the active component K2CO3 is uniformly dispersed. Through model comparison, it was determined that the shrinking core model and Avrami fractional kinetic model were used to fit the experimental results in order to study the reaction kinetics and adsorption kinetics. The results show that as the temperature rises, the amount of CO2 adsorbed by the adsorbent increases first and then decreases. The increase in temperature can improve the activity of the active site of the adsorbent and make the reversible exothermic reaction occur while the adsorbent adsorbs CO2 cannot proceed in the forward direction at the same time. According to the kinetic analysis, the control period of the surface chemical reaction is too short due to the high temperature, which caused low carbonation conversion. The optimal designed loading of modified potassium-based adsorbent, reaction temperature, water vapor pretreatment time, CO2 concentration and total gas volume were 30%, 60 degrees C, 30 min, 12.5%, and 500 mL/min, respectively.

Adsorption Separation of Co2/Ch4 Gas Mixture on Carbon Molecular Sieves Modified by Potassium Carbonate

Thermodynamic–Kinetic Synergistic Separation for O 2 /N 2 and CO 2 /CH 4 on Nanoporous Carbon Molecular Sieves

A High-Permeance Supported Carbon Molecular Sieve Membrane Fabricated by Plasma-Enhanced Chemical Vapor Deposition Followed by Carbonization for Co2 Capture

Preparation and characterization of activated carbon modified by potassium for carbon dioxide/methane adsorption and separation

Grand canonical Monte Carlo simulation of methane–carbon dioxide mixtures on ordered mesoporous carbon CMK-1

Adsorption separation of CO_2 from flue gas by hyperbranched solid-amine

Oxygen-enriched Carbon Molecular Sieve Hollow Fiber Membrane for Efficient CO2 Removal from Natural Gas

Computer Simulation of Adsorption and Separation of CO2/CH4 in Modified COF-102

The experimental research of cryogenic adsorption separation of CH_4/N_2 on carbon molecular sieve(CMS)

Application of Modified Carbon Molecular Sieves for Air Separation Based on Adsorption Kinetics

Adsorption of Pure and Binary Co2, Ch4, and N-2 Gas Components on Activated Carbon Beads

Gas separation performance of supported carbon molecular sieve membranes based on soluble polybenzimidazole

Enrichment of Oxygen-Containing Low-Concentration Coalbed Methane with CMS-3KT as the Adsorbent

Experimental investigation of CO2 separation by adsorption methods in natural gas purification

Molecular Insights into Adsorption and Diffusion Properties of CO2/CH4 in Cation-Exchanged ZSM-5 Zeolites

High-performance carbonized ZIF-8-doped hybrid carbon molecular sieve membrane for CO2/N2 separation

Study on CO2 Capture Performance by Potassium-Promoted MgAl-Hydrotalcite Adsorbent

Grand canonical Monte Carlo simulation of the adsorption and separation of carbon dioxide and methane using functionalized Mg-MOF-74

High-Performance Carbon Molecular Sieve Membrane Derived from a Crown Ether-Containing Co-Polyimide Precursor for Gas Separation

PSA separation of CH 4/N 2 mixture with carbon molecular sieve

Experiment and Kinetic Model Study on Modified Potassium-Based CO2 Adsorbent