Abstract:The ever increasing demand for safe and lightweight steel has promoted the development of advanced high-strength steel (AHSS). Recently, many AHSSs have been developed through chemical heterogeneity, resulting in microstructure refinement and mechanical property optimization. Although many efforts emphasize the construction of Mn-heterogeneous high-temperature austenite (gamma-Fe), the influence of Mn-heterogeneous distribution remains unclear. In this work, different austenitization times and temperatures are applied to Mn-partitioned pearlite, followed by the same quenching and partitioning process. The effect of Mn distribution in high-temperature austenite on the microstructural evolution and mechanical properties is systematically investigated. Results show that the Mn-heterogeneous high-temperature austenite can tailor the austenite-to-martensite transformation during quenching. The Mndepleted austenite is then readily transformed into lath martensite, and the Mn-enriched austenite is mainly retained as film roughness (RA), both of which assemble the ghost pearlite. With an increase in austenitization time and temperature, the Mn atom diffusion from the Mn-enriched austenite (originated from cementite lamellae) to the Mn-depleted one (originated from ferrite lamellae) increases, leading to the decreased chemical heterogeneity in high-temperature austenite. Thus, the fraction of ghost pearlite decreases while the fraction and size of blocky RA and coarse lath martensite increase. A wider lath martensite lowers the strength of the yield or the elastic limit of steel. The increased fraction and size of blocky RA ensure an increased uniform elongation by transformation-induced plasticity effect, whereas the transformation product (i. e., fresh martensite) is detrimental to the post-uniform elongation. Meanwhile, because the fractions of RA and martensite hardly change with austenitization condition, the ultimate tensile strength (about 1700 MPa) and total elongation (about 20%) are relatively constant. Therefore, tuning the Mn distribution in high-temperature austenite provides an effective strategy to tailor yield strength and uniform elongation while maintaining large ultimate tensile strength and total elongation.

Effect of Heterogeneous Microstructure on Refining Austenite Grain Size in Low Alloy Heavy-Gage Plate

A Novel Way Refining the Partially Reverted Globular Austenite in Reversion from Martensite

New Insights from Crystallography into the Effect of Refining Prior Austenite Grain Size on Transformation Phenomenon and Consequent Mechanical Properties of Ultra-High Strength Low Alloy Steel

The effect of warm deforming and reversal austenization on the microstructure and mechanical properties of a microalloyed steel

The Effects of Prior Austenite Grain Refinement on Strength and Toughness of High-Strength Low-Alloy Steel

Effect of Rapid Heating and Quenching on Microstructure and Mechanical Properties of High Strength Low Alloy Steel

Austenite Grain Ultrarefinement and the Formation of Nanocrystallized Structure through Transformation of Low Carbon Steels

Effect of Abnormal Grain Refinement on Synchronous Strengthening Behavior of Fe50Mn30Co10Cr10 High Entropy Alloys

Effects of Different Austenitising Conditions on the Strength–Ductility Balance in a High-Strength Low-Alloy Steel

Shaping mechanism of ultrafine metastable austenite in HSLA steels through a cumulative process of hot rolling, partitioning and tempering

Effect of Hot Deformation Parameter on Grain Refinement of Austenite Through Recrystallization with Α→γ Reverse Transformation

Refinement Technology of Austenite Grains

Effect of Mn Heterogeneous Distribution on Microstructures and Mechanical Properties of Quenching and Partitioning Steels

Optimization of Melt Treatment for Austenitic Steel Grain Refinement

Interplay Between Reversed Austenite and Plastic Deformation in A Directly Quenched and Intercritically Annealed 0.04C-5Mn Low-Al Steel

Effect of Prior Austenite Grain Size on Austenite Reversion, Bainite Transformation and Mechanical Properties of Fe-2Mn-0.2C Steel

Evolution Of Austenite Grain Size In Continuously Cast Slab During Hot-Core Heavy Reduction Rolling Process Based On Hot Compression Tests

Determining role of heterogeneous microstructure in lowering yield ratio and enhancing impact toughness in high-strength low-alloy steel

Refined heterogeneous phase unit enhances ductility in quenched ultra-high strength steels

Tuning Heterogeneous Microstructure and Improving Mechanical Properties of Twin-Roll Strip Cast Low Carbon Steels by On-Line Heat Treatments

The Effect of Network Cementite Dissolution on the Nucleation and Growth of Prior Austenite Grains in High Carbon Low Alloy Steels