Abstract:The development of readily accessible polymer acceptors is imperative to preserve the guiding principles of all-polymer solar cells as a low-cost and sustainable technology for alternative energy production. In this study, we report a computationally guided design and facile synthesis of new acceptor polymers comprising the alternating copolymer, PNIT, and the corresponding random copolymer, r-PNIT, which incorporate structurally simple naphthalene diimide (NDI) and isoindigo (IID) units. PNIT was prepared via direct arylation polymerization (DArP), which proceeds via C–H activation and avoids the use of toxic reagents and extended synthetic pathways for the monomer synthesis. PNIT has broad optical absorption in the 300–850 nm range and an enhanced absorption coefficient (47 × 103 cm–1) compared to r-PNIT (300–850 nm; 40 × 103 cm–1). When incorporated in all-polymer solar cells (APSCs) using PBDB-T as the donor polymer, PBDB-T:PNIT provides greater than two times the average (maximum) power conversion efficiency (PCE) of 5.18 ± 0.08 (5.32)% compared to that of PBDB-T:r-PNIT, 2.38 ± 0.16 (2.57)%, due to increased Jsc (10.36 vs 5.45 mA cm–2) and fill factor (FF) (0.58 vs 0.50) metrics. The PBDB-T:PNIT PCE is among the highest reported for an IID-based APSC and demonstrates the viability of DArP for the synthesis of new APSC acceptor polymers. Detailed morphological and microstructural investigations using atomic force microscopy (AFM) and grazing-incidence wide-angle X-ray scattering (GIWAXS), respectively, reveal enhanced texturing for PNIT, which enhances charge transport properties as supported by space-charge-limited current (SCLC) mobility measurements.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.chemmater.2c00065.Experimental procedures; synthesis and characterization of monomers and polymers; monomer and polymer NMR; GPC traces; TGA and DSC thermograms; contact angle measurements; CV and thin-film absorption measurements; DFT and TD-DFT calculations; device fabrication and testing parameters for APSCs and SCLC charge mobility measurements; and thin-film fabrication and measurement procedures for GIWAXS and AFM (PDF)This article has not yet been cited by other publications.

Dye-incorporated Polynaphthalenediimide Acceptor for Additive-free High-performance All-polymer Solar Cells.

Polymer acceptor based on naphthalene diimide and diethynylbenzo[1,2-b:4,5-b'] dithiophene units for efficient all-polymer solar cells

Novel High-Efficiency Polymer Acceptors Via Random Ternary Copolymerization Engineering Enables All-Polymer Solar Cells with Excellent Performance and Stability.

Introducing Porphyrin Units by Random Copolymerization into NDI-Based Acceptor for All Polymer Solar Cells

Improved Performance of All‐Polymer Solar Cells Enabled by Naphthodiperylenetetraimide‐Based Polymer Acceptor

Naphthalenediimide-based N-Type Polymer Acceptors with Pendant Twisted Perylenediimide Units for All-Polymer Solar Cells

Thiophene-Fused Perylenediimide-Based Polymer Acceptors for High-Performance All-Polymer Solar Cells

High-performance All-Polymer Solar Cells Based on Fluorinated Naphthalene Diimide Acceptor Polymers with Fine-Tuned Crystallinity and Enhanced Dielectric Constants

N‐type Conjugated Polymer Based on Dicyanodistyrylbenzene and Naphthalene Diimide Units for All‐Polymer Solar Cells

Rational Design of Perylenediimide-Based Polymer Acceptor for Efficient All-Polymer Solar Cells

All-Polymer Solar Cells Incorporating Readily Accessible Naphthalene Diimide and Isoindigo Acceptor Polymers for Improved Light Harvesting

High-Performance All-Polymer Solar Cells Achieved by Fused Perylenediimide-Based Conjugated Polymer Acceptors.

Bandgap Engineering of Dual Acceptor-Containing Naphthalene Diimide Polymers for All-Polymer Solar Cells

High-performance All-Polymer Nonfullerene Solar Cells by Employing an Efficient Polymer-Small Molecule Acceptor Alloy Strategy

High Performance All-Polymer Solar Cells by Synergistic Effects of Fine-Tuned Crystallinity and Solvent Annealing.

Synergistic Effects of Copolymerization and Fluorination on Acceptor Polymers for Efficient and Stable All-Polymer Solar Cells

Novel polymer acceptors achieving 10.18% efficiency for all-polymer solar cells

10.13% Efficiency All‐Polymer Solar Cells Enabled by Improving the Optical Absorption of Polymer Acceptors

Regulation Of The Miscibility Of The Active Layer By Random Terpolymer Acceptors To Realize High-Performance All-Polymer Solar Cells

8.0% Efficient All-Polymer Solar Cells Based on Novel Starburst Polymer Acceptors

Comparison of three n-type copolymers based on benzodithiophene and naphthalene diimide /perylene diimide/fused perylene diimides for all-polymer solar cells application.