Abstract:Objective A group of total hip arthroplasties were followed up radiologically to in ves-tigate the relationship of the cup ab duction angle with the extent of wearing and its direction and the effects of the cup abduction angle on the stability of hip joint.Methods A series of 32hip joints(30patients)were followed up routinely.The average f ollow-up period was 4.2years.The cu p abduction angle was measured,and the sagittal displacement of fem oral head to acetabulum was also exam ined to determine the direction and degree of linear polyethylene wear.The direction and magnitude of wear were decided by measuring femoral head penetration into the polyethylene liner.A new method of computer assisted two dimensional wear mea-surement was employed in this study.The results were statistically analyzed,with a P value less than 0.05indicating significant difference.Results There were no evidences of component loosening and clinical failure among the 32hips at a latest f ollow-up.The angle between the axis femoral component and femoral shaft in all of the patients was less than 3d egrees.The average amount of linear wear was 0.81mm,and the wear rate was 0.18mm per year.The average cup abduction angle was 54.5degrees,the wear direction was?6.93degrees superior-laterally.Wear d irection had a negative correlation with cup abduction angle by linear re-gression analysis;it meaned that th e direction of wear turning from superior-medial to superior-lateral gradually along with the increasing of cup abduction angle.In the cup abduction angle of more than 55degrees,the wear direction mostly orientated superior-laterally.However,no correlation of linear wear amount with wear di rec-tion or cup abduction angle was found in linear regression analysis.Conclusion Wear direction and cup abduction angle is negatively corre lated.The wear direction points mostly superior-laterally with cup abd uction angle over 55degrees,which could re sult in uneven stress distribution a nd greater stress concentration sup e-rior-laterally,consequently increase of wear;meanwhile,if the cup is too vertical,the risk of impingemen t and dislocation increases.The study shows that acetabular components with cup abduction angle over 55de-grees should be avoided in order to ma intain hip stability and desirable r ange of motion.

The relation between the concertration of OPG and wear debris accumulation

Measurement of polyethylene wear and its clinical significance in total hip arthroplasty

STUDY ON THE EFFECT OF ARTIFICIAL HIP JOINT REPLACEMENT ON BLOOD VESSEL CECs, EPCs AND SERUM OSTEOCALCIN OF PATIENTS WITH TRAUMATIC OSTEONECROSIS OF THE FEMORAL HEAD

Isolation and Analysis of Wear Particles from Severe Osteolytic Tissue Around Acetabular Implant

Roles of OPG and OPGL in Periprosthetic Osteolysis

Distribution and migration of wear debris in prosthesis

Wear of polyethylene lining and histological profiles of periprosthetic tissue in total hip arthroplasty

The Relationship of Wearing with the Abduction Angle of the Acetabulum in Total Hip Arthroplasty

Comparative wear and wear debris under three different counterface conditions of crosslinked and non-crosslinked ultra high molecular weight polyethylene

Comparison of wear on articular cartilage by titanium alloy, ultra-high-molecular-weight polyethylene, and carbon fibre reinforced polyether-ether-ketone: A pilot study

Nano wear particles and the periprosthetic microenvironment in aseptic loosening induced osteolysis following joint arthroplasty

Tribo-biological deposits on the articulating surfaces of metal-on-polyethylene total hip implants retrieved from patients

Comparison of osteolysis around 3 different cement restrictors in total hip arthroplasty

Macrophage inhibits the osteogenesis of fibroblasts in ultrahigh molecular weight polyethylene (UHMWPE) wear particle-induced osteolysis

Histochemical identification of wear debris released by alumina-on-alumina hip prostheses in the periprosthetic tissues

Characterization of wear debris in total elbow arthroplasty

Effect of Progressive Wear on the Contact Mechanics of Hip Replacements – Does the Realistic Surface Profile Matter?

Biological mechanism of periprosthetic osteolysis after total hip arthroplasty

Carbon Fiber Composite for Acetabular Prosthesis-Fabrication,Wear and Biocompatibility

Polyethylene wear and osteolysis in H/G cementless total hip arthroplasty]

Effect of different loads on wear mechanisms of polyether-ether-ketone in normal saline and debris-isolating method