Abstract:Background: Impressions that maintain their dimensional stability after autoclaving effectively control cross-infection and contamination resulting from a patient's oral secretions. Purpose: The study aimed to assess the dimensional stability of autoclavable polyvinyl siloxanes after disinfection and sterilization. Methods: A stainless steel metal model containing three full veneer crown preparations was fabricated according to ANSI/ADA specification No. 19. Reference grooves were established on the occlusal and axial surfaces of the abutments for accurate measurements. Forty impressions were created from the master model using single-step impression technique monophase polyvinyl siloxane material (AFFINIS, Coltene/Whaledent, Altstatten, Switzerland). The impressions were categorized into four groups: Group A (control, ten untreated impressions), Group B (ten disinfected impressions with 5.25 % sodium hypochlorite [NaOCl]), Group C (ten disinfected impressions with 2 % glutaraldehyde), and Group D (ten autoclaved impressions at 134 °C for 18 min). Subsequently, stone casts were produced using type IV gypsum products (Gelstone R, BK Giulini Chemie, Ludwigshafen/Rh., Germany). The dimensional accuracy of the obtained casts was assessed by measuring the inter-abutment measurements (between the abutments) and the intra-abutment measurements (diameter and height of the abutments). These measurements were performed using a universal measuring microscope (Olympus stereomicroscope B061 Imaging Corp. Tokyo, Japan) with a precision of 0.001 mm. The dimensions of the stone casts from the study groups were then compared to those of the control group. Data analysis was performed using a one-way ANOVA with a significance level of α = 0.05. Results: AFFINIS impressions subjected to chemical disinfection in 5.25 % NaOCl and 2 % glutaraldehyde with different immersion times showed slight expansion in the intra- and inter-abutment measurements. The impressions autoclaved at 134 °C for 18 min showed slight shrinkage in the intra- and inter-abutment measurements. The dimensional change was statistically non-significant, and the percent of dimensional changes within the experimental groups was within the clinically accepted limit (α < 0.5). Conclusion: AFFINIS polyvinyl siloxanes retain dimensional stability suitable for clinical use when subjected to chemical disinfection and steam autoclaving.

The Effect of Different Disinfectants on Wettability of the Modified Silicone Rubber Impressions

The Effect of Glutaral Disinfectant Solution on Wettability of the 6 Elastomer Impression Materials

[The Effect of Disinfection on Dimension Stability of Impressions].

Effect of different disinfection methods on surface free energy and Shore hardness of carbon ion-implanted silicone rubber

Effect of Different Disinfecting Methods on the Accuracy of Agar-Alginate Impression

Evaluation of the Effect of Immersion Disinfection on the Dimensional Stability of Alginate Impressions

The effect of glutaraldehyde disinfectant on the dimension stability of four high polymer impression materials

Effects of a new disinfectants(IMPRESEPT) on dimensional accuracy of impression materials

Disinfection Efficacy of Sodium Hypochlorite and Glutaraldehyde and Their Effects on the Dimensional Stability and Surface Properties of Dental Impressions: a Systematic Review

Wettability study of hydrophilic silicone oral impression materials

The effect of Soniclized Electrolyzed Oxidizing Water disinfection procedure on the dimensional accuracy of dental impressions

Effect of Disinfectant with Benzethon Chloramine and Isopropanol As Main Active Ingredients on the Accuracy of Dental Impression

[Effect of different kinds of gingival retraction agents on the polymerization inhibition of polyvinyl siloxane impression materials].

Effect of chemical disinfection on surface detail reproduction and dimensional stability of a new vinyl polyether silicone elastomeric impression material

[Influence of Autoclave Sterilization on Dimensional Stability and Detail Reproduction of 5 Additional Silicone Impression Materials].

Effects of Liquids Immersion and Drying on the Surface Properties of HTV Silicone Rubber: Part I-contact Angle and Surface Chemical Properties

Static and Dynamic Evaluations of the Wettability of Commercial Vinyl Polysiloxane Impression Materials for Artificial Saliva

Impression Disinfection and Its Effect on Dimensional Accuracy and Surface Detail in the Times of COVID-19: An In Vitro Study

Comparative analysis of dimensional changes in autoclavable polyvinyl siloxane (PVS) impressions under various Sterilization/Disinfection Protocols: A randomized controlled trial

Effect of Different Cleaning Methods on Bond Strength and Surface Wettability of High Translucency Zirconia

Effect of Disinfection on Tensile Strength and Rupture Elongation of Maxillofacial Silicone Reinforced with Nano-Filler Particles