Model Analysis and Performance Curves for Tension Control System

纪铜钊,李兴根

DOI: https://doi.org/10.3969/j.issn.1005-2895.2003.01.005

2003-01-01

Abstract:This paper first deduces an accurate tension model for gravure press, and then shows the performance curves adopted in practice application of a tension controller.

What problem does this paper attempt to address?

ANALYSIS AND MODIFICATION OF HYDRAULIC ROLLER BENDING FORCE CONTROL SYSTEM

陈为国,陈章位,丁凡,吴根茂

DOI: https://doi.org/10.3321/j.issn:0449-749x.2001.11.011

IF: 1.7031

2001-01-01

Ironmaking & Steelmaking

Abstract:A mathematical model was put forward for the hydraulic roller bending force control system of Baosteel's hot strip rolling mill A hydraulic mechanical filter was built in this control system to eliminate damage of roller bending force sensors The device satisfactorily protects the sensor from hydraulic impact and the control precision was improved
The Research of the Tension Control System of Optical Fiber Coil Winding Machine

ZHAO Jin-hong,SHU Xizo-wu,MOU Xu-dong,LIU Cheng

DOI: https://doi.org/10.3969/j.issn.1005-5630.2005.02.008

2005-01-01

Abstract:The optical fiber coils is the sense core of the optical fiber gyroscope. A minimal and steady tension is the main factor to evaluate the quality of the optical fiber coils . Controling the tension of the optical fiber in the process of the winding with the windmachine, we can get the expected value of tension. The performance of the optical fiber coils can be improved.
Modeling of Tension Control System with Passive Dancer Roll for Automated Fiber Placement

Yi Liu,Qiang Fang,Yinglin Ke

DOI: https://doi.org/10.1155/2020/9839341

IF: 1.43

2020-01-01

Mathematical Problems in Engineering

Abstract:The fiber tension should be kept constant during the automated placement of fiber prepreg. The velocity of the fiber placement end-effector moving on complex aircraft panel mould surface varies rapidly, which greatly disturbs the precision of tension control. This paper proposes a tension control strategy combining active control and passive control. The pay-off motor controls the fiber tension directly and a passive dancer roll is designed theoretically as the equipment for attenuation of tension disturbance to realize the real-time compensation of low-frequency velocity variations. The nonlinear model of tension control system, which includes the dynamics of the passive dancer roll, is established, and the effect of dancer roll parameters on its disturbances attenuation performance is analyzed. The controller is designed using the H∞ mixed sensitivity method. An experimental tension control precision about 2% is obtained at stable placement speed on the automated fiber placement (AFP) machine. The experiments also indicated that the tension would not vary over 1 N at a maximum acceleration of 4 m/s2.
Nonlinear active control of tensegrity structures

许贤,罗尧治,沈雁彬

DOI: https://doi.org/10.3785/j.issn.1008-973X.2010.10.023

2010-01-01

Abstract:The active control of tensegrity structure was analyzed in order to effectively solve the vibration control problem of tensegrity structure under various dynamic actuations and ensure the function and safety of the structure.The state description of tensegrity structure was derived from the electromechanical actuation equation.The electromechanical optimal control equation for tensegrity structure was obtained based on the instantaneous optimal control and the Newmark relation.The geometrical nonlinearity of the structural system was considered by adding an iteration process on the Newmark algorithm.Then the electromechanical and nonlinear active control of tensegrity structure was achieved.Numerical simulations with a double-layer cylinderical tensegrity structure were conducted to verify the validity of the method.The effect of the number of actuators and the layout of actuators to the control effect and control efficiency was also investigated.
Model of Straightening T-rail Based on Elastic-Plastic Theory

周磊,余忠华

DOI: https://doi.org/10.3785/j.issn.1008-973x.2010.02.029

2010-01-01

Abstract:A mathematical model of reverse bending straightening was proposed based on elastic-plastic mechanics in order to straightening T-rail's bending distortion.The key parameters of straightening T-rail,such as the disposal of press points and support points,straightening moment,reverse bending cur-vature、down stroke,were analyzed.The formula for computing T-rail's reverse bending curvature in cor-responding to its original deformed curvature was deduced.The expression for accounting the reverse stroke of pressing down was given for operating convenience.The model was used to straightening special T-rail,and the connection curves were presented.The curves reflected the relation between the reverse bending curvature and the original curvature,and the relation between the stroke of pressing down and the original bending.The theoretical results were compared with the finite element method results.Results show that the model is practical.
Study on Coil Tension Fuzzy Control by Rotary Magnetorheological Damper

CHEN Zhao-bo,TU Feng-chen,LI Ming-zhang,JIAO Ying-hou,LI Hua

DOI: https://doi.org/10.3321/j.issn:0367-6234.2007.11.013

2007-01-01

Abstract:In order to reduce rolling tension fluctuation, a new type of magnetorheological damper is proposed. The structure of the damper is determined, and a damping torque model is established. According to the simulation results, the damping torque increases exponentially with the current increase. In case of small current, the damping torque increases linearly, and when the current is greater than 5A, the damping torque becomes saturated. The damping torque is proportional to rotational speed. A fuzzy logic method is put forward to control tension fluctuation by controlling the damping torque. The fuzzy input and output variables are determined, and the fuzzy control regulation is obtained. The simulation results show that the tension fluctuation amplitude can be reduced by applying rotary magnetorheological damper to tension fuzzy control.
Vibration Analysis of High-speed Traction Elevator Based on Guide Roller-rail Contact Model

梅德庆,杜小强,陈子辰

DOI: https://doi.org/10.3901/jme.2009.05.264

2009-01-01

Journal of Mechanical Engineering

Abstract:Guide rollers installed on high-speed traction elevator to make it run steadily have nonlinear rate-dependent characteristic, which induces the elevator vibration when it is stimulated by the roller roundness tolerance and the guide rail irregularity. According to the Kalker’s simplified theory of three-dimensional Hertzian rolling contact, the contact model of guide roller-rail is set up and the expressions of the contact stiffness in three directions are derived to calculate the normal Hertzian force and the tangential creep force. The irregularity excitation between guide roller and rail is fitted by taking the roller roundness tolerance and the rail profile irregularity into account. The system dynamic equations of high-speed traction elevator are constructed. Using Newmark method, the vibration behavior of a high-speed traction elevator is analyzed. Compared with the practical measurement results both in time and frequency domain, the calculated results are in good agreement, which means that the system dynamic model of high-speed traction elevator based on guide roller-rail contact model is valid. Therefore the proposed model can be used to predict the vibration response of high-speed traction elevator.
Modeling and Analysis of Web Tension Between Two Adjacent Printing Rollers in Shaft-Less Drive Gravure Printing Systems

Kui He,Kedian Wang,Dongsheng Zhang,Shanhui Liu,Jian Li,Qing Wen

DOI: https://doi.org/10.1109/iaeac.2017.8054315

2017-01-01

Abstract:In shaft-less drive gravure printing machines, each gravure printing roller is driven by an individual servo motor. The register accuracy is an important performance indicator for gravure printing process, and it is based on the stability and accuracy of the web tension between the printing rollers. Therefore, the mathematical model of the web tension between two adjacent printing rollers is studied for the shaft-less drive gravure printing machines in this paper. According to the working principle, the tension model between two adjacent printing rollers is derived, and then it is analyzed deeply from three different aspects. Some numerical simulations are carried out to verify the tension model. It shows that the simulation results are in accord with the analysis and the established tension model is reliable.
Thermo-Mechanical Coupling Analysis of the Actuating Mechanism in a High Speed Press

Jin Cheng,Zhendong Zhou,Yixiong Feng,Zhenyu Liu,Yangyan Zhang

DOI: https://doi.org/10.1007/s12541-018-0078-z

IF: 2.0411

2018-01-01

International Journal of Precision Engineering and Manufacturing

Abstract:In order to ensure the manufacturing precision of an ultra-precision high speed press, an integrated thermo-mechanical coupling model of its actuating mechanism is proposed, which includes the mechanical models of the slider and crankshaft, the thermal models for calculating the heat generation powers at different bearings as well as the heat transfer and heat dissipation in the actuating mechanism. The validity of the proposed thermo-mechanical coupling model is verified by a thermal equilibrium experiment when the press operates under the full load of 3000kN at 300 rpm. A sensitivity analysis is conducted to investigate the simulation errors resulting from the variation of the ambient temperature, the results of which demonstrate that the average ambient temperature should be applied for improving simulation accuracy. Then the thermal stiffness of the actuating mechanism and the thermo-mechanical coupling characteristics of different parts are analyzed by the proposed model with the average ambient temperature applied. The influences of the thermally induced loads on the thermal stiffness are discussed in detail. It is concluded that the temperature rise of the actuating mechanism in the stamping process of a high speed press should be fully considered in the design phase for ensuring its manufacturing precision.
TENSION ANALYSIS OF FILAMENT WINDING PROCESS

王春香,付云忠,杨汝清,王永章,路华

DOI: https://doi.org/10.3321/j.issn:1000-3851.2002.03.024

2002-01-01

Abstract:Within the field of fiber, paper making, plastic and metal plating, one of the key techniques to guarantee the product quality is to control the winding tension of linear, strip and area materials. The tension changing pattern and the factors that influence the tension in the filament winding process were analyzed, and a program scheme for calculating the tension control torque was provided. The actual winding results show that the formula drawn is proper and reasonable, and the fluctuation rate of the yarn tension calculated by use of the formula is lower than 5%.
Design of tension control of a winding machine for rectangular component

Yang Gong-yuan

Abstract:In order to found out the key parameters which affect tension control accuracy,the mathematical models for winding and unwinding are derived.For the controlling is difficult than the winding with round section component,the automatic gain control,the identification of system,dynamic compensating control and predictive control algorithm are used.Control system adopt master/slave control mode which based on IPC,high performance programmable multi-axis controller and tension controller.The dynamic tension accuracy of the tension control system is ±4%.Experimental results show that the system is well qualified with high control precision and high reaction speed.

Engineering
Research on the Register System Modelling and Control of Gravure Printing Press

J. Li,X. Mei,T. Tao,S. Liu

DOI: https://doi.org/10.1177/0954406211415914

2011-01-01

Abstract:The register accuracy is the most important performance of gravure printing press. In order to improve the control accuracy of register, an accurate mathematical model of the register error and a high-performance controller should be researched. In this article, the mathematical model of the register error and the elimination of interference caused by the speed and tension of web by the feed-forward control scheme are studied. The established mathematical model and the feed-forward control scheme are validated by the numerical simulation and multi-colour gravure printing press test. The results show that the established register error model is accurate and reliable, and the designed feed-forward control scheme effectively reduces the register error caused by the tension and speed fluctuation.
Dynamic Characteristic Analysis of Edge Position Control System for Tension Reel

王东,首天成

DOI: https://doi.org/10.3969/j.issn.1672-8904.2009.06.007

2009-01-01

Abstract:A mathematic model of Edge Electro-hydraulic Position Control System of tension reel is gained based on the electro-hydraulic servo control theory.Meanwhile, this mathematic model is verified and analyzed through the testing on site.Results prove that this mathematic model is satisfied for practice, and show that it provides a theoretical basis for studies on the dynamic performance of the system.
Research on dynamic characteristics of jigger electro-hydraulic tension control system

王传礼,丁凡,殷建立,李其朋,方平

DOI: https://doi.org/10.3785/j.issn.1008-973X.2004.05.023

2004-01-01

Abstract:The composition and working principle of jigger electro-hydraulic tension control system were analyzed. In order to enhance the stability and precision of the system, improvements such as adding an integrating compensating element and adding a damper in tension detection element were presented. Then the mathematical models of the system were established. By the use of Simulink Toolbox of Matlab, the system's dynamic characteristics were simulated. Finally the experiments were carried out under typical working conditions, and the tension curves at different input voltage and tension change were obtained. Numerical simulation results accord with the experiment in general, which proves the correctness of the mathematical models. And the results show that the suggested improvements can make the stability and precision of the electro-hydraulic tension control system better.
Research on Tension Control Model for Traction and Take-up System of Loom

Youzhao Wang,Jing Huang,Hanwei Chen

DOI: https://doi.org/10.4028/www.scientific.net/amr.627.444

2012-01-01

Advanced Materials Research

Abstract:This paper does some researches on the framework and control mechanism of traction and take-up system of Loom, which keep the winding tension constant. A traction and take-up control model using fuzzy neutral network adaptive PID algorithm is designed. The results prove this model is available in constant tension control system. The constant tension control system makes traction and take-up system operate more precisely and improves the quality of fabric.
Building Up Of Tension Control Experimental System Based On Magnetorheological Damper

Liyong Hu,Di Zheng,Xilin Zhu,Wencong Ye,Jianming Zhan,Guoping Li

2008-01-01

Abstract:Winding system is used widely in many fields such as textile, printing, papermaking, metallurgy, etc. Keep the tension changeless or changing regularly in the course of coiling. Through the tension sensor to measure tension, Variable frequency motor to output corresponding torque and rotate speed after the data processing of the computer, we can accurately control the tension fleetly by controlling the magnetorheological damper. The magnetorheological damper is designed and tested, and other parts of the tension control experimental system has been designed and analyzed in the article.
Influence factor analysis for tension control based on MRF damper

Liyong Hu,Di Zheng,Jianming Zhan,Yimin Deng

DOI: https://doi.org/10.4028/www.scientific.net/AMM.37-38.529

2011-01-01

Abstract:Tension control is widely used in industrial production. This paper gives one tension control method using MRF damper as the actuator. The principle of the tension generation is introduced. Through analysis and numerical simulation, the main influence factor of tension changing is obtained. The result of simulation shows that the influence factor of the tension includes the excitation electric current of the MRF damper, the radius of a wheel, rotate speed, the fluctuation of the rotate, etc. These factors present strongly nonlinearity. Through controlling the excitation electric current of MRF damper, the fluctuation of tension can be controlled to decrease.
Research on a Precision Tension Control System with a Magnetic Particle Clutch As the Actuator

Wang Chunxiang,Yang Ruqing,Wang Yongzhang,Lu Hua

DOI: https://doi.org/10.1007/s00170-004-2190-8

2004-01-01

Abstract:The open-loop tension control system, with an industrial control computer as the core and a magnetic particle clutch as the actuator, equipped with three compensation techniques, is researched and manufactured. It has been verified by experiment that the principle of the precise tension control system designed is right and that its properties are reliable. It can ensure tension control stability of the yarn in the filament winding process and increase the response velocity and the stability of the control precision of the whole system.
Analysis of on-line tension control systems for false twister

Huang Fenggui,Shao Hua,Zhao Youli

DOI: https://doi.org/10.3969/j.issn.1001-0041.2007.06.016

2007-01-01

Abstract:Based on the tension control principles for a false twister,the on-line tension control systems were analyzed for false twisters.The most efficient way was to control untwisting tension(T_2)throngb D/Y ratio regulation,but a single-spindle motor and a frequency converter was necessarily required;T_2 was regulated by adjusting the friction between the threads in false twister, which was more applicable in achieving T_2 control during the production both on apron false twister and on stacked tray false twist- er and more beneficial to the quality control during the production.
Analysis and application on model of press straightening process with FEM

李骏,邹慧君,熊国良,陈慧

DOI: https://doi.org/10.3969/j.issn.1001-196X.2004.01.008

2004-01-01

Abstract:Load-deflection model of press straightening process is explained. The method and procedures of establishing load-deflection model by using ANSYS software are described. Based on the model, the straightening stroke can be calculated, so it is solved to apply FEM to automatic straightening machine. An example is given, calculation results by FEM are in good agreement with the experimental results. The validity of the method is proved.

Model Analysis and Performance Curves for Tension Control System

ANALYSIS AND MODIFICATION OF HYDRAULIC ROLLER BENDING FORCE CONTROL SYSTEM

The Research of the Tension Control System of Optical Fiber Coil Winding Machine

Modeling of Tension Control System with Passive Dancer Roll for Automated Fiber Placement

Nonlinear active control of tensegrity structures

Model of Straightening T-rail Based on Elastic-Plastic Theory

Study on Coil Tension Fuzzy Control by Rotary Magnetorheological Damper

Vibration Analysis of High-speed Traction Elevator Based on Guide Roller-rail Contact Model

Modeling and Analysis of Web Tension Between Two Adjacent Printing Rollers in Shaft-Less Drive Gravure Printing Systems

Thermo-Mechanical Coupling Analysis of the Actuating Mechanism in a High Speed Press

TENSION ANALYSIS OF FILAMENT WINDING PROCESS

Design of tension control of a winding machine for rectangular component

Research on the Register System Modelling and Control of Gravure Printing Press

Dynamic Characteristic Analysis of Edge Position Control System for Tension Reel

Research on dynamic characteristics of jigger electro-hydraulic tension control system

Research on Tension Control Model for Traction and Take-up System of Loom

Building Up Of Tension Control Experimental System Based On Magnetorheological Damper

Influence factor analysis for tension control based on MRF damper

Research on a Precision Tension Control System with a Magnetic Particle Clutch As the Actuator

Analysis of on-line tension control systems for false twister

Analysis and application on model of press straightening process with FEM