Abstract:This research is aimed to improve the utilization and activity of anodic catalysts for ethanol electrooxidation. The direct ethanol fuel cell anodic catalysts, PtRuNi/C and PtRu/C, were prepared by chemical reduction method. Their performances were tested by using a glassy carbon disk electrode through cyclic voltammetric curves, chronoamperometric curves, and amperometric i-t curves in a solution of 0.5 mol/L CH3CH2OH and 0.5 mol/L H2SO4. The particle size, lattice parameter, composition, micro-morphology, and surface states of metals in the PtRuNi and PtRu surface particles were determined by X-ray diffraction (XRD), energy dispersive analysis of X-ray (EDAX) analysis, transmission electron microscopy (TEM), and X-ray photoelectron spectrometry (XPS), respectively. XRD analysis showed that both of the catalysts exhibited face-centered cubic structures and had smaller lattice parameters than did Pt/C catalyst. Their sizes are relatively small, about 3.0 nm. Their size distribution of the metal nanoparticles is very homogeneous, without evident agglomeration. There are a lot of Ni oxides with different oxidation states in the PtRuNi/C catalyst from XPS results. No significant differences in the ethanol electrooxidation on both electrodes were found regarding the onset potential for ethanol electrooxidation by using cyclic voltammetry. Yet, the catalytic activity of the PtRuNi/C catalyst is much higher for ethanol electrooxidation than that of the PtRu/C catalyst. Also, its CO-tolerance is better than that of the PtRu/C catalyst. The hydrogen spillover effect of Ni hydroxides and electronic effect of metallic Ni play an important role in the catalytic performance of PtRuNi/C catalyst for ethanol electrooxidation.

Effect of Ethanol on Electrochemical Impregnation

Effect of electrode fabrication methods on the electrode performance for ethanol oxidation

Electrodepostion of compact cadmium deposits in the non-aqueous ethylene glycol solution modified with ethanol

Kinetics of Electrochemical Impregnation Process of Hollow Fibrous Nickel Plaque

Electrodeposition of Ni from Choline Chloride/Ethylene Glycol Deep Eutectic Solvent and Pure Ethylene Glycol

Using Electrode Electrolytes to Enhance Electrokinetic Removal of Heavy Metals from Electroplating Sludge

Removal of Heavy Metals from Electroplating Sludge by Electrokinetic Enhancement Technology

Effect of Ni on PtRu/C Catalyst Performance for Ethanol Electrooxidation in Acidic Medium

Electrophoretic Deposition of Platinum Nanoparticles using Ethanol-Water Mixtures Significantly Reduces Neural Electrode Impedance

Nanoscale Ni-B electrocatalyst prepared from nickel ethylenediamine complex for direct ethanol electrocatalytic oxidation.

Effect of Deposition Time and Temperature on the Performance of Electroless Ni-P Coatings

Influence of polyethylene glycol inhibitors on properties of electroplated copper layer

Effects of dopant ions of polypyrrole on Pd/PPY/Ni composite electrode for electrocatalytic hydrodechlorination

Promoting Effect of Ni(OH)2 on Palladium Nanocrystals Leads to Greatly Improved Operation Durability for Electrocatalytic Ethanol Oxidation in Alkaline Solution

Electrochemical Impedance Spectroscopy and First-Principle Investigations on the Oxidation Mechanism of Hypophosphite Anion in the Electroless Deposition System of Nickel

Effect of Preparation Condition on Electrochemical Property of Nano-Nickel Powders

Effects of Ni(OH)2 Morphology on the Catalytic Performance of Pd/Ni(OH)2/Ni Foam Hybrid Catalyst Toward Ethanol Electrooxidation

Facile Synthesis of Ni/sepiolite and Its Excellent Performance Toward Electrocatalytic Ethanol Oxidation

The Effect of Electrode-Electrolyte Interface on the Electrochemical Impedance Spectra for Positive Electrode in Li-Ion Battery

Nickel Electrodeposition Mechanism from Leaching Solution Containing Ammonia and Chloride