Abstract:In this paper, a novel hard nickel composite coatings were fabricated by wide-band laser cladding technique. The effects of Si alloying on the composite coatings were investigated by microstructure characterization, phase identification, microhardness and wear resistance. Results showed that the in-situ precipitated phases in the laser molten pool were composed of the γ-Ni solid solution and hard phases such as Cr 23 C 6 , CrSi, Cr 5 B 3 . With the increase of Si element, the morphology of the precipitated phases changed significantly. When the added content of Si was 1.0 wt.%, the precipitated phase was a mainly block morphology. As the added content of Si was increased to more than 2.0 wt.%, the main precipitated phase was transformed into a long stripe morphology. With the increase of Si content, the stripe-like precipitated phase was gradually refined and finally becomes density needle-like precipitates. Element distribution analysis showed that the block precipitated phase was enriched in Cr, W and Si elements. Additionally, the enriched elements in the long strip precipitation phase were essentially the same as those in the block precipitation phase. The added Si element was highly involved in the in-situ reactions of precipitated phase. The TEM results showed that the precipitated phases contained the crystal structures of Cr 5 B 3 and Cr 7 C 3 . The pin-on-disc wear tests revealed that the composite coating with the addition of 6 wt.% Si exhibited the best wear resistance in the experimental group. The average friction coefficient was about 0.6 and the wear mass loss rate was about 2.38 × 10 −5 g/m under counter-abrasive conditions. The worn surface analysis indicated that the wear mechanism of composite coatings was mainly abrasive wear. The refined needle-like precipitated phase was closely bound to the matrix and thus not easy to peel off, providing a significant improvement in the wear resistance of the laser cladding coatings.

Microstructure and Properties of Broad-Beam Laser Clad Ni60B + 30 % WC Composite Coatings

Microstructure and Properties of WC/Ni-Based Laser-Clad Coatings with Different WC Content Values

Study of Microstructure and Properties of Laser Cladding Ni60-WC + TiC Composite Coating

Effect of Process Parameters on Microstructure and Properties of Laser Cladding Ni60+30%WC Coating on Q235 Steel

Comparative investigation on microstructures and properties of WC/Cr 3 C 2 reinforced laser cladding Ni-based composite coatings subjected to ultrasonic impact treatment

Microstructure and properties of Ni-WC gradient composite coating prepared by laser cladding

Effect of WC content on microstructure and properties of high-speed laser cladding Ni-based coating

Microstructure and Property of Laser Cladding Ni-based Alloy Coating Reinforced by WC Particles

Microstructure and Wear Resistance of Ni-Based WC Coating by Ultra-High Speed Laser Cladding

Microstructures and Properties of Laser-Clad in Situ Particle Reinforced Ni-Base Composite Coating on 55mn Steel

Microstructure and Mechanical Properties of Ni-Based Alloy Composite Coating on Cr12MoV by Laser Cladding

Investigation on the Microstructure Evolution and Properties of a Novel In-Situ Fiber Phase-Reinforced Nickel Composite Coating Deposited by Wide-Band Laser

Microstructure and wear resistance of laser cladding Ni-WC coating on aluminum alloy

High-Speed Laser Cladded Ni-Based WC Coatings: Microstructure, Friction-Wear Property and Wear Mechanism

Microstructure and Wear Properties Under Dry Sliding for Micro-nano WC Composite Coatings Prepared by Laser Cladding

Investigation on the Ni60-WC composite coatings deposited by extreme-high-speed laser-induction hybrid cladding technology: Forming characteristics, microstructure and wear behaviors

Microstructure, interface characteristics and tribological properties of laser cladded NiCrBSi-WC coatings on PH 13-8 Mo steel

Microstructure and Sliding Wear Resistance of Laser Cladded WC/Ni Composite Coatings with Different Contents of WC Particle

Microstructure and Properties of WC Reinforced Ni-based Composite Coatings with Y2O3 Addition on Titanium Alloy by Laser Cladding

Experimental Study on the Microstructure and Tribological Properties of Laser-Clad Ni60-WC Composite Coatings

Study of Design and Microstructure Properties of Laser Clad Multiphase Coupled Nickel-Based Self-Lubricating Coatings