Abstract:Direct ink writing (DIW) of aerogels has great potential in designing novel three-dimensional (3D) multifunctional materials with hierarchical structures ranging from the nanoscale to the macroscopic scale. In this paper, pure aerogels composed of inorganics, strongly cross-linking organics, and weakly cross-linking organics were directly written via the precise control of the gelation degree without using any additives. The rheological properties of a resorcinol–formaldehyde aerogel-based sol–gel ink (marked as RA ink) were measured at different reaction times to determine the suitable printable range (G′LVR: several 103 Pa) that ensures its good print fidelity. In addition, the rheological evolution of the RA ink during the sol–gel process and under different shear stresses was studied. The correlation of relevant parameters was established according to the Hagen–Poiseuille model. Other typical aerogel-based sol–gel inks including a silica aerogel-based sol–gel ink (SA ink) and a polyimide aerogel-based sol–gel ink (PA ink) for DIW were also demonstrated. Finally, water evaporation experiments were carried out using a 3D-printed carbonized resorcinol–formaldehyde aerogel (CA) to further exhibit the potential applications of this novel technology in solar steam generation. The evaporation rate (1.57 kg m–2 h–1) and efficiency (88.38%) of 3D-printed CA were higher than those of bulk CA (1.21 kg m–2 h–1 and 69.82%). This paper systematically studies the control of DIW parameters for aerogel-based sol–gel inks and shows a potential application in high-efficiency 3D-printed evaporators.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acs.langmuir.0c03312?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acs.langmuir.0c03312</a>.Rheological behaviors and thixotropic behaviors of RA inks (Figure S1); rheological behaviors of the SA ink and the PA ink (Figure S2); rapid solidification of the PA ink once it met water (Figure S3); Herschel–Buckley model for RA inks (Figure S4); study of relevant parameters in DIW (Figure S5); extrusion experiments for dextrin (Figure S6); extrusion experiments for RA inks (Figure S7); 3D-printed hydrogels using the RA ink, SA ink, and PA ink (Figure S8); TG-DSC tests for 3D-printed aerogels (Figure S9); uniaxial compression–decompression test for 3D-printed aerogels (Figure S10); derivation of the correlation of the relevant parameters; filament widths at varied applied pressures and writing speeds (Table S1); filament widths at varied heights of the needle to the substrate (Table S2); pressure value, maximum shear stresses, and yield stresses for dextrin and RA inks (Table S3); detailed parameters of bulk CA and 3D-printed CAs (Table S4); and water evaporation data of 3D-printed CAs, bulk CA, and pure water (Table S5).This article has not yet been cited by other publications.

Suspensions Designed for Direct Ink Writing

Embedded Extrusion Printing in Yield-Stress-fluid Baths

A Fully Resolved Smoothed Particle Hydrodynamics-Discrete Element Method Study of the Rheology of Suspensions: the Role of Inertia and Grain Shape

Direct Ink Writing Based 4D Printing of Materials and Their Applications

Additive manufacturing solidification methodologies for ink formulation

Direct-ink-writing (DIW) 3D printing functional composite materials based on supra-molecular interaction

Direct-writing Construction of Layered Meshes from Nanoparticles-Vaseline Composite Inks: Rheological Properties and Structures

Go with the flow: Rheological requirements for direct ink write printability

Recent Development and Applications of Advanced Materials via Direct Ink Writing

Direct Ink Writing of Special-Shaped Structures Based on Tio2 Inks

A novel experimental approach to quantitatively evaluate the printability of inks in 3D printing using two criteria

Direct Ink Writing: A 3D Printing Technology for Diverse Materials

Versatile Direct Writing of Aerogel-Based Sol–Gel Inks

Computationally Guided DIW Technology to Enable Robust Printing of Inks with Evolving Rheological Properties

Design of a Shaping System for Stereolithography with High Solid Loading Ceramic Suspensions

Embedded Direct Ink Writing 3D Printing of UV Curable Resin/Sepiolite Composites with Nano Orientation

Direct Ink Writing of Mineral Materials: A review

3D printing of Pickering emulsions, Pickering foams and capillary suspensions - A review of stabilization, rheology and applications

Spreading of Low-viscosity Ink Filaments Driven by Bath Viscoelasticity in Embedded Printing

Development and Characterizations of Novel Aqueous-Based Ceramic Inks for Inkjet Printing

Advective Assembler‐Enhanced Support Bath Rotational Direct Ink Writing