Abstract:Surface modification, sputtering erosion and deuterium (D) retention were investigated of tungsten (W) and W-1 wt.% La2O3 (WL10) that were exposed to pure D plasma and D plasma with different impurities (He, N2, Ar). After the plasma exposure, the surface of WL10 is covered by blisters with various shapes, and their size and density increase with D fluence. When the fluence was higher than 8.6 x 1024 D m-2, the blister rupturing occurred causing a partially-and/or fully-opened lid features. The phase interface between La2O3 grains and W matrix was served as the nucleation sites for blistering and large-scale crack propagation near the surface. Small blisters were preferentially appeared on the grains with surface orientation of nearly (111) and that originated from the intra-granular crack at depths much closer to the sample surface. Micro-sized pits were formed on the WL10 surface after exposure to high fluence plasma, which was due to a higher sputtering rate of La2O3 grains during plasma exposure. For both materials, seeding He in D plasma can effectively inhibit the blister formation, and most serious blistering occurs with N seeding in D plasma. When exposed to Ar + D plasma, sparse small blisters were visible and most of blisters were ruptured for W, whereas there are some big blisters with long strip shape for WL10. The difference in blistering behavior between W and WL10 was attributed to the differences in microstructure, composition as well as ductility due to the presence of La2O3 phases. The sputtering yields increased slightly with He seeding in D plasma. N2 and Ar seeding in D plasma leaded to a significant increase in sputtering yields. As compared to the W, the WL10 exhibits a better sputtering erosion resistance in terms of the sputtering yield. The D retention in WL10 increases with D fluence and that was equal to or lower than that in W when exposed to the same conditions.(c) 2022 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.

Influence of Lah2 on Oxidation Characteristics and Irradiation Melting Characteristics of A Tungsten Coating Fabricated by Atmospheric Plasma Spraying

Lanthanum Hydride Doped Tungsten-Based Coating Fabricated by Supersonic Atmospheric Plasma Spraying

Selective laser melting of lanthanum oxide-reinforced tungsten composites: microstructure and mechanical properties

Microstructure and Tribological Properties of Laser-Remelted Ni-Based WC Coatings Obtained by Plasma Spraying

Effect of La2o3 on Resistance to High-Temperature Oxidation of Laser Clad Ferrite-Based Alloy Coatings

Ablation Behavior of Plasma-Sprayed La1-xSrxTiO3+δ Coating Irradiated by High-Intensity Continuous Laser

Comparison of W–TiC Composite Coatings Fabricated by Atmospheric Plasma Spraying and Supersonic Atmospheric Plasma Spraying

Influence of impurity gas seeding into deuterium plasma on the surface modification, sputtering erosion and deuterium retention in W and W-La2O3 alloy

Microstructure and Mechanical Property Regulation of Plasma-Sprayed High-Entropy (la0.2nd0.2sm0.2eu0.2gd0.2)2zr2o7 Thick Coatings

Effects of Tungsten and Laser Re-Melting on the Properties of Hastelloy C22 Coating

Effect of La2O3 on the microstructure and wear resistance of laser clad nickel-based alloy coatings

Microstructure and mechanical properties of W-Ta-V-Cr high-entropy alloy coatings by double glow plasma surface alloying

Effect of La2o3 on Corrosion Resistance of Laser Clad Ferrite-Based Alloy Coatings

Effect of La<sub>2</sub>O<sub>3</sub> on the Microstructure and Properties of Laser Cladding Fe-based JG-8 Alloy

Microstructure, Wear Behaviour and Laser Ablation Behaviour of Double Glow Plasma Alloyed Ta-W Coating

Effect of Heat Treatment on LaTi<sub>2</sub>Al<sub>9</sub>O<sub>19</sub>-Zr<sub>0.92</sub>Y<sub>0.08 </sub>O<sub>1.96</sub> Composite Coating Powders by Air Plasma Spraying

Investigation of the Enhancement Mechanism of Electrochemically Deposited Ni–Co–W Coatings via Laser Irradiation: Effect of W Contents on Corrosion Resistance

Microstructure, phase constitution and mechanical properties of WC-Cr3C2-CoNiLa coatings fabricated by using HVOF spraying core-shell powder

Effects of laser remelting on microstructure and tribological properties of plasma–sprayed Fe45Mn35Co10Cr10 high–entropy alloy coating

Prolonged thermal durability of plasma-sprayed lanthanum hexaluminate thermal barrier coating by optimizing crystallinity

Infrared radiation and thermal cyclic performance of a high-entropy rare-earth hexaaluminate coating prepared by atmospheric plasma spraying