Abstract:In this study, red mud was used as the main raw material to prepare polyaluminum-ferric chloride (PCFA) with high added value. The effects of the liquid–solid ratio, reaction temperature, reaction time, hydrochloric acid concentration during acid leaching, polymerization time, OH − /Fe molar ratio, and polymerization temperature on the preparation of PCFA were investigated and determined by conducting single-factor optimization experiments under optimal preparation conditions. Characterization results show that the surface of the PCFA flocculant has compact and dense porosity and a dense sheet-like structure, and PCFA contains hydroxyl-bridged iron–aluminum polymers. When the settling time was 30 min, the stirring intensity was 200 rpm; the initial concentration of Nano-titanium dioxide(TiO 2 -NPs) was 30 mg·L −1 ; the pH value was 7.0; the dosage of PCFA was 25 mg·L −1 , and the optimum removal rates of TiO 2 -NPs and turbidity were 84.8% and 81.3%, respectively. The flocs produced by PCFA treatment of TiO 2 -NPs were large and dense. Under optimal flocculation conditions, the average particle size of PCFA-TiO 2 -NP flocs was 2.98 μm, and the fractal dimension was 1.66. Based on the abovementioned flocculation experimental data, a Grey correlation method was established to evaluate the degree of correlation among factors such as ionic strength, settling time, stirring strength, kaolin concentration, initial concentration, reaction pH value, and dosage and the performance of PCFA coagulation to remove TiO 2 -NP-containing wastewater. In the reaction system of the PCFA coagulation of TiO 2 -NPs, the dosage is the most important factor.

WATER PURIFICATION BY HIGH-CONCENTRATION POLYFERRIC CHLORIDE (PFC) COAGULANT

[Removal of Turbidity and Effect of Humic Acid in Flocculation by Polyferric Chloride].

An enhanced coagulation using ferric chloride and poly-ferric chloride coagulant assisted by polyamidine: Performance and mechanisms

Landfill Leachate Pretreatment by Coagulation–flocculation Process Using Iron-Based Coagulants: Optimization by Response Surface Methodology

Preparation of poly ferric sulfate and the application in micro-polluted raw water treatment

Electroplating Wastewater Treatment by Polyaluminum Ferric Chloride

Insight into Control Mechanism of Polymeric Ferric Titanium Composite Coagulant on Membrane Fouling: Role of Natural Organic Matters

Development of a Polyaluminum Ferric Titanium Chloride for Phosphorous Removal in Water

Multiple Response Optimization of the Coagulation Process for Upgrading the Quality of Effluent from Municipal Wastewater Treatment Plant

Characterization and coagulation–flocculation performance of a composite coagulant: poly-ferric-aluminum-silicate-sulfate

Study on preparation,characterization and application of nano-sized polyferric sulfate coagulant

A Comparative Study of Ferrous, Ferric and Ferrate Pretreatment for Ceramic Membrane Fouling Alleviation in Reclaimed Water Treatment

Study on the preparation of polysilicate ferric flocculant and its treatment of high turbidity tailings water

Enhanced Coagulation of Low-Turbidity Micro-Polluted Surface Water: Properties and Optimization.

Application of a green coagulant with PACl in efficient purification of turbid water and its mechanism study

The Optimal Experimental Research on the Fluoride Removal from Efficient-Whirling Clarifier

Comparison of flocculant aids as pretreatment reagent for membrane filtration process by fingerprint analysis of organic matters in secondary effluent

Flocculation Performance of PCFA Composite Coagulant for Removing Nanoparticles

Study on the pretreatment of printing & dyeing wastewater with composite polyaluminum ferric flocculants

Removal of Perfluorooctanoate from Surface Water by Polyaluminium Chloride Coagulation

A membrane fouling control strategy based on a combination of pre-treatment mitigation and in-situ membrane surface regulation using a composite coagulant