Abstract:For parts of machines and equipment operating under the influence of aggressive media, abrasive, high temperatures, the creation of a hard, wear-resistant surface is an urgent task. Cobalt is used as a binder to create hard alloy materials that work under these conditions. It was of interest to evaluate the possibility of using cobalt as an additive in complex thermal diffusion chromium plating of structural steel. The article describes the features of thermal diffusion saturation of steel X35CrNi2-3 with chromium and cobalt at a temperature of 1000°C. A technique for analyzing the obtained coating is presented, based on the possibilities of X-ray spectral microanalysis of the diffusion layer on transverse microsections of the obtained samples. The elemental composition of the diffusion layer was monitored using the JEOL JSM-6460 LV universal scanning (scanning) electron microscope. The microstructure was studied using the optical metallographic microscope Axio Observer D1.m. The X-ray phase analysis was carried out with the Rigaku Ultima IV diffractometer. The hardness measurement was carried out with the FM-800 microhardness tester at a load of 50 g. Data were obtained on the distribution of chromium and cobalt in the surface layer of steel. It is shown that the resulting thermal diffusion coating consists mainly of a substitutional solid solution based on Cr‒Fe‒Co with bcc lattice and chromium carbides. The average diffusion coefficients of chromium in the α-phase of chromium were determined to be DCr = 3,22·10‒15 м2/с; in the γ-phase of iron DCr = 9,41·10‒15 м2/с. The diffusion coefficient of cobalt in the γ-phase of iron DCo = 7,89·10‒15 м2/с. The depth of the outer coating on the sample was about 15–20 μm, the depth of the diffusion layer of chromium in the base metal was about 70 μm, and that of cobalt was about 40 μm. The maximum hardness of the outer surface layer was 1740 HV, the diffusion layer in the base metal was 900–560 HV, and the base metal was about 510 HV.

Diffusion Kinetics of Chromium in a Novel Super304H Stainless Steel

Study on Diffusion Kinetics and Law of Chromium on the Surface of Low-Carbon Steel

Critical Temperature Determination of Detectable Cr Diffusion Enhancement by Nanostructure Through Structural Evolution Analysis of the Oxide Films at 25–450 °C on 304 Stainless Steel

THE CHROMIUM AND COBALT DISTRIBUTION IN THE DIFFUSION LAYER OF STEEL X35CrNi2-3 DURING THERMОDIFFUSION SATURATION

Effect of Chromium and Water Vapor of Low Carbon Steel on Oxidation Behavior at 1050 °C

Study on impact of Cr and Mo on diffusion of H in 2.25Cr1Mo steel using first-principle calculations

A High-Resolution Study of the Different Surface State Effects on the Corrosion Behaviors of a Ferritic Steel and an Austenitic Steel in Supercritical Water

Study of Fe Diffusion in Cr2O3 by Secondary Ion Mass Spectrometry

Chromium Diffusion Coating on an ODS Ferritic-Martensitic Steel and Its Oxidation Behavior in Air and Steam Environments

Chromium Gradient Stainless Steels with Simultaneous High Strength, Ductility, and Corrosion-resistant: In-depth Study of Continuous Hardening Mechanisms

Influence of the composition of the cumulative lattice during thermal diffusion chromiing on the depth of the diffusion layer

Evaluation of Intergranular Corrosion Susceptibility of 11cr Ferritic Stainless Steel by Dl-Epr Method

Microstructural understanding of the oxidation and inter-diffusion behavior of Cr-coated Alloy 800H in supercritical water

Precipitation Kinetics of M 23 C 6 Carbides in the Super304H Austenitic Heat-Resistant Steel

Growth Kinetics and Microstructure of Composite Coatings on H13 by Thermal Reactive Diffusion

Interdiffusion of Cr, Mo, and W in Iron

Temperature-dependent evolution mechanism of interface microstructure between gradient MCrAlY coatings and nickel-based superalloy

Magnetism Variance Analysis of Super304H Austenitic Stainless Steel after Service

Chromium Depletion in a Ni-30Cr Alloy During High-Temperature Oxidation

In Situ Observation of Phase Transformation and Structure Evolution of a 12 Pct Cr Ferritic Stainless Steel

Coarsening and Hardening Behaviors of Cu-Rich Precipitates in Super304H Austenitic Steel