Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Non-Monotonic Molecular Weight Dependence Of Crystallization Rates Of Linear And Cyclic Poly(Epsilon-Caprolactone)S In A Wide Temperature Range

Effect of Crystallization Temperature on Crystal Modifications and Crystallization Kinetics of Poly(l‐lactide)

Polymorphous Crystallization And Multiple Melting Behavior Of Poly(L-Lactide): Molecular Weight Dependence

Crystallization Behavior and Mechanical Properties of Poly(Epsilon-Caprolactone)/Cyclodextrin Biodegradable Composites

Crystallization kinetics and crystalline structure of biodegradable Poly(ethylene adipate)

Comparing Crystallization Rates Between Linear and Cyclic Poly(epsilon-Caprolactones) Via Fast-Scan Chip-Calorimeter Measurements

Effect of Molecular Weight on the Crystallization and Melt Memory of Poly(ε-caprolactone) (PCL)

Studies on Nonisothermal Crystallization of Ultra–high Molecular Weight Polyethylene in Liquid Paraffin

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Effect of Molecular Weight on Spherulitic Growth Rate of Poly(ϵ‐caprolactone) and Poly(ϵ‐caprolactone)‐b‐poly(ethylene Glycol)

The role of entanglement in crystallization and melting of cyclic poly(ε-caprolactone)s

Solution Crystallization Behavior Of Crystalline-Crystalline Dibloek Copolymers Of Poly(Ethylene Oxide)-Block-Poly(Epsilon-Caprolactone)

Effect of Molecular Weight on Isothermal Crystallization Kinetics of Multi-Walled Carbon Nanotubes-Graft-poly(ε-caprolactone)

Melt Crystallization And Morphology Of Poly(Epsilon-Caprolactone)-Poly(Ethylene Glycol) Diblock Copolymers With Different Compositions And Molecular Weights

Non-Isothermal Crystallization Kinetics of Poly (ɛ-Caprolactone) (PCL) and MgO Incorporated PCL Nanofibers

Isothermal Crystallization of Random Copolymers of Ε-Caprolactone with 2,2-Dimethyltrimethylene Carbonate

The nonisothermal crystallization kinetics of poly(α-chloromethyl-α-methyl-β-propiolactone)

Melt Crystallization and Morphology of Poly(ε‐caprolactone)‐poly(ethylene Glycol) Diblock Copolymers with Different Compositions and Molecular Weights

Crystallization Behavior Of Poly(Epsilon-Caprolactone)/Layered Double Hydroxide Nanocomposites

Confined Nucleation and Crystallization Kinetics in Lamellar Crystalline–Amorphous Diblock Copolymer Poly(ε-caprolactone)-b-poly(4-vinylpyridine)

Thermal and Crystalline Properties of Random Copolymer of CL and DTC Prepared by La(OAr)3