Abstract:Heat-treatment processes to obtain carbide-free upper bainite, low bainite and low-temperature bainite in the 34MnSiCrAlNiMo medium-carbon steel were explored. Results show that in the steel bainite transformation mainly goes through three stages: short incubation, explosive nucleation and slow growth. When transformation temperature, T > Ms + 75 degrees C, upper bainite consisted of catenary bainitic ferrite and blocky retained austenite is obtained in the steel. When Ms + 10 degrees C < T < Ms + 75 degrees C, lower bainite is the main morphology composed of lath-like bainitic ferrite and flake-like retained austenite. When T < Ms + 10 degrees C, the lower bainite, also known as low-temperature bainite, is obtained, which contains much thinner lath-like bainitic ferrite and film-like retained austenite. Mechanical testing results show that the lower the transformation temperature is, the better comprehensive performance is. The low-temperature bainite has the very high tensile strength and impact toughness simultaneously. The lower bainite has lower tensile strength and higher impact toughness. The upper bainite has higher tensile strength and lower impact toughness. The big difference of the mechanical performance between these kinds of bainite is mainly caused by interface morphology, size, and phase interface structure of the bainitic ferrite and the retained austenite. Additionally, when the bainite transformation temperature is decreased, the high-angle misorientation fraction in packets of bainite ferrite plates is increased. High-angle misorientation between phase interfaces can prevent crack propagation, and thus improves impact toughness. (C) 2014 Elsevier Ltd. All rights reserved.

Study on the Formation of Carbide in High ManganeseSteel and its Solution at Elevated Temperature

Study on Evolution Behavior of Carbides in Industrial‐Grade American Iron and Steel Institute M35 High‐Speed Steel Produced by Electroslag Remelting

EFFECT OF MODIFICATION ON AS-CAST AND HEAT TREATED MICROSTRUCTURE OF SUPER-HIGH MANGANESE STEEL

Gradient microstructure evolution and hardening mechanism of carburized steel under novel heat treatment

Experimental and theoretical analysis of multiphase microstructure in a newly designed MnSiCrC quenched and partitioned steel to promote bainitic transformation: The significant impact on mechanical properties

Carbonitride Dissolution And Austenite Grain Growth In A High Cr Ferritic Heat-Resistant Steel

Evolution of Microstructures and Mechanical Properties During Solution Treatment of a Ti–V–Mo-containing High‑manganese Cryogenic Steel

High-temperature oxidation behavior and subsurface phase transformation of high-Mn high-Al steel

Effect of progressive solid-solution treatment on microstructures, mechanical properties and impact abrasive wear behavior of alloyed high manganese steel

Insights into the High Magnetic Field-Induced Austenite Formation in Medium Manganese Steel

Evolving Mechanism of Eutectic Carbide in As-Cast AISI M2 High-Speed Steel at Elevated Temperature

Evolution of Carbides and Carbon Content in Matrix of an Ultra-High Carbon Sintered Steel During Heat Treatment Process

Effect of Heat Treatment Temperature on the Microstructure, Wear and Friction of Ni–Nb–V Alloyed Manganese Steel

Effect of Mn addition on microstructure and mechanical properties of GX40CrNiSi25-12 austenitic heat resistant steel

Early Martensitic Transformation in a 0.74C–1.15Mn–1.08Cr High Carbon Steel

Austenite Thermal Stabilization Through the Concentration of Manganese and Carbon in the 0.2c–5mn Steel

Apparent Morphology and Structure of Martensite in Ultrahigh Carbon Steel

Tailoring the metastable reversed austenite from metastable Mn-rich carbides

A study on the microstructural evolution and subgrain size dependent constitutive equation of a type of maraging steel in the solid solution treatment process

Carbide-Free Bainite in Medium Carbon Steel

Κ-Carbide Hardening in a Low-Density High-Al High-Mn Multiphase Steel