Abstract:<p>Engineered cementitious composites (ECC) are widely used owing to their high tensile capacity and strain-hardening behavior; however, the use of large quantities of cement require huge amount of resources and pollutes the environment. Fly ash-based geopolymer has been considered as a promising alternative for the development of high-ductility eco-friendly engineered materials. To improve the tensile capacity of engineered geopolymer composites (EGC), an ultra-high-ductility engineered geopolymer composite has been developed with the incorporation of functionalized multi-walled carbon nanotubes and polyvinyl alcohol fiber. This paper reports the mixture process and mechanical tests on EGC with different mixtures. Fourier transform infrared spectroscopy (FT-IR) and X-ray powder diffraction were used to investigate the characteristics of the reaction products in the geopolymer matrix. The microscopic morphology of the geopolymer matrix were characterized using field emission scanning electron microscopy. The excellent saturated multiple cracking properties and strain hardening of the ultra-high EGC (UHEGCs) were demonstrated by uniaxial tension testing. At the maximum limit, the residual crack width and crack spacing of UHEGCs were generally less than 70 μm and 2 mm, respectively. Tensile strain-hardening behavior with an ultimate tensile strain greater than 8% was experimentally demonstrated for the UHEGC. Meanwhile, the compressive strength of the UHEGC was greater than 45 MPa. The pseudo-strain hardening (PSH) indexes of UHEGC were used to determine the tensile capacity formation. Analysis demonstrated that the tensile capacity of UHEGC can be quantified using the classic PSH criterion, whereas ultra-high crack-bridging capacity was attributed to the ultra-high-ductility of UHEGC. The XRD studies demonstrated that for the reaction products of the geopolymer matrix, new crystalline phases are insignificant. The FT-IR analyses revealed that the amorphous aluminosilicate phases were mainly reaction products, i.e., N-A-S-H. Most importantly, the multi-scale (micro- and meso-scale) modification mechanisms of the material through the addition of two fibers were revealed.</p>

Combination of Slag and Fly Ash to Prepare Engineered Cementitious Composite: A Study on Mechanical Properties and Gas Permeability

Use of Slag to Improve Mechanical Properties of Engineered Cementitious Composites (eccs) with High Volumes of Fly Ash

Eco-Friendly, High-Ductility Slag/Fly-Ash-Based Engineered Cementitious Composite (ECC) Reinforced with PE Fibers

Mechanical Properties and Carbonation Durability of Engineered Cementitious Composites Reinforced by Polypropylene and Hydrophilic Polyvinyl Alcohol Fibers

A multi-scale experimental investigation of the feasibility of using integrated coal gasification combined slag as a supplementary cementitious material

Preparation and mechanical characterization of engineered cementitious composites with high-volume fly ash and waste glass powder

Properties of modified engineered geopolymer composites incorporating multi-walled carbon Nanotubes(MWCNTs) and granulated blast furnace Slag(GBFS)

Evaluation of compressive strength and chloride permeability of cement-based materials with high-volume compound mineral admixtures

Properties of High-Content Micro-Steel Fiber Self-Compacting Concrete Incorporating Fly Ash and Slag Powder Performance Study

Utilization of Corn Cob Ash as Fine Aggregate and Ground Granulated Blast Furnace Slag as Cementitious Material in Concrete

Engineered Cementitious Composites with Super-Sulfated Cement: Mechanical, Physical, and Durability Performance

Greener Engineered Cementitious Composite (ECC) – the Use of Pozzolanic Fillers and Unoiled PVA Fibers

Utilization of ground granulated blast-furnace slag and electrolytic manganese residue as a low-carbon cementitious material

Preparation and Hydration Mechanisms of Low Carbon Ferrochrome Slag-Granulated Blast Furnace Slag Composite Cementitious Materials

Preliminary Analysis of the Ductility and Crack-Control Ability of Engineered Cementitious Composite with Superfine Sand and Polypropylene Fiber (SSPP-ECC)

Preparation and Hydration Properties of Steel Slag-Based Composite Cementitious Materials with High Strength

Modification mechanism of flue gas desulfurization gypsum on fly ash and ground granulated blast-furnace slag alkali-activated materials: Promoting green cementitious material

Preparation of steel slag-based cementitious materials compounded with GBFS and phosphogypsum: mix design, hydration, and microstructure characteristic

Mechanical properties and chemical microscopic characteristics of all-solid-waste composite cementitious materials prepared from phosphogypsum and granulated blast furnace slag

Mechanical and environmental performance of engineered geopolymer composites incorporating ternary solid waste

Engineered cementitious composites using blended limestone calcined clay and fly ash: Mechanical properties and drying shrinkage modeling