Abstract:In this study, equal channel angular pressing (ECAP) was applied to a hot-extruded Mg–5.00Zn–0.92Y–0.16Zr (wt.%) alloy to produce an ultrafine-grained a-Mg structure of 0.6μm with uniformly distributed fine quasicrystal Mg3YZn6 particles. The basal planes in the as-ECAPed alloy were inclined approximately 45° to the ECAP direction (EPD); thus, a high Schmid factor of 0.36 for (0001)〈112¯0〉 basal slip along EPD was obtained. Then, the superplastic behavior at low temperatures of 150–250°C and initial strain rates of 1.67×10−3s−1–1.67×10−1s−1 of the as-ECAPed alloy was investigated and compared with that of the as-extruded alloy. The microstructural development, texture evolution and cracking behavior during tensile tests were systemically investigated by electron backscattered diffraction (EBSD) analysis. During the tensile test along the EPD, the basal planes in the as-ECAPed alloy specimen were tilted approximately 15° away from the original position; thus, the basal planes were still in a position favorable for the basal slip along the EPD. As a result, a maximum elongation of 865% was obtained at 200°C and a strain rate of 1.67×10−3s−1, as a result of this favored basal texture and the excellent thermal stability of the ultrafine-grained structure. This optimum superplastic temperature of 200°C is much lower than that obtained for other Mg–Zn–Y–(Zr) alloys. In contrast, for the as-extruded alloy specimen, superplastic behavior did not occur until the critical condition of 250°C and a strain rate of 1.67×10−3s−1. Below this temperature and strain rate, the strong extrusion basal texture was maintained, and the cracks in the hot-worked coarse region (or un-DRXed region) were observed nucleating mainly associated with the formation of a 38° {101¯1}–{101¯2} double twin. At this temperature and strain rate, the hot-worked coarse regions were significantly refined by the dynamic recovery and the following recrystallization process. In the case, the formation of a double twin was prevented and the facture was delayed.

Microstructural Evolution of a Fine-Grained Mg-Y-Nd Alloy During Superplastic Deformation

Superplastic Behavior and Microstructure Evolution of a Fine-Grained Mg–Y–Nd Alloy Processed by Submerged Friction Stir Processing

High‐Strain‐Rate Superplasticity in Mg–Y–Nd Alloy Prepared by Submerged Friction Stir Processing

Superplastic Behavior and Microstructure Evolution of a Fine-Grained Mg-Nd-Zn-Zr Alloy Processed by Hot Extrusion

Microstructure and Mechanical Properties of Submerged Friction Stir Processing Mg-Y-Nd Alloy

Microstructural Evolution and Enhanced Superplasticity in Friction Stir Processed Mg–Zn–Y–Zr Alloy

Excellent High‐Strain‐Rate Superplasticity of Fine‐Grained ZK60 Magnesium Alloy Produced by Submerged Friction Stir Processing

Microstructure evolution during superplastic deformation process and its impact on superplastic behavior of a Mg-Gd-Y-Zn-Zr alloy

Microstructure and texture evolution during high-strain-rate superplastic deformation of coarse-grained Mg-Gd-Y-Zr rolled sheet

High Strain Rate Superplasticity in a Micro-grained Al{Mg{Sc Alloy with Predominant High Angle Grain Boundaries

Microstructure evolution and mechanical properties of Mg–Nd–Y alloy in different friction stir processing conditions

Superplastic Behaviors of a Mg–Zn–Y–Zr Alloy Processed by Extrusion and Equal Channel Angular Extrusion

The Microstructural Evolution and Superplastic Behavior at Low Temperatures of Mg–5.00Zn–0.92Y–0.16Zr (wt.%) Alloys after Hot Extrusion and ECAP Process

Superplastic Behavior and Microstructural Evolution in a Commercial Mg-3Al-1Zn Magnesium Alloy.

Superplastic Behavior of an Extruded Mg-Zn-Y-Zr Alloy

Superplasticity of Mg-5.8Zn-1Y-Zr Alloy Sheet Fabricated by Combination of Extrusion and Hot-Rolling Processes

High Strain Rate Quasi-Superplasticity Behavior in an Ultralight Mg-9.55Li-2.92Al-0.027Y-0.026Mn Alloy Fabricated by Multidirectional Forging and Asymmetrical Rolling

Superplastic Behavior and Microstructure Evolution of A New Al-Mg-Sc-Zr Alloy Subjected to A Simple Thermomechanical Processing

Influence of Processing Speed on Microstructures and Mechanical Properties of Friction Stir Processed Mg–Y–Nd–Zr Casting Alloy

Achieving Superior Superplasticity in a Mg–6Al–Zn Plate via Multi-pass Submerged Friction Stir Processing

Superplastic Deformation Behavior of Fine-Grained AZ80 Magnesium Alloy Prepared by Friction Stir Processing