Abstract:The impact strength of nylon 6 (polyamide 6) can be improved by blending impact strength modifier at ambient temperature and then the applications of nylon 6 can be expanded widely. Polyamide (6) PA 6/poly(ethylene-1-octene) elastomer (POE)/poly(ethylene-1-octene) elastomer grafted by maleic anhydride (POE-g-MA) ternary blends were prepared in corotating twin-screw extruder by two kinds of extrusion processes, more than 10-fold increase of impact strength at ambient temperature was obtained from impact test of specimens, not at much expense of tensile properties. The influence of extrusion process, that is, one- and two-step extrusion, on the micromorphology of toughing nylon 6 blends was investigated systematically. Scanning electron microscopy was used to observe the fracture surfaces of bars prepared by injection-molding machine. In addition to particle size and distribution, interparticle distance ( τ) between neighboring dispersed phase particles in PA6/POE-g-MA/POE ternary blends was calculated and used to characterize the micromorphology. Supertoughness was obtained in both ternary blends, and the interparticle distances ( τ) were 0.228 and 0.179 μm, respectively, which were less than the critical τ c (0.3 μm) in nylon/rubber blends. The results showed that more homogeneous distribution of POE phase in nylon 6 matrix was found in blends prepared by two-step extrusion method, in which the average particle size of POE phase was 0.313 μm, while the average particle size in blends prepared by one-step method was 0.399 μm. The half-peak width of Gaussian distribution curve of particle size in blends prepared by one-step extrusion method was 0.278, which is higher than that of blends prepared by two-step method with the value of 0.248.

THE EFFECT OF ULTRASONIC OSCILLATIONS ON PROPERTIES AND MORPHOLOGY OF POLYAMIDE-6/HIGH-DENSITY POLYETHYLENE BLENDS

Effect of Oscillatory Shear on the Mechanical Properties and Crystalline Morphology of Linear Low Density Polyethylene

Effect of Superimposed Oscillatory Shear on Crystalline Behavior and Mechanical Properties of PE-LLD

Structure Evolution and Properties Enhancement of Polyamide‐6/polyamide‐1010 Films under Uniaxial and Biaxial Stretching

Effect Of Polyethersulfone On The Mechanical And Rheological Properties Of Polyetherimide-Modified Epoxy Systems

Crystallization Behavior of Reactive Blends Between Pbs and Pa6icot

Physical and chemical effects of ultrasound vibration on polymer melt in extrusion

Ultrasonic dyeing of polylatic acid blended fabric

Mutual Nucleating and Crystallization Behavior of Poly (ethylene Terephthalate)/polyamide 66 Blends

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Effect of small amount of ultra high molecular weight component on the crystallization behaviors of bimodal high density polyethylene

MORPHOLOGICAL EVOLUTION AND VISCOELASTIC BEHAVIOR OF COMPATIBILIZED HDPE/PA6 BLENDS

Exploring the Entangled State and Molecular Weight Ofuhmwpeon the Microstructure and Mechanical Properties Ofhdpe/uhmwpeblends

The influence of extrusion process on micromorphology of PA 6/POE/POE-g-MA ternary blends: A quantitative analysis

ULTRAVIOLET IRRADIATION MODIFICATION OF HDPE AND MECHANICAL PROPERTIES OF ITS BLEND WITH PVA

Studies On High Density Polyethylene (Hdpe) Functionalized By Ultraviolet Irradiation And Its Application

Study on Structure and Properties of HDPE Functionalized by Ultraviolet Irradiation in Air and O2 Atmosphere

Dynamic Rheological Behavior of Hdpe/Uhmwpe Blends

The influence of UHMWPE with varying morphologies on the non-isothermal crystallization kinetics of HDPE

The effect of stretching on polyamide – 6: assessment of crystallinity, mechanical properties, and surface roughness

Effect of Entangled State of Nascent UHMWPE on Structural and Mechanical Properties of HDPE/UHMWPE Blends