Abstract:Wear‐resistant metal matrix composites (MMC) are common engineering materials which have been used for many industrial hardfacing applications. This work provides the detailed characterization of a laser‐clad MMC consisting of hard tungsten carbide particles embedded in a comparatively soft nickel alloy matrix, which has been intended to be used for potential rolling mill applications. Special focus of the investigations was placed on the relationship between the microstructure of the as‐deposited reinforcing particles and their hardness. Therefore, thermally induced dissolution of carbides caused by laser metal deposition (LMD) processing was studied. The methods of investigation include X‐ray diffraction (XRD), X‐ray micro‐computed tomography (μCT), transmission electron microscopy (TEM) with selected area electron diffraction (SAED), as well as scanning electron microscopy (SEM) combined with energy‐dispersive X‐ray spectroscopy (EDS), electron backscatter diffraction (EBSD) and nanoindentation. The as‐received powder blend mainly consisted of fused spherical particles of ditungsten carbides (W2C, W2C1–x) and monotungsten carbides (WC, WC1–x). Dissolution of large particles at the matrix/particle interfaces and fragmentation or even complete dissolution of small particles due to the high process temperature of LMD was observed. Primary W2C/W2C1–x phases were partially dissoluted and layers of secondary WC/NixWyC phases formed at the matrix/particle interfaces. As these surface layers were less hard than the as‐received particles, the local hardness gradually decreased from the inner region of the particles across the surface layer towards the matrix, which is supposed to improve bonding of particles inside the matrix. The hardness was dependent on the grain size and on the crystal structure of the carbides. Even when the crystal structures were identical, particles consisting of fine grains had considerably higher hardness than particles consisting of coarse grains. This article is protected by copyright. All rights reserved.

Crack initiation and propagation behavior of WC particles reinforced Fe-based metal matrix composite produced by laser melting deposition

Microstructure and mechanical properties of WC reinforced 18Ni300 composites produced by selective laser melting

Effect of WC addition on TiC reinforced Fe matrix composites produced by laser deposition

Effect of WC–Co addition on tribological and cracking behavior of laser cladded Fe-based amorphous/crystalline composite coatings

Influence of Processing Technique on Practical Large Area Metal-Matrix Composite Coating Produced by Laser Cladding

Microstructure and fracture behavior of 90W-7Ni-3Fe alloy fabricated by laser directed energy deposition

Microstructure characterization of nickel matrix composite reinforced with tungsten carbide particles and produced by laser cladding

Thermal behavior and microstructure evolution mechanism of W-20%Fe alloy fabricated by laser metal deposition

Cracking in Laser Additively Manufactured W: Initiation Mechanism and a Suppression Approach by Alloying

Cracking Mechanisms in Additively Manufactured Pure Tungsten from Printing Single Tracks, Thin Walls and Cubes

MORPHOLOGIC CHARACTERISTICS OF IN SITU SYNTHESIZED CARBIDE PARTICLES IN LASER CLADDED Fe-BASED COMPOSITE COATINGS

Laser ablation behavior and mechanism of Cf/C–SiC composites under different laser energy densities

Microstructures and Properties of Ceramic Particle-Reinforced Metal Matrix Composite Layers Produced by Laser Cladding

Characterization of W–Cr Metal Matrix Composite Coatings Reinforced with WC Particles Produced on Low-Carbon Steel Using Laser Processing of Precoat

Macro–micro residual stress prediction and hot crack formation mechanism during laser melt injection processing of ZrO2 particles into Ti6Al4V substrate

Grain structure and cracks behaviors of tungsten with different geometrical shapes and support structure prepared by laser powder bed fusion

Densification, microstructural evolutions of 90W-7Ni-3Fe tungsten heavy alloys during laser melting deposition process

Mesoscopic simulation of surface morphology and thermodynamic mechanism during laser powder-bed fusing Ni-based composite: Underlying role of WC weight fraction

Influence of Mo micro-particles on crack formation, microstructure, and mechanical behaviour of laser powder bed fusion fabricated CuZrAl bulk metallic glass composites

Novel WC-reinforced iron-based composites with excellent mechanical properties synthesized by laser additive manufacturing: Underlying role of reinforcement weight fraction

Additive manufacturing of W–Fe composites using laser metal deposition: Microstructure, phase transformation, and mechanical properties