All Polymer Solar Cells with Diketopyrrolopyrrole-Polymers As Electron Donor and A Naphthalenediimide-Polymer As Electron Acceptor

Cheng Li,Andong Zhang,Zhaowei Wang,Feng Liu,Yi Zhou,Thomas P. Russell,Yongfang Li,Weiwei Li

DOI: https://doi.org/10.1039/c6ra03681c

IF: 4.036

2016-01-01

RSC Advances

Abstract:Diketopyrrolopyrrole-polymers and N2200 were found to be highly miscible, which induced low efficiencies in all-polymer solar cells.

What problem does this paper attempt to address?

Naphthalenediimide-based N-Type Polymer Acceptors with Pendant Twisted Perylenediimide Units for All-Polymer Solar Cells

Zhaojing Wang,Manjun Xiao,Xi Liu,Baitian He,Xiye Yang,Yuan Li,Junbiao Peng,Fei Huang,Yong Cao

DOI: https://doi.org/10.1016/j.polymer.2018.10.062

IF: 4.6

2018-01-01

Polymer

Abstract:Polymeric acceptor based all-polymer solar cells have attracted wide interest due to their excellent mechanical properties. In order to combine the advantages of both the polymer and perylenediimide-based small-molecular acceptors, we designed and prepared a series of random copolymers via linking perylenediimide to the polymeric backbone of (naphthalenediimide/quinoxaline)-thieno[3,2-b]thiophene, which were successfully applied as polymer acceptors in solar cells. The effects of the pendant perylenediimide on the optical, electrochemical and photovoltaic performance were tuned via varying ratios of (quinoxaline-perylenediimide2) and naphthalenediimide. Atomic-force microscopic images showed that all random copolymers exhibited significantly improved miscibility with donor compared with an alternating copolymer reference, which coincided with the higher electron mobility measured by the space charge limited current method. The all-polymer solar cell based on the polymeric acceptor with high perylenediimide content achieved a power conversion efficiency of 4.81%. Although there is minimal conjugation between the perylenediimides and main chains, perylenediimides can also contribute to photocurrent generation.
Copolymers of perylene diimide with dithienothiophene and dithienopyrrole as electron-transport materials for all-polymer solar cells and field-effect transistors

Xiaowei Zhan,Zhan'ao Tan,Erjun Zhou,Yongfang Li,Rajneesh Misra,Adrian Grant,Benoit Domercq,Xiao-Hong Zhang,Zesheng An,Xuan Zhang,Stephen Barlow,Bernard Kippelen,Seth R. Marder

DOI: https://doi.org/10.1039/b907163f

2009-01-01

Journal of Materials Chemistry

Abstract:Electron-accepting solution-processable conjugated polymers consisting of perylene diimide moieties alternating with dithienothiophene, oligo(dithienothiophene), or N-dodecyl dithienopyrrole units have been synthesized. All these polymers possess excellent thermal stability with decomposition temperatures over 400 °C. The glass-transition temperatures vary from 155 to 263 °C. These polymers show broad absorption extending from 250 to 900 nm with electrochemical and optical bandgaps as low as 1.4 eV; the maximum absorbance increases and the bandgap decreases with increasing the conjugation length of oligo(dithienothiophene), while the bandgap can also be decreased by the replacement of dithienothiophene by dithienopyrrole. The electrochemical onset reduction potentials range from −0.8 to −1.0 V vs. ferrocenium/ferrocene, suggesting that the electron affinities are essentially unaffected by the specific choice of donor moiety, while the onset oxidation potentials (+0.6 to +1.0 V) are a little more sensitive to the choice of donor. The mono dithienothiophene and the dithienopyrrole polymers were found to exhibit electron mobilities as high as 1.3 × 10−2 and 1.2 × 10−3 cm2V−1s−1, respectively, in top-contact organic field-effect transistors. Power conversion efficiencies in the range 0.77–1.1% were obtained under simulated AM 1.5, 100 mW/cm2 irradiation for all-polymer solar cells using the dithienothiophene-based polymers as acceptors in a 1 : 1 ratio with a polythiophene derivative as a donor. The device performance varies with the conjugation length of oligo(dithienothiophene) in the polymer acceptors, and for the best-performing material it can be further optimized to give a power conversion efficiency of 1.5% by increasing the donor/acceptor weight ratio to 3 : 1.
Introducing Porphyrin Units by Random Copolymerization into NDI-Based Acceptor for All Polymer Solar Cells

Jinliang Liu,Mengzhen Li,Dong Chen,Bin Huang,Qiannan He,Shanshan Ding,Wenquan Xie,Feiyan Wu,Lie Chen,Yiwang Chen

DOI: https://doi.org/10.3389/fchem.2020.00310

IF: 5.5

2020-01-01

Frontiers in Chemistry

Abstract:Naphthalene diimide (NDI)-based polymer N2200 is a promising organic polymer acceptor for all-polymer solar cells (all-PSCs), but its inherent shortcomings like poor extinction coefficient and strong aggregation limit further performance optimization of all-PSCs. Here, a series of random copolymers, PNDI-Px, were designed and synthesized by introducing porphyrin unit into NDI-based polymer as acceptors for all-PSCs. These random copolymers show a higher absorption coefficient and raised the lowest unoccupied molecular orbital (LUMO) energy levels compared to N2200. The crystallinity can also be fine-tuned by regulation of the content of porphyrin unit. The random copolymers are matched with polymer donor PBDB-T for the application in all-polymer solar cells. The best power conversion efficiency (PCE) of these PNDI-Px-based devices is 5.93%, ascribed to the overall enhanced device parameters compared with the N2200-based device. These results indicate that introducing porphyrin unit into polymer is a useful way to fine-tune the photoelectric performance for efficient all-PSCs.
Dye-incorporated Polynaphthalenediimide Acceptor for Additive-free High-performance All-polymer Solar Cells.

Dong Chen,Jia Yao,Lie Chen,Jingping Yin,Ruizhi Lv,Bin Huang,Siqi Liu,Zhi-Guo Zhang,Chunhe Yang,Yiwang Chen,Yongfang Li

DOI: https://doi.org/10.1002/anie.201800035

2018-01-01

Abstract:All-polymer solar cells (all-PSCs) can offer unique advantages for applications in flexible devices, and naphthalene diimide (NDI)-based polymer acceptors are the widely used polymer acceptors. However, their power conversion efficiency (PCE) still lags behind that of state-of-the-art polymer solar cells, due to low light absorption, suboptimal energy levels and the strong aggregation of the NDI-based polymer acceptor. Herein, a rhodanine-based dye molecule was introduced into the NDI-based polymer acceptor by simple random copolymerization and showed an improved light absorption coefficient, an up-shifted lowest unoccupied molecular orbital level and reduced crystallization. Consequently, additive-free all-PSCs demonstrated a high PCE of 8.13%, which is one of the highest performance characteristics reported for all-PSCs to date. These results indicate that incorporating a dye into the n-type polymer gives insight into the precise design of high-performance polymer acceptors for all-PSCs.
Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64% Efficiency All Polymer Solar Cells

Min Deng,Xiaopeng Xu,Wuke Qiu,Yuwei Duan,Ruipeng Li,Liyang Yu,Qiang Peng

DOI: https://doi.org/10.1002/anie.202405243

2024-06-13

Angewandte Chemie International Edition

Abstract:All-polymer solar cells have experienced rapid development in recent years by the emergence of polymerized small molecular acceptors (PSMAs). However, the strong chain entanglements of polymer donors (PDs) and polymer acceptors (PAs) decrease the miscibility of the resulting polymer mixtures, making it challenging to optimize the blend morphology. Herein, we designed three PAs, namely PBTPICm-BDD, PBTPICγ-BDD and PBTPICF-BDD, by smartly using a BDD unit as the polymerized unit to copolymerize with different Y-typed non-fullerene small molecular acceptors (NF-SMAs), thus achieving a certain degree of distortion and giving the polymer system enough internal space to reduce the entanglements of the polymer chains. Such effects increase the chances of the PD being interspersed into the acceptor material, which improve the solubility between the PD and PA. The PBTPICγ-BDD and PBTPICF-BDD displayed better miscibility with PBQx-TCl, leading to a well optimized morphology. As a result, high power conversion efficiencies (PCEs) of 17.50% and 17.17% were achieved for PBQx-TCl:PBTPICγ-BDD and PBQx-TCl:PBTPICF-BDD devices, respectively. With the addition of PYF-T-o as the third component into PBQx-TCl:PBTPICγ-BDD blend to further extend the absorption spectral coverage and finely tune microstructures of the blend morphology, a remarkable PCE of 18.64% was realized finally.

chemistry, multidisciplinary
Dithienocoronene Diimide Based Conjugated Polymers As Electron Acceptors for All-Polymer Solar Cells

Weiyi Zhou,Zhi-Guo Zhang,Lanchao Ma,Yongfang Li,Xiaowei Zhan

DOI: https://doi.org/10.1016/j.solmat.2013.01.005

2013-01-01

Abstract:A series of n-type copolymers based on dithienocoronene diimide with different number of thiophene units have been designed and synthesized by Pd-catalyzed Stille coupling polymerization. The soluble polymers P1–P3 exhibit good thermal stability with decomposition temperatures of 340−390°C. The absorption spectra (400–700nm) red shift, and optical band gap (1.7–1.9eV) decreases with increasing thiophene number in the copolymers. The estimated LUMOs for these polymers (ca. −3.5eV) are relatively insensitive to thiophene number, while the HOMOs (−6.0 to −5.7eV) up shift with increasing thiophene number. Solution processed bulk heterojunction all-polymer solar cells are fabricated using polymers P1–P3 as acceptor and polythiophene derivative PT5TPA as donor. Power conversion efficiencies (upto 0.84%) increase with increasing thiophene number in the polymer acceptors.
Naphthalene diimide-based random terpolymer acceptors for constructing all-polymer solar cells with enhanced fill factors

Baitian He,Longfei Liu,Yan Liu,Guiting Chen,Manjun Xiao,Chuanbo Dai

DOI: https://doi.org/10.1039/d2ra03062d

IF: 4.036

2022-01-01

RSC Advances

Abstract:We developed two terpolymer acceptors based on N2200 through random copolymerization for all polymer solar cells with enhanced fill factors and photovoltaic performance.

chemistry, multidisciplinary
Non-fullerene organic solar cells based on diketopyrrolopyrrole polymers as electron donors and ITIC as an electron acceptor

Xudong Jiang,Yunhua Xu,Xiaohui Wang,Yang Wu,Guitao Feng,Cheng Li,Wei Ma,Weiwei Li

DOI: https://doi.org/10.1039/c7cp00494j

2017-03-15

Abstract:In this work, we provide systematic studies on the non-fullerene solar cells based on diketopyrrolopyrrole (DPP) polymers as electron donors and a well-known electron acceptor ITIC. ITIC has been widely reported in non-fullerene solar cells with high power conversion efficiencies (PCEs) above 10%, when it is combined with a wide band gap conjugated polymer, while its application in small band gap DPP polymers has never been reported. Herein, we select four DPP polymers containing different thienyl linkers, resulting in distinct absorption spectra, energy levels and crystalline properties. Non-fullerene solar cells based on DPP polymers as donors and ITIC as an acceptor show PCEs of 1.9-4.1% and energy loss of 0.55-0.82 eV. The PCEs are much lower than those of cells based on fullerene derivatives due to the poor miscibility between the DPP polymers and ITIC, as confirmed by the morphology and charge transport investigation. The results indicate that it is important to tune the miscibility between the donor and acceptor in order to realize optimized micro-phase separation, which can further enhance the performance of DPP polymer based non-fullerene solar cells.
Polymer acceptor based on naphthalene diimide and diethynylbenzo[1,2-b:4,5-b'] dithiophene units for efficient all-polymer solar cells

Ruihao Xie,Yiming Liang,Jianhua Jing,Jinfan Chen,Renlong Li,Kai Zhang

DOI: https://doi.org/10.1016/j.dyepig.2021.109246

IF: 5.122

2021-05-01

Dyes and Pigments

Abstract:Five polymer acceptors based on naphthalene diimide (NDI) and diethynylbenzo[1,2-b:4,5-b']dithiophene (DEBDT) alternating units were designed and synthesized. The resultant polymers have identical polymer backbones but different side chains on both NDI and DEBDT units. Their photoelectronic properties can be fine-tuned via systematic side chain engineering. In these polymers, the size of the alkyl side chains on NDI units have minimal impacts on light-harvesting properties and molecular energy levels, while introducing side chain groups into DEBDT units can significantly broad the absorption profile and tune the lowest unoccupied molecular orbital energy levels of polymers. All-polymer solar cells (all-PSCs) based on these polymer acceptors and PBDB-T as the electron-donating polymer were fabricated, where the power conversion efficiencies (PCEs) varied from 0.42% to 5.84%. All-PSCs based on PBDB-T:PNEOD-C8 exhibits the best device performance, which can be ascribed to the lowered energy loss, good light-harvesting capability, balanced charge carrier mobility and proper blend film morphology. These observations indicate that modifying the side chains on both donor and acceptor unit of polymer acceptors is an effective strategy for optimizing their optical and electrical properties, thus lead to high-performance all-PSCs.

engineering, chemical,chemistry, applied,materials science, textiles
Perylene and Naphthalene Diimide Polymers for All-Polymer Solar Cells: a Comparative Study of Chemical Copolymerization and Physical Blend

Shuixing Dai,Pei Cheng,Yuze Lin,Yifan Wang,Lanchao Ma,Qidan Ling,Xiaowei Zhan

DOI: https://doi.org/10.1039/c5py00665a

IF: 4.6

2015-01-01

Polymer Chemistry

Abstract:Five copolymers, having 4,4,9,9-tetrakis(4-hexylphenyl)-indaceno[1,2-b:5,6-b′]-dithiophene as a donor unit, and perylene diimide (PDI) and/or naphthalene diimide (NDI) as acceptor moieties, were synthesized, and used as electron acceptors in polymer solar cells.
High Performance All-Polymer Solar Cells by Synergistic Effects of Fine-Tuned Crystallinity and Solvent Annealing.

Zhaojun Li,Xiaofeng Xu,Wei Zhang,Xiangyi Meng,Wei Ma,Arkady Yartsev,Olle Inganas,Mats. R. Andersson,Rene A. J. Janssen,Ergang Wang

DOI: https://doi.org/10.1021/jacs.6b04822

IF: 15

2016-01-01

Journal of the American Chemical Society

Abstract:Growing interests have been devoted to the design of polymer acceptors as potential replacement for fullerene derivatives for high-performance all polymer solar cells (all-PSCs). One key factor that is limiting the efficiency of all-PSCs is the low fill factor (FF) (normally <0.65), which is strongly correlated with the mobility and film morphology of polymer:polymer blends. In this work, we find a facile method to modulate the crystallinity of the well-known naphthalene diimide (NDI) based polymer N2200, by replacing a certain amount of bithiophene (2T) units in the N2200 backbone by single thiophene (T) units and synthesizing a series of random polymers PNDI-Tx, where x is the percentage of the single T. The acceptor PNDI-T10 is properly miscible with the low band gap donor polymer PTB7-Th, and the nanostructured blend promotes efficient exciton dissociation and charge transport. Solvent annealing (SA) enables higher hole and electron mobilities, and further suppresses the bimolecular recombination. As expected, the PTB7-Th:PNDI-T10 solar cells attain a high PCE of 7.6%, which is a 2-fold increase compared to that of PTB7-Th:N2200 solar cells. The FF of 0.71 reaches the highest value among all-PSCs to date. Our work demonstrates a rational design for fine-tuned crystallinity of polymer acceptors, and reveals the high potential of all-PSCs through structure and morphology engineering of semicrystalline polymer:polymer blends.
Novel High-Efficiency Polymer Acceptors Via Random Ternary Copolymerization Engineering Enables All-Polymer Solar Cells with Excellent Performance and Stability.

Dong Chen,Siqi Liu,Jiyeon Oh,Bin Huang,Ruizhi Lv,Jiabin Liu,Changduk Yang,Lie Chen

DOI: https://doi.org/10.1021/acsami.1c03739

IF: 9.5

2021-01-01

ACS Applied Materials & Interfaces

Abstract:Continuous breakthroughs have been achieved in improving the efficiency of all-polymer solar cells (all-PSCs) using diimide-based polymer acceptors, and their easy-to-synthesize, low-cost, and high stability attributes make them potential candidates for use in commercial all-PSCs. However, their low light absorption coefficient, strong aggregation, and poor adaptability with high-efficient polymer donors still limit further improvements in the device performance. Here, we combine the advantages of fluorinated bithiophene and rhodanine dye molecules to create low-cost diimide-based polymer acceptors, PNDI-2FT-TR10 and PNDI-2FT-TR20, by random copolymerization for achieving highly efficient and stable all-PSCs. The synergistic effects of fluorine atoms and rhodanine dye molecules not only significantly improve the absorption coefficient but also enable enhanced miscibility and stability of the blend film. When blended with a PM6 donor, the PNDI-2FT-TR10-based device exhibits a notable power conversion efficiency (PCE) of 10.71% with a short-circuit current (JSC) of 17.32 mA cm-2. Note that both the PCE and JSC show outstanding values for diimide-based all-PSCs, and this is the first report on blending diimide-based polymer acceptors with the PM6 donor to achieve high-performance all-PSCs. Moreover, the favorable morphology of the active layer enables the device to have good thickness tolerance and thermal stability. The results demonstrate that the absorption coefficients, blend morphology, and photovoltaic properties of all-PSCs could be rationally optimized by a random copolymer.
Rational Design of Perylenediimide-Based Polymer Acceptor for Efficient All-Polymer Solar Cells

Wentao Xiong,Xiangyi Meng,Tao Liu,Yunhao Cai,Xiaonan Xue,Zongbo Li,Xiaobo Sun,Lijun Huo,Wei Ma,Yanming Sun

DOI: https://doi.org/10.1016/j.orgel.2017.08.005

IF: 3.868

2017-01-01

Organic Electronics

Abstract:Perylenediimide (PDI)-based small molecules have significantly contributed to the development of nonfullerene acceptors, whereas the development of PDI-based polymer acceptors is relatively lagging behind. In this study, we designed and synthesized two PDI-based n-type polymers named as PF-PDI and PBDT- PDI, in which PDI was used as electron-deficient unit and fluorene (F) or benzodithiophene (BDT) were used as electronrich components. The density functional theory (DFT) calculations and grazing incidence wide-angle X-ray scattering (GIWAXS) results indicate that the PF-PDI shows larger steric hindrance and relatively weaker lamellar packing than that of PBDT-PDI. Comparing with PBDT-PDI, PFPDI shows red-shift absorption and lower-lying HOMO level, which agrees well with the DFT results. A well-known wide bandgap polymer donor, PDBT-T1 was employed to fabricate polymer solar cells (PSCs) with the two acceptors. The all polymer solar cells (all-PSCs) based on PDBT-T1: PF-PDI showed a high power conversion efficiency (PCE) of 4.47%, which is approximately 2-fold larger than that of devices with PDBT-T1: PBDT-PDI (PCE = 2.70%). (C) 2017 Elsevier B.V. All rights reserved.
8.0% Efficient All-Polymer Solar Cells Based on Novel Starburst Polymer Acceptors

Kang Li,Ruihao Xie,Wenkai Zhong,Kaiwen Lin,Lei Ying,Fei Huang,Yong Cao

DOI: https://doi.org/10.1007/s11426-017-9197-0

2018-01-01

Science China Chemistry

Abstract:The polymer N2200, with its π-conjugated backbone composed of alternating naphthalene diimide(NDI) and bithiophene(DT)units, has been widely used as an acceptor for all-polymer solar cells(all-PSCs) owing to its high electron mobility and suitable ionization potential and electron affinity. Here, we developed two naphthalene diimide derivatives by modifying the molecular geometry of N2200 through the incorporation of a truxene unit as the core and NDI-DTas the branches. These starburst polymers exhibited absorption spectra and molecular orbital energy levels that were comparable to N2200. These copolymers were paired with the wide-bandgap polymer donor PTz BI-O to fabricate all-polymer solar cells(all-PSCs), which displayed impressive power conversion efficiencies up to 8.00%. The improved photovoltaic performances of all-PSCs based on these newly developed starburst acceptors can be ascribed to the combination of increased charge carrier mobilities, reduced bimolecular recombination, and formation of more favorable film morphology. These findings demonstrate that the construction of starburst polymer acceptors is a feasible strategy for the fabrication of high-performance all-PSCs.
Novel Perylene Diimide Based Polymeric Electron-Acceptors Containing Ethynyl As the Π-Bridge for All-Polymer Solar Cells

Huan Chang,Zhiming Chen,Xiye Yang,Qingwu Yin,Jie Zhang,Lei Ying,Xiao-Fang Jiang,Baomin Xu,Fei Huang,Yong Cao

DOI: https://doi.org/10.1016/j.orgel.2017.03.022

IF: 3.868

2017-01-01

Organic Electronics

Abstract:We designed and synthesised two n-type donor-acceptor copolymers based on perylenediimide (PDI). These copolymers contained an ethynyl moiety as the pi-bridge between PDI and the electron-donating unit of either benzodithiophene (BDT) or fluorine (F), with the corresponding polymers denoted as PPDI-BDT and PPDI-F, respectively. The molecular geometry and the optical and electrochemical properties of the polymers were affected by the electron-donating unit. Both copolymers exhibited relatively broad light-absorption profiles and deep lowest unoccupied molecular orbital energy levels of about -3.8 eV. All-polymer solar cells (all-PSCs) were fabricated using these copolymers as the electron-accepting material and a medium-bandgap conjugated polymer, PBDB-T, as the electron-donating material. The resulting all-PSC based on PPDI-F exhibited a power conversion efficiency of 5.09%, which is significantly higher than that of the device fabricated using PPDI-BDT (2.73%). This improvement was attributed to the higher open-circuit voltage, greater charge carrier mobility and more effective charge transfer of the PBDB-T:PPDI-F blend film. These results suggest that the developed n-type PDI-based copolymers are promising candidates as electron-accepting materials for the construction of high-performance all polymer solar cells. (C) 2017 Elsevier B.V. All rights reserved.
Comparing the Device Physics, Dynamics and Morphology of Polymer Solar Cells Employing Conventional PCBM and Non-Fullerene Polymer Acceptor N2200

Jianyu Yuan,Wenping Guo,Yuxin Xia,Michael J. Ford,Feng Jin,Dongyang Liu,Haibin Zhao,Olle Inganas,Guillermo C. Bazan,Wanli Ma

DOI: https://doi.org/10.1016/j.nanoen.2017.03.050

IF: 17.6

2017-01-01

Nano Energy

Abstract:Current all polymer solar cells still suffer from low fill factors (FF) and short-circuit current density (Jsc) compared with the conventional polymer/fullerene system. Herein in this work, devices using PTP8 as the electron donor and [70]PCBM as well as widely used polymer N2200 as the electron acceptor were systematically studied and compared. The major loss mechanisms in the all polymer solar cells were investigated to understand their relatively lower performance than the PTP8/fullerene system. By performing in-depth analysis on ultrafast transient transmission spectroscopy results, we estimated that in PTP8/N2200 device nearly half of the charges recombine geminately, which is confirmed as the major factor hindering the device performance of all polymer solar cells compared with polymer/fullerene system. Through thorough morphology analysis, the low charge generation efficiency is attributed to the reduced crystallinity of N2200 in the blend film and the unfavorable face-to-edge orientation at the donor/acceptor heterojunction. Coupling these results with knowledge from efficient polymer/fullerene systems, the future design of new polymers can devote to increase the attraction between the π face of donor and acceptor, leading to enhanced face-to-face orientation at the heterojunction, while maintaining a high π-π stacking order for each polymer.
Comparison of three n-type copolymers based on benzodithiophene and naphthalene diimide /perylene diimide/fused perylene diimides for all-polymer solar cells application.

Jing Yang,Yuli Yin,Fan Chen,Yong Zhang,Bo Xiao,Liancheng Zhao,Erjun Zhou

DOI: https://doi.org/10.1021/acsami.8b06306

IF: 9.5

2018-01-01

ACS Applied Materials & Interfaces

Abstract:All-polymer solar cells have attracted great attention due to their tunable energy levels and absorption spectra of both donor and acceptor. Comparing to the numerous polymer donors, the development of polymer acceptors was relatively slow. Rylene diimide based polymers are regarded as the most promising n-type polymers, which were widely investigated in the past decade and some novel rylene diimide structures are constantly designed. In this work, three n-type polymers with donor-acceptor (D-A) alternative backbone structure, named as PNDI-BDT, PPDI-BDT and PFPDI-BDT, were designed and synthesized. In these polymers, naphthalene diimide (NDI), perylene diimide (PDI) and recently developed fused perylene diimide (FPDI) were used as electron-deficient unit respectively, and benzodithiophene (BDT) with thiophenes as conjugated side chains was utilized as electron-rich unit. The optical properties, electron energy levels, charge transport properties, photovoltaic performance, charge recombination loss and surface morphology were systematically investigated. After optimizing the device fabrication conditions, PNDI-BDT, PPDI-BDT and PFPDI-BDT based all-polymer solar cells (all-PSCs) realized the power conversion efficiencies (PCE) of 0.88%, 3.74% and 5.65%, respectively. The results indicated that FPDI is an effective building block to construct n-type polymers and PFPDI-BDT is a promising polymer acceptor for application in all-PSCs.
Perylene and Naphthalene Diimide Copolymers for All‐polymer Solar Cells: Effect of Perylene/naphthalene Ratio

Shuixing Dai,Shuai Huang,Haifeng Yu,Qidan Ling,Xiaowei Zhan

DOI: https://doi.org/10.1002/pola.28392

2017-01-01

Abstract:ABSTRACTWe report the synthesis of a series of copolymers, having 2,2′‐bithiophene as electron‐donating moiety, and perylene diimide (PDI) and/or naphthalene diimide (NDI) as electron‐accepting moiety, and employed as non‐fullerene acceptors in polymer solar cells (PSCs). All the copolymers show wide absorption varying from 300 to 850 nm in the visible and NIR spectrum. When changing the PDI/NDI ratio in the polymer backbone, The LUMO energy levels vary in the range of −3.90 to −3.80 eV and the HOMO energy levels vary in the range of −6.10 to −5.85 eV. Among PSCs based on PTB7‐Th donor and these polymer acceptors, the devices based on PTB7‐Th/NDI100 yield the best power conversion efficiency (PCE) of 4.67%, while the PTB7‐Th/PDI100‐based devices yield a PCE of 1.03%. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017, 55, 682–689
Bandgap Engineering of Dual Acceptor-Containing Naphthalene Diimide Polymers for All-Polymer Solar Cells

Dandan Tu,Xuan Liu,Jing Zhang,Qing Yang,Shuwen Yu,Xin Guo,Can Li

DOI: https://doi.org/10.1021/acssuschemeng.8b05021

IF: 8.4

2018-01-01

ACS Sustainable Chemistry & Engineering

Abstract:Naphthalene diimide (NDI)-based polymers, as nonfullerene acceptors for all-polymer solar cells (all-PSCs), are usually investigated by manipulating electron-donating units, which have a narrow bandgap showing absorption spectra mostly overlapping with high-performance donor polymers like PTB7-Th. In order to gain complementary absorptions between NDI-based polymers and PTB7-Th, we report three NDI-based polymers (P1–P3) designed by a dual-acceptor strategy and systematically study their effect on the bandgap, molecular configuration, and charge transport property. The absorption bands of these polymers range from 300 to 800 nm; in particular, P1 with a maximum absorption at 530 nm exhibits a good complementary absorption with the PTB7-Th. The device based on the PTB7-Th:P1 blend provides higher Jsc and efficiency than those based on other two polymers. The result suggests that the dual-acceptor strategy is effective to design acceptor polymers with adjustable absorption and molecular configuration for th...
High-efficiency all-polymer solar cells based on a pair of crystalline low-bandgap polymers.

Cheng Mu,Peng Liu,Wei Ma,Kui Jiang,Jingbo Zhao,Kai Zhang,Zhihua Chen,Zhanhua Wei,Ya Yi,Jiannong Wang,Shihe Yang,Fei Huang,Antonio Facchetti,Harald Ade,He Yan

DOI: https://doi.org/10.1002/adma.201402473

IF: 29.4

2014-01-01

Advanced Materials

Abstract:All-polymer solar cells based on a pair of crystalline low-bandgap polymers (NT and N2200) are demonstrated to achieve a high short-circuit current density of 11.5 mA cm-2 and a power conversion efficiency of up to 5.0% under the standard AM1.5G spectrum with one sun intensity. The high performance of these NT:N2200-based cells can be attributed to the low optical bandgaps of the polymers and the reasonably high and balanced electron and hole mobilities of the NT:N2200 blends due to the crystalline nature of the two polymers.

All Polymer Solar Cells with Diketopyrrolopyrrole-Polymers As Electron Donor and A Naphthalenediimide-Polymer As Electron Acceptor

Naphthalenediimide-based N-Type Polymer Acceptors with Pendant Twisted Perylenediimide Units for All-Polymer Solar Cells

Copolymers of perylene diimide with dithienothiophene and dithienopyrrole as electron-transport materials for all-polymer solar cells and field-effect transistors

Introducing Porphyrin Units by Random Copolymerization into NDI-Based Acceptor for All Polymer Solar Cells

Dye-incorporated Polynaphthalenediimide Acceptor for Additive-free High-performance All-polymer Solar Cells.

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64% Efficiency All Polymer Solar Cells

Dithienocoronene Diimide Based Conjugated Polymers As Electron Acceptors for All-Polymer Solar Cells

Naphthalene diimide-based random terpolymer acceptors for constructing all-polymer solar cells with enhanced fill factors

Non-fullerene organic solar cells based on diketopyrrolopyrrole polymers as electron donors and ITIC as an electron acceptor

Polymer acceptor based on naphthalene diimide and diethynylbenzo[1,2-b:4,5-b'] dithiophene units for efficient all-polymer solar cells

Perylene and Naphthalene Diimide Polymers for All-Polymer Solar Cells: a Comparative Study of Chemical Copolymerization and Physical Blend

High Performance All-Polymer Solar Cells by Synergistic Effects of Fine-Tuned Crystallinity and Solvent Annealing.

Novel High-Efficiency Polymer Acceptors Via Random Ternary Copolymerization Engineering Enables All-Polymer Solar Cells with Excellent Performance and Stability.

Rational Design of Perylenediimide-Based Polymer Acceptor for Efficient All-Polymer Solar Cells

8.0% Efficient All-Polymer Solar Cells Based on Novel Starburst Polymer Acceptors

Novel Perylene Diimide Based Polymeric Electron-Acceptors Containing Ethynyl As the Π-Bridge for All-Polymer Solar Cells

Comparing the Device Physics, Dynamics and Morphology of Polymer Solar Cells Employing Conventional PCBM and Non-Fullerene Polymer Acceptor N2200

Comparison of three n-type copolymers based on benzodithiophene and naphthalene diimide /perylene diimide/fused perylene diimides for all-polymer solar cells application.

Perylene and Naphthalene Diimide Copolymers for All‐polymer Solar Cells: Effect of Perylene/naphthalene Ratio

Bandgap Engineering of Dual Acceptor-Containing Naphthalene Diimide Polymers for All-Polymer Solar Cells

High-efficiency all-polymer solar cells based on a pair of crystalline low-bandgap polymers.