Abstract:The paper presents an analysis of the effective use of a mixture of steel sludge (S1) and slag (S2) from the converter process of steel production for the production of cement mortars. Metallurgical waste used in the research, which is currently deposited in waste landfills and heaps near plants, posing a threat to groundwater (possibility of leaching metal ions present in the waste), was used as a substitute for natural sand in the range of 0-20% by weight of cement (each). The obtained test results and their numerical analysis made it possible to determine the conditions for replacing part of the sand in cement mortars with a mixture of sludge and slag from a basic oxygen furnace (BOF) and to determine the effects of such modification. For the numerical analysis, a full quadratic Response Surface Model (RSM) was utilized for two controlled factors. This model was subsequently optimized through backward stepwise regression, ensuring the inclusion of only statistically significant components and verifying the consistency of residual distribution with the normal distribution (tested via Ryan-Joiner's test, p > 0.1). The designated material models are helpful in designing ecological cement mortars using difficult-to-recycle waste (i.e., sludge and converter slag), which is important for a circular economy. Mortars modified with a mixture of metallurgical waste (up to 20% each) are characterized by a slightly lower consistency, compressive and flexural strength, and water absorption. However, they show a lower decrease in mechanical strength after the freezing-thawing process (frost resistance) compared to control mortars. Mortars modified with metallurgical waste do not have a negative impact on the environment in terms of leaching heavy metal ions. The use of a mixture of sludge and steel slag in the amount of 40% (slag/sludge in a 20/20 ratio) allows you to save 200 kg of sand when producing 1 m3 of cement mortar (cost reduction by approx. EUR 5.1/Mg) and will also reduce the costs of the environmental fee for depositing waste.

Ecocement made of cement kiln dust and granular furnace slag

A New Kind of Eco-Cement Made of Cement Kiln Dust and Granular Blast Furnace Slag

Understanding the Role of Calcium Silicate Slag in Sodium Carbonate-Activated Green Materials: Influence on Kinetics, Strength, and Efflorescence

Hydration Characteristics of Cement Kiln Dust as Cementitions Materials

Pozzolanic Reactivity of the Synthetic Slag from Municipal Solid Waste Incinerator Cyclone Ash and Scrubber Ash

Synergistic Activation Mechanism and Long-Term Properties of a Solid Waste Cementitious Materials Based on Red Mud and Calcium Carbide Slag

Sustainable clinker-free solid waste binder produced from wet-ground granulated blast-furnace slag, phosphogypsum and carbide slag

Combination of Slag and Fly Ash to Prepare Engineered Cementitious Composite: A Study on Mechanical Properties and Gas Permeability

Study on the Alkali–Sulfur Co-Activation and Mechanical Properties of Low-Carbon Cementitious Composite Materials Based on Electrolytic Manganese Residue, Carbide Slag, and Granulated Blast-Furnace Slag

Utilization of carbide slag-granulated blast furnace slag system by wet grinding as low carbon cementitious materials

Characterization and Comparison of the Grindability, Residual Compressive Strength, and Hydrated Phases of Traditional Cement Prepared from Lime Rock and Carbide Slag

Synthesis and Characterization of Cement Clinker Using Waste Glass and Oyster Shells as Natural Ore Substitutes

Mechanical properties and chemical microscopic characteristics of all-solid-waste composite cementitious materials prepared from phosphogypsum and granulated blast furnace slag

Greener phosphogypsum-based all-solid-waste cementitious binder with steel slag activation: Hydration, mechanical properties and durability

Study on hydration process of CKD-GBFS Eco-cement by XRD

The Application of Converter Sludge and Slag to Produce Ecological Cement Mortars

Dynamic Mechanical Properties and Microstructure of Ultrafine Slag Powder Cement Paste Utilizing Solid Waste Industrial Tailings Powder and Fly Ash

Application of molten iron desulfurization slag to replace steel slag as an alkaline component in solid waste-based cementitious materials

Deep insight into mechanical behavior and microstructure mechanism of quicklime-activated ground granulated blast-furnace slag pastes

Preparation and Hydration Mechanisms of Low Carbon Ferrochrome Slag-Granulated Blast Furnace Slag Composite Cementitious Materials

Utilization of ground granulated blast-furnace slag and electrolytic manganese residue as a low-carbon cementitious material