Abstract:Waterjet-assisted laser drilling technology facilitates the fabrication of high-quality micro-holes by utilizing the collaborative benefits of waterjets and lasers. In this study, the coaxial waterjet-assisted laser drilling (CWALD) technique was employed to improve the properties of micro-holes during femtosecond laser drilling. Based on computational fluid dynamics (CFD) simulations, the stability of the waterjet was initially verified by optimizing the structure of the watercourse and nozzle shape in the CWALD device. Furthermore, a comparative experiment between laser direct drilling (LDD) and CWALD revealed that while CWALD can produce well-rounded micro-holes with a high aspect ratio, it exhibits lower efficiency and results in a larger heat-affected zone (HAZ). To address these drawbacks associated with CWALD, a two-step coaxial waterjet-assisted composite laser drilling (TS-CWALD) method was proposed. TS-CWALD involves applying CWALD for secondary modification of micro-hole shape following LDD with punching. This modification process is pivotal for enhancing drilling accuracy but requires consideration of multiple parameters. For this purpose, regression models were established for the inlet diameter, outlet diameter, and taper; response surface methodology was then employed to optimize these parameters. Subsequently, interactive effects analysis was conducted on different responses based on laser pulse energy, frequency, modification speed, and number of modification cycles. The adequacy of the developed models was subsequently verified using analysis of variance methods. Finally, the successful fabrication of a film hole with an inlet diameter of 205 μm and an outlet diameter of 200 μm, featuring a taper of only 0.2°, was achieved ultimately through meticulous parameter optimization. Furthermore, the micro-hole retained a minimal HAZ. The optimized parameters encompassed a pulse energy of 20.6 μJ, frequency of 127 kHz, modification speed of 3 mm/s, and shape modification carried out over 335 cycles.

Optimization of Micropipette Fabrication by Laser Micromachining for Application in an Ultrafine Atmospheric Pressure Plasma Jet Using Response Surface Methodology

Optimized Fabrication of Micropipette Using Laser Micromachining Process and Application in Functional Electrical Stimulation of Muscle Tissue

Mass Fabrication of Microholes in Aviation Kerosene Filters Using the Back-water-assisted Picosecond Laser Drilling Technique

Experimental Research on CO_2 Laser Direct-writing Machining PMMA Microchannel

Surface microfabrication using coaxial waterjet assisted laser-induced plasma micromachining

Experimental Investigation and Optimization of Laser Induced Plasma Micromachining Using Flowing Water

Investigation of Overflow-Water-Assisted Femtosecond Laser-Induced Plasma Modulation of Microchannel Morphology

Experimental investigation and optimization of modification during coaxial waterjet-assisted femtosecond laser drilling

Optimization of Micromilled Channels for Microfluidic Applications Using Gas-Blowing-assisted PDMS Coating

Comparative Assessment of Picosecond Laser Induced Plasma Micromachining Using Still and Flowing Water

New Method of Continuous-Wave Laser Ablation for Processing Microgroove with Variable Cross-Section

Experimental Research on Water-Jet Guided Laser Processing

A Facile Approach for Rapid Prototyping of Microneedle Molds, Microwells and Micro-Through-Holes in Various Substrate Materials Using CO2 Laser Drilling

Direct And All-Dry Microfabrication Of Ultramicroelectrode Based On Cold Atmospheric Microplasma Jet

Laser-Induced Bubble Dynamics Optimization for High-Aspect-Ratio 3D Micro-Fluidic Channels Fabrication

Optimization and Test of a Ring-Ring Typed Atmospheric Pressure Plasma Jet for Optical Fabrication

Influence of Pulse Energy on Machining Characteristics in Laser Induced Plasma Micro-Machining

Laser Machining at High ∼PW/cm2 Intensity and High Throughput

Advances of Short and Ultrashort Pulse Laser Induced Plasma Micromachining

Experimental Research and Optimization of Ti-6Al-4V Alloy Microgroove Machining Based on Waterjet-Guided High-Power Laser

Multiplexed electrospray emitters fabricated by rapid laser micromachining