Abstract:Introduction Solid state batteries offer increased safety, high voltage stability, and simpler electrolyte chemistry than organic electrolytes. Their inherent protection from dendrite growth gives the capability to use metallic lithium anodes. Recent advances have improved conductivity to within an order of magnitude of organic electrolytes at room temperature. However, interfacial resistance between electrodes and the electrolyte remains a pressing concern. In a typical planar battery, this high resistance per area is magnified by low interfacial surface area. Elemental composition has a significant effect on the conductivity of a garnet electrolyte. The conductivity of the garnet fluctuates an order of magnitude based on a lithium stoichiometry of 6 to 7 in the Li7-xLa3Zr2-xTaxO12series. It has also been demonstrated that aluminium composition at the grain boundaries associated with higher temperature sintering increases conductivity. It stands to reason lithium activity extremes at the electrode interfaces effects would cause local variations in electrolyte composition and affect the conductivity. This study aims to address some of these concerns using a systematic study of the anode-electrolyte interface and the cathode-electrolyte interface. We investigate the elemental composition of the interface, as well as the effect of greatly increased surface area through a highly microporous electrolyte scaffold containing the cathode and anode material. Experimental Procedure Li7La3Zr2O12 garnet was produced in a conventional solid state method. 10% excess LiOH-H2O and stoichiometric amounts of La2O3 and ZrO2were ball milled in ethanol for 24 hours. The milled materials were added to an alumina crucible, calcined at 900 ºC for 4 hours, and milled again. A colloidal deposition of this slurry is prepared with polyvinyl butyral (PVB), benzyl butyl phthalate (BBP), and Solsperse dispersant in ethanol. Calcined powder is added to toluene and ethanol solvents with a binder system containing PVB, BBP, and menhaden fish oil as a dispersant. This preparation is milled for two days, then degassed in preparation for tape-casting. After tape-casting, tapes are drop-coated with the colloidal slurry and another tape is applied on top. This structure is held at 500ºC for 1 hour to burn off binders then heated to 1100 ºC for 1 hour. This produces a three layer porous-dense-porous scaffold of electrolyte that will maintain electronic isolation between electrodes. Symmetric cells with two cathodes are produced by infiltrating a glycine/metal-nitrate solution into the pores of each side and combusting. For two-anode symmetric cells, lithium is lightly pressed into both sides at 350 ºC. Electrochemical impedance spectroscopy was performed between room temperature and 300 ºC using a 10 mV amplitude between 10 MHz and 100 mHz. Electron energy loss spectroscopy was performed on a 2100F TEM equipped with a Gatan Tridiem post-it column energy filter. Results Figure 1 shows a cross section of a lithium-penetrated Li-garnet scaffold showing the fracture plane of the garnet(light) fully coated by the lithium (dark). Figure 2 shows the Nyquist plot of a full cell made with a lithium-penetrated scaffold. The bulk conductivity shown in the inset is fairly low at 20 Ω compared to the 1000 Ω overall cell impedance.

Chemical Compatibility Between Garnet-Like Solid State Electrolyte Li6.75la3zr1.75ta0.25o12 and Major Commercial Lithium Battery Cathode Materials

LiCoO2 Sintering Aid Towards Cathode-Interface-enhanced Garnet Electrolytes

Enhanced Performance of Li6.4La3Zr1.4Ta0.6O12 Solid Electrolyte by the Regulation of Grain and Grain Boundary Phases.

Liquid sintering of garnet electrolytes by lithium germanate: Properties and interfacial performance with lithium anode

Effect of Microstructure and Elemental Composition on Electrode Interfacial Impedance of Li7La3Zr2O12-based Batteries

Low-Temperature Sintering of a Garnet-Type Li6.5La3Zr1.5Ta0.5O12 Solid Electrolyte and an All-Solid-State Lithium-Ion Battery.

Enhanced Performance of Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 Solid Electrolyte by the Regulation of Grain and Grain Boundary Phases

Unveiling the roles of alumina as a sintering aid in Li‐Garnet solid electrolyte

Electrochemical Properties and Structural Stability of Ga- and Y- Co-Doping in Li7La3Zr2O12 Ceramic Electrolytes for Lithium-Ion Batteries

Probing Alkaline-Earth-Doped Garnet-Type Li 7 La 2.75 A 0.25 Zr 1.75 M 0.25 O 12 (A = Ca, Sr, Ba; M = Nb, Ta) Electrolytes for All-Solid-State Li Metal Batteries

Submicron-Sized Nb-Doped Lithium Garnet for High Ionic Conductivity Solid Electrolyte and Performance of Quasi-Solid-State Lithium Battery

Inhibiting Formation and Reduction of Li2 CO3 to LiCx at Grain Boundaries in Garnet Electrolytes to Prevent Li Penetration.

Excess Lithium Salt Functions More Than Compensating for Lithium Loss when Synthesizing Li6.5La3Ta0.5Zr1.5O12 in Alumina Crucible

About the Compatibility between High Voltage Spinel Cathode Materials and Solid Oxide Electrolytes as a Function of Temperature

Effect of Sintering Temperature and Holding Time on Ionic Conductivity for Li6.4La3Zr1.4Ta0.6O12 Electrolyte

Effect of Dual Doping on the Structure and Performance of Garnet-Type Li7La3Zr2O12 Ceramic Electrolytes for Solid-State Lithium-Ion Batteries

Bonding Lithium Metal with Garnet Electrolyte by Interfacial Lithiophobicity/Lithiophilicity Transition Mechanism over 380 °C

On the Interfacial Properties of the Garnet-Type Electrolyte Ceramic Pellets of Cubic Li6.4la3zr1.4ta0.6o12: A Comprehensive Promotion Mechanism by the Sintering Additive of Li-Ion Conducting Licl

Inhibiting Formation and Reduction of Li2CO3 to LiCx at Grain Boundaries in Garnet Electrolytes to Prevent Li Penetration

Negating Interfacial Impedance in Garnet-Based Solid-State Li Metal Batteries

Sintering Behavior of Garnet‐type Li6.4La3Zr1.4Ta0.6O12 in Li2CO3 Atmosphere and Its Electrochemical Property