Abstract:The effect of rolling temperature on the incomplete recrystallization behavior and the relationship to mechanical properties in 0.06C–4Mn-1.2Cr (wt.%) steel was investigated. Three plates of experimental steel were produced by hot rolling at different temperatures and intercritical annealing processes in this study. The microstructure of experimental steels was examined by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The mechanical properties of test steel were examined by impact test and tensile test. Austenite reversion and cementite precipitation-dissolution was numerically simulated under the assumption of local equilibrium. With the decrease of hot rolling temperature from 1000 °C to 800 °C, the uniform equiaxed prior austenite grains microstructures changed to heterogeneous microstructures of laminated and ultrafine prior austenite grains arranged alternatively. The tensile and impact tests revealed that the medium manganese steels rolling at 800 °C had an excellent combination of mechanical properties. Elongation had a great relationship with retained austenite fraction and stability. The fractography of impact specimens was examined to explore the toughening mechanism of the micro-laminated steels. The steel with uniform equiaxed grain structure exhibited a relatively low tensile strength of 750 MPa and low elongation of ∼20% and an extremely poor low-temperature toughness of ∼40 J at −40 °C. An enhanced low-temperature toughness (∼233 J at −40 °C), as well as an improved tensile strength (823 MPa) and higher elongation of ∼40%, was obtained in the steel with heterogeneous microstructures. The content of austenite in heterogeneous microstructure is twice that in uniform equiaxed grain structure. And cementite dissolved more thoroughly in the heterogeneous microstructure. The high austenite content of heterogeneous microstructures enabled the steel to be significantly stronger and ductile, which contributed to the high tensile strength and elongation to some extent. It is concluded that the effect of interface decohesion resulted in the occurrence of delamination. And the high austenite content and delamination greatly improved the low-temperature toughness of experimental steel.

The effect of warm deforming and reversal austenization on the microstructure and mechanical properties of a microalloyed steel

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

The Impact of Annealing Temperature on the Microstructure - Properties Relationship of Reversion-Induced Austenitic Stainless Steels

Effects of Deformation Temperature in Austenite Recrystallization Region on Grain Refinement of Microalloyed Steels

Interplay Between Reversed Austenite and Plastic Deformation in A Directly Quenched and Intercritically Annealed 0.04C-5Mn Low-Al Steel

Study of Retained Austenite and Nano-Scale Precipitation and Their Effects on Properties of a Low Alloyed Multi-Phase Steel by the Two-Step Intercritical Treatment

Evolution of Microstructure and Crystallographic Texture of Microalloyed Steel During Warm Rolling in Dual Phase Region and Their Influence on Mechanical Properties

Effect of Hot Deformation Parameter on Grain Refinement of Austenite Through Recrystallization with Α→γ Reverse Transformation

Microstructural Evolution and Microstructure–Mechanical Property Correlation in Nano/ultrafine-Grained Fe-17Cr-6Ni Austenitic Steel

Effect of rolling temperature on microstructure and mechanical properties of medium manganese steel

Stability of Retained Austenite in Multi-Phase Microstructure During Austempering and Its Effect on the Ductility of a Low Carbon Steel

Effect of Deformed Prior Austenite Characteristics on Reverse Phase Transformation and Deformation Behavior of High-Strength Medium-Mn Steel

Effects of Different Austenitising Conditions on the Strength–Ductility Balance in a High-Strength Low-Alloy Steel

Refinement Technology of Austenite Grains

Influence of annealing temperature on microstructure, tensile properties and tensile deformation mechanism of metastable austenitic stainless steel repetitively cold-rolled and annealed

Recrystallization behavior in a low-density high-Mn high-Al austenitic steel undergone thin strip casting process

Effect of Prior Austenite Grain Size on Austenite Reversion, Bainite Transformation and Mechanical Properties of Fe-2Mn-0.2C Steel

The Effect of Annealing on the Microstructural Evolution and Mechanical Properties in Phase Reversed 316LN Austenitic Stainless Steel

Effect of Heterogeneous Microstructure on Refining Austenite Grain Size in Low Alloy Heavy-Gage Plate

The Effect of Reversed Austenite on Mechanical Properties of 13cr4nimo Steel: a CPFEM Study

Enhanced Tensile Properties of a Reversion Annealed 6.5Mn-Trip Alloy Via Tailoring Initial Microstructure and Cold Rolling Reduction