Study on Decoupling Question of Hydraulic Three - Axis Turntable

赵克定,王海鹏,曹健,李军伟

DOI: https://doi.org/10.3969/j.issn.1001-3881.2004.02.020

2004-01-01

Abstract:Based on the model of hydraulic three-axis simulator turntable, through the research of coupling's influence on system precision,the decoupling question is solved by segmental linearization with state feedback.

What problem does this paper attempt to address?

The Control Strategy Study for Hydraulic Shaking Table

Zhangwei Chen

2010-01-01

Abstract:Combined the control theory of hydraulic servo with the testing theory of hydraulic shaking table,the paper presented the dynamic mode1 of the hydraulic shaking table assembled by Hangzhou Econ Technologies for civil engineering department of Xiamen university.A control strategy for the shaking table combined 3-parameters servo control with closed-loop iterative control was proposed,the theory analysis showed that the bandwidth and damping of hydraulic system can be adjusted through 3-parameters servo control;high simulation precision for seismic wave can also be achieved through closed-loop iterative control.The experimental results indicated that the control strategy can obtain the perfect control results on shaking table.
Synchronous Tracking Control for Hydraulic Stewart Platform Based on Combination Tracking Errors in Operation Workspace

Xuanyin Wang,Qiang Li,Jia Cheng

DOI: https://doi.org/10.3321/j.issn:1000-6893.2009.04.023

2009-01-01

Abstract:In order to restrain the coupled disturbance of each degree of freedom of the hydraulic Stewart platform, combination tracking errors, which consist of the tracking errors of each degree of freedom and the coupled position error, are proposed in this article through Taylor series expansion of the trajectory. The coupled position error expressed by the differential position errors of each two neighbor degrees of freedom is used to represent the result of the action of the coupling disturbance. Backstepping design methodology is adopted to develop an adaptive robust position tracking controller with uncertain parameters in the system dynamics. Both parts of the combination tracking errors are shown to be exponentially stable under the proposed control law. Simulation results with the combination of AMESim and MATLAB demonstrate the effectiveness of the approach as contrasted with the traditional proportion-integration-differentiation (PID) controller in improving the error tracking of each degree of freedom with coupling disturbance.
Design And Dynamic Analysis Of A Micro Three-Axis Turntable

Xiaojie Fu,Xuanyin Wang,Songxiao Cao,Yanbing Zhao

2009-01-01

Abstract:This paper introduces a novel asymmetric micro three-axis turntable, which is designed for the research of the flight control system and inertial navigation system of a MAV(micro aerial vehicle) or SUAV (small unmanned aerial vehicle). The turntable is vertical arrangement and driven by electric motors. Photoelectric encoders are used to be feedback elements. The system has a two-stage control structure composed of host computer and slave computer. This turntable is designed to have the characteristics of high precision, simple structure and low cost. Contrast with the exiting symmetric turntable, 3 frameworks of this micro three-axis turntable is designed to be all L type structure. Then, accurate dynamic equations of the three-axis turntable are derived from the perspective of Lagrange's equations of motion for further research.
Decoupling Control of Electro-hydraulic Multivariable Position Control System

Qingfeng Wang

2000-01-01

Abstract:Decoupling of the electro-hydraulic multivariable position coupling system is designed and experimented using diagonal matrix method. The feedback decoupling and feedback complete decoupling schenes are applied respectively to eliminate the effects of structure coupling and outside disturbance force on the decoupiling control. The results show that it has distinct decoupling effect. This method can be realized only by position value of two hydraulic cylinder piston,so that the algorithm is simple and easy to be applied in engineering.
Study of the Inertia and Dynamics Coupling of There Axis Turn Table

Wu-yi WANG,Zhi-gang CHEN,Yi-nan LAI,Guang-yu ZHANG

DOI: https://doi.org/10.3969/j.issn.1007-2683.2005.04.004

2005-01-01

Abstract:The Inertia and dynamics coupling of the three axis turn table of the physical simulation test facility are analyzed,and mathematical models are established.From the relations between Inertia and angles,suggestions that reduce inertia coupling are made for the design of the three axis turn table.An example demonstrates that the maximum inertia coupling is 3%.On the basis of Euler equation,dynamical equations of frames of the turn table are made,which are the base for the docking dynamics analysis of the test facility.
Hierarchical Decoupling Controller with Cylinder Separated Model of Hydraulic Manipulators for Contact Force/Motion Control

Jun Shen,Junhui Zhang,Huaizhi Zong,Min Cheng,Bing Xu

DOI: https://doi.org/10.1109/tmech.2022.3213582

2023-01-01

IEEE/ASME Transactions on Mechatronics

Abstract:Hydraulic manipulators are favored because of their high power density and strong explosive force. As more tasks interact with the environment, better force/motion control performance is demanded. However, hydraulic manipulators are usually driven by closed kinematic loops containing linear hydraulic actuators with passive resolute joints, leading to the difficulty in full dynamic modeling and parameter identification for accurate model-based force/motion control. To overcome this problem, a cylinder separated model is proposed with hydraulic cylinders separated virtually through the concept of virtual equivalent rotational joints. The decoupling model describes the complex dynamics of closed-chain structures based on the Lagrange equation, which is used to identify both inertial parameters of rigid links and cylinders in addition. Besides, a hierarchical decoupling controller is designed by splitting hydraulic cylinder control from the manipulator dynamics on the basis of the decoupling model, and then, the control problems of structure mechanisms and hydraulic system are handled independently. Based on the proposed dynamic model and control strategy, contact force/motion control is realized with the contact force estimated from cylinder pressure sensors. Experiments reveal that the position error of the end effector is reduced at least by 12.7% compared with the conventional controller that ignores coupling problems, whereas the root mean square error of contact force is within 100 N. The proposed strategy shows satisfied performance for hydraulic manipulators, which is also convenient to implement.
Feedback linearization control method for hydraulic flight simulation turntable based on variable inertia model compensation

Xiaochao Liu,Xiaoting Liu,Xinghua Chen,Pengyuan Qi,Yaoxing Shang,Zongxia Jiao

DOI: https://doi.org/10.1007/s11071-024-09388-z

IF: 5.741

2024-03-07

Nonlinear Dynamics

Abstract:The turntable plays an important role in semi-physical simulation of missiles and other aircraft. The precision of its control directly influences aircraft performance. However, the inertial coupling among the three-axis frames of the turntable limits the enhancement of tracking accuracy. This paper establishes a three-axis turntable model, hydraulic model, friction torque model, and gravity torque model, and then obtains expressions for inertial coupling and torque coupling. Based on this, a feedback linearization controller for hydraulic flight simulation turntable is designed with variable inertia model compensation. Finally, through comparative experiments, effectiveness and practicality of proposed control method are verified. Specifically, the proposed control method reduced the average tracking error of the turntable by 18.35% compared to traditional control methods, demonstrating its promising application prospects.

engineering, mechanical,mechanics
Adaptive Control for Three-axle Table Based on Dynamics Decoupling between Frames

王茂,邵长东

DOI: https://doi.org/10.3969/j.issn.1005-6734.2003.05.002

2003-01-01

Abstract:In view of nonlinear coupling between frames of a three-axle table, the method of nonlinear decoupling is presented. And the design of adaptive model following controller based on hyperstability theorem and positivity concept is proposed. The method can solve the problem of the influenced control performance because the parameters are variable during the operation of turntable. The simulation results show that the designed controller can achieve good performance when the parameters are variable in a range, even when the controlled mathematic models order is variable.
Decoupling control for a triaxial 6-DOF Electro-hydraulic shaking table

Gang SHEN,Zhen-cai ZHU,Xiang LI,Yu TANG,Yin-wei YANG,Da-cheng CONG

DOI: https://doi.org/10.13465/j.cnki.jvs.2015.19.001

2015-01-01

Abstract:To solve the coupling problem among DOFs of a Triaxial 6-DOF electro-hydraulic shaking table (EHST),a feedforward compensation decoupling strategy was proposed based on an inverse model.Firstly,for the multi-axis electro-hydraulic shaking table,its system transfer function was taken as a form of matrix and analyzed to deduce the decoupling control scheme based on the system inverse model.Then,the system inverse model and corresponding decoupling controller were obtained by employing the recursive extended least square algorithm (RELS)and the zero phase error tracking technology (ZPET).Finaly,tests were conducted on a 6-DOF electro-hydraulic shaking table to verify the validity of the proposed algorithm.The results demonstrated that the proposed decoupling control strategy can greatly improve the system performance.
Simulation of coupling characteristic of hydraulically driven stewart platform based on dynamics model

Ma Jianming,He Jingfeng,Xiong Haiguo,Jun-wei Han

DOI: https://doi.org/10.1109/WMSO.2008.37

2009-01-01

Abstract:Close chain of spatial mechanical structure of the hydraulically driven Stewart platform makes there exist coupling between the six degrees of freedom. In this paper, it builds the multi-body dynamics model of system with Kane method and then builds the dynamics model of the hydraulic servo system. Combining the two parts, it achieved the whole dynamics model of Stewart platform. By studying the coupling characteristic between six degrees of freedom with the model, it finds out the corresponding relationship of coupling between degrees of freedom and it also finds that dynamics coupling property of system increase with the frequency and reach the maxim value at the natural frequency. When the frequency is greater than the natural frequency the coupling property declines rapidly. At last it verifies the validity of the conclusion through the experiment, so it can use the conclusion as a foundation to study decoupling control strategy which is based on the dynamics model. © 2008 IEEE.
Decoupling Control of an H-drive precision XY Stage

赵冶,朱煜,杨开明,潘尚峰

DOI: https://doi.org/10.3969/j.issn.1001-2265.2010.09.009

2010-01-01

Abstract:In order to get excellent synchronization for motion control of the H-drive precision XY stage with asymmetric structure driven by linear motors,decoupling control of the H-drive precision XY stage was designed by decoupling compensator and output transformation matrix.Relative gain array(RGA) was used to measure the interactions.Besides,the decoupling compensator and output transformation matrix must be parameter-varying with position of x-slide.The result of the simulation shows that the decoupling control structure can acquire good tracking property and effectively restrain the force disturbance of the H-drive.
Decoupling Control of Three-Axis Simulator

GX Yi,CH Wang,W Jiang,BC Shen,ZY Wang

DOI: https://doi.org/10.1109/icmlc.2005.1527119

2005-01-01

Abstract:In this paper, the decoupling problem for a three-axis simulator is considered. The dynamic model of the simulator is established firstly, and the reversibility of the model is proved. The three-axis simulator is highly coupled and nonlinear. The nonlinear autoregressive exogenous input (NARX) neural network is introduced to identify the inverse model of the simulator. A Lyapunov function is introduced to prove the convergence of the network. A strategy for inverse model decoupling control is proposed. The decoupling result in this paper supports the theory and decoupling strategy.
Hydraulic Decoupling and Nonlinear Hydro Turbine Model with Sharing Common Conduit

曾云,张立翔,郭亚昆,董鸿魁

DOI: https://doi.org/10.13334/j.0258-8013.pcsee.2012.14.007

2012-01-01

Abstract:Studying on the hydraulic coupling with sharing common conduit,a decoupling method was proposed to reduce its complexity and difficulty in application due to hydraulic coupling,that the hydraulic coupling was approximately decomposed into multi function depending on each penstock flow.The hydraulic dynamics with elastic water column was converted from transfer function to differential equations in relative value,and differential equations model of hydro turbine was composed by connecting it with motion equation of main servomotor.Those couplings of another penstocks obtained by decoupled were taken as additional disturbance in hydro turbine model,which input control was decoupling in this way,and simplify the controller design.The simulation results show that proposed decoupling model is effective.
Decoupling Compensation for Damping Improvement of the Electrohydraulic Control System with Multiple Actuators

Min Cheng,Junhui Zhang,Bing Xu,Ruqi Ding,Jing Wei

DOI: https://doi.org/10.1109/tmech.2018.2834936

2018-01-01

IEEE/ASME Transactions on Mechatronics

Abstract:This paper proposes a decoupling compensation method for damping improvement of the electrohydraulic control system with multiple actuators. The low damping property of hydraulic systems has been a remarkably troublesome issue for a few decades. Previously, this issue with one actuator has been addressed effectively by state feedback and signal compensation, e.g., dynamic pressure feedback. However, the poor damping with multiple actuators is still intractable and pendent due to the complex coupling effect of different loads. A decoupling compensator based on pump/valve combined control is proposed for a typical electrohydraulic system with multiple actuators for mobile machinery. Using decoupling control of different load branches, the coupling hydraulic circuit with multiple cylinders is transformed into multiple separate single-cylinder circuits with dynamic compensation. The dynamic characteristics of different actuators are then improved synchronously without mutual interference, while the steady performance remains the same without loss of controllability. Compound motion tests on a 2-ton hydraulic excavator were carried out. The results showed that the proposed compensator reduced velocity and pressure oscillations under different working conditions, so the dynamic performance is improved for the multiactuator system.
Dynamic decoupling and compensation based on the inverted network technique and experiment research for multi-axis hydraulic road simulator

Xiao Wang,Fanglin Hu,Longyuan Yao,Kun Li,Junwei Han

DOI: https://doi.org/10.1177/09544062241277742

2024-09-21

Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science

Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. This paper presents a dynamic decoupling and compensation approach to eliminate channel interaction for a multi-axis hydraulic road simulator. Misalignment of the concentrated moving mass centroid on the entire test bench with the control point and inconsistencies in actuator dynamics leads to dynamic coupling, which deteriorates the motion performance of the system. To solve the problem, an inverted decoupling and compensation network based on an identification model is proposed. Firstly, the system is modeled using the recursive extended least square (RELS) identification method. In the feedforward compensation modeling process, the steady-state inverse is obtained using zero-magnitude error technology control (ZMETC). In addition, a finite impulse response (FIR) filter with an adaptive algorithm is employed to reduce the adverse impact of the modeling error. The proposed decoupling strategy is validated by conducting experiments using a multi-axis hydraulic road simulator. The experimental results indicate that the designed compensator can effectively decrease the cross-coupling of multi-input and multi-output (MIMO) systems. The suggested approach is also applicable to applications that necessitate the elimination of interactions between different control variables.

engineering, mechanical
Iterative Tuning of Decoupling Controller for 3-DOF Precision Motion Stage

Wei Teng,Qingfeng Gao,Xin Wu,Haihua Mu

DOI: https://doi.org/10.1007/s12206-011-1104-6

IF: 1.81

2012-01-01

Journal of Mechanical Science and Technology

Abstract:A practical iterative tuning algorithm of a decoupling controller is presented to eliminate intrinsic coupling among 3-DOF precision motion stage. General decoupling control cannot eliminate coupling completely, which will prevent the enhancement of control accuracy in high-precision motion system. The proposed algorithm can be used to tune the parameters of a decoupling controller iteratively through minimizing a quadratic cost function of the tracking error in non-movement direction when the stage moves in one direction. The tuning algorithm addressed for the motion stage needs only measurement signals in an actual motion system rather than a detailed model of the stage. The proposed algorithm is demonstrated by experimental results. It can be applied further in other multi-DOF motion systems.
Modeling and Vibration Decoupling Control of Multi-Axial Shaking Table

Zhang Lianpeng,Yang Zhidong,Qu Zhiyong,Han Junwei

DOI: https://doi.org/10.2991/iiicec-15.2015.409

2015-01-01

Abstract:Traditional control strategy study of the multi-axial electro-hydraulic shaking table(MAEHST) is based on linear model, ignoring the coupling and nonlinearity factors, which results in the waveform distortion and the control precision. To overcome these limitations, a model considering the hydraulic system nonlinearity and mechanical coupling using the software Simulink/SimMechanics is built. A vibration decoupling control strategy based on multiple input multiple output (MIMO) system identification is proposed to improve the waveform replication precision. The proposed control method applies the MIMO H1 estimator to identify frequency response function matrix (FRFM) of the system, not only considering the diagonal element, but the off-diagonal element to acquire the coupling characteristics of six degrees of freedom (DOFs) of MAEHST. And then the inverse frequency response function matrix (IFRFM) is calculated using the singular value decomposition technique to obtain the drive signal combined with the reference signal. Simulation experiments are carried out, and the results indicate that the MIMO vibration decoupling control strategy successfully minimizes the coupling and improve the waveform replication precision of the shaking table.
Modeling of AMESim Based Hydraulic Parallel Mechanism and Simulation of Its Coupling Characteristics

WANG Wei,FU Xin,XIE Hai-bo,YANG Hua-yong

DOI: https://doi.org/10.3785/j.issn.1008-973x.2007.11.021

2007-01-01

Abstract:A novel universal simulation model of hydraulic six-degree of freedom parallel mechanism was presented,in which the hydraulic actuator servo system was built in the AMESim,and the parallel mechanism part was built in the Simulink.In the AMESim model,the equivalent load of hydraulic actuator is from the Simulink model instead of equivalent mass.The combined simulation model takes the details of hydraulic system into consideration to ensure the accuracy,and provides a convenient research technique for hydraulic parallel mechanism.The coupling characteristic of the parallel mechanism was studied through analyzing the dynamic consistency of six actuators using the simulation model.The results show that coupling phenomena appear when the frequency responses of the six actuators were different,and the coupling becomes stronger when the difference among the actuators increases.Thus the dynamic consistency of all actuators must be ensured during the design of parallel mechanism.
Dynamics Decoupling Control Of Parallel Manipulator

Jun-Wei Han,Wei Wei,Zhi-Dong Yang

DOI: https://doi.org/10.1007/978-3-319-74363-9_5

2018-01-01

Abstract:Due to the eccentric load of parallel manipulator, dynamic coupling occurs between the various degrees of freedom. As a typical parallel mechanism, the dynamic model of redundant shaking table is built. Coupling force observaction based on coupling model is introduced to the DoFs control structure. The coupling forces are controlled as disturbance forces on hydraulic system by distributing it to each actuator through Jacobi matrix transformation. Decoupling control is given based on the dynamic model as well as a feed forward disturbance force compensation control strategy. However, due to the fact that differentiating acceleration which contains large noise is needed in decoupling control based on dynamic model, modal decoupling control is given. Modal equation of redundant shaking table is given by considering hydraulic cylinder as a hydraulic spring. Through standard modal matrix and its inverse matrix, the redundant shaking table is controlled in non-coupling modal space instead of DoFs space. By analyzing the relationship between the modal matrix and the coupling characteristics of different modal DoFs, an experimental method is given for determining the modal matrix. Simulation analysis shows that compared with decoupling control based on dynamic model, the modal space decoupling control can more effectively reduce the dynamic coupling among DoFs of the redundant shaking table. A control system of the redundant shaking table is developed using rapid control prototyping technology based on xPC Target. Detailed experimental analysis and research are carried out on the proposed coupling characteristic analysis and decoupling control strategies. Experimental results demonstrate that the proposed decoupling control strategies are effective and advanced.
Decoupling Modeling Design and High-Precision Position Control of Fast Steering Mirror

Lin Wang,Xuelian Liu,Shuning Liang,Chunyang Wang

DOI: https://doi.org/10.1016/j.precisioneng.2024.03.005

IF: 3.315

2024-01-01

Precision Engineering

Abstract:For a two-axis fast steering mirror (FSM) based on the flexible chain structure support and voice coil motor drive, the two axes are strongly coupled. This strong coupling may decrease the system positioning accuracy. In this study, the electric kinematics model associated with the voice coil motor and the motion and frequency equations associated with the flexible chain structure were analysed. A comprehensive system model was established considering shaft coupling, a digital controller with compensation coupling was designed, and the method of active compensation was used for decoupling. The experimental results showed that compared with the traditional non-decoupling control algorithm, the decoupling control method decreased the coupling degree from 7% to 0.8% and reduced the positioning accuracy error from 1.5% to 0.3%.

Study on Decoupling Question of Hydraulic Three - Axis Turntable

The Control Strategy Study for Hydraulic Shaking Table

Synchronous Tracking Control for Hydraulic Stewart Platform Based on Combination Tracking Errors in Operation Workspace

Design And Dynamic Analysis Of A Micro Three-Axis Turntable

Decoupling Control of Electro-hydraulic Multivariable Position Control System

Study of the Inertia and Dynamics Coupling of There Axis Turn Table

Hierarchical Decoupling Controller with Cylinder Separated Model of Hydraulic Manipulators for Contact Force/Motion Control

Feedback linearization control method for hydraulic flight simulation turntable based on variable inertia model compensation

Adaptive Control for Three-axle Table Based on Dynamics Decoupling between Frames

Decoupling control for a triaxial 6-DOF Electro-hydraulic shaking table

Simulation of coupling characteristic of hydraulically driven stewart platform based on dynamics model

Decoupling Control of an H-drive precision XY Stage

Decoupling Control of Three-Axis Simulator

Hydraulic Decoupling and Nonlinear Hydro Turbine Model with Sharing Common Conduit

Decoupling Compensation for Damping Improvement of the Electrohydraulic Control System with Multiple Actuators

Dynamic decoupling and compensation based on the inverted network technique and experiment research for multi-axis hydraulic road simulator

Iterative Tuning of Decoupling Controller for 3-DOF Precision Motion Stage

Modeling and Vibration Decoupling Control of Multi-Axial Shaking Table

Modeling of AMESim Based Hydraulic Parallel Mechanism and Simulation of Its Coupling Characteristics

Dynamics Decoupling Control Of Parallel Manipulator

Decoupling Modeling Design and High-Precision Position Control of Fast Steering Mirror