Abstract:(1) Background: the applications of ceramic materials in a friction pair and a moving pair are limited, just because of their poor toughness and unsatisfactory tribological characteristics. In view of this, Mo as a soft metal layer was added into a Si3N4 matrix to improve its toughness and tribological characteristics. (2) Methods: The microstructure and metal/ceramic transition layer were examined using X-ray diffraction, scanning electron microscope, electron dispersive X-ray spectroscopy, and Vickers hardness. Bending strength and fracture toughness were also measured. Tribological characteristics were obtained on the pin-on-disc wear tester. (3) Results: It can be found that the multilayer structure could improve the fracture toughness of laminated composite compared with single-phase Si3N4, but the bending strength was significantly reduced. Through microstructure observation, the transition layer of Si3N4/Mo-laminated composite was revealed as follows: Si3N4→MoSi2→Mo5Si3→Mo3Si→Mo. Moreover, the addition of the Mo interface to silicon nitride ceramic could not significantly improve the tribological properties of Si3N4 ceramic against titanium alloy in seawater, and the friction coefficients and wear rates of the sliding pairs increased with the increase in load. (4) Conclusions: The process failed to simultaneously improve the comprehensive mechanical properties and tribological performance of Si3N4 ceramic by adding Mo as the soft interfacial layer. However, the utilization of metal interfacial layers to enhance the toughness of ceramics was further recognized and has potential significance for the optimization of ceramic formulation.

Control of Residual Stresses in 2Si-B-3c-n and Nb Joints by the Ag-Cu-Ti+Mo Composite Interlayer

Relieving Residual Stress in Brazed Joint Between SiC and Nb Using a 3D-Sio 2 -Fiber Ceramic Interlayer

Joint Microstructure and Performance of Brazing Si3N4‐MoSi2 Composites to Nb with AgCuTi and AgCuTi+MoSi2p Active Fillers

Microstructure and Mechanical Properties of the SiC/Nb Joint Brazed Using AgCuTi + B4C Composite Filler Metal

Microstructure Evolution and Mechanical Properties of SiC and Nb Joint Brazed with AgCuTi/(Sr0.2Ba0.8)TiO3-Cu/AgCuTi Composite Fillers

Brazing of C/C composites and 304 stainless steels via Ni/Mo composite interlayer

Microstructural control and reinforcement mechanism of the Mo and B inserts in the SiCf/SiC composites/Ni-based superalloy joint

Interfacial Microstructure and Mechanical Properties of the Vacuum Brazed C/SiC Composite and Nb Joints

Understanding the Microstructure Evolution Mechanism and the Microstructure-Strength Correlations of Ti3SiC2/Ti2AlNb Joint Brazed with AgCu Interlayer

Microstructure and mechanical properties of Si3N4 ceramic and (TiB + Y2O3)/Ti matrix composite joints brazed with AgCu/Cu foam/AgCu multilayered filler

Microstructure and mechanical properties of the joint between Si3N4 and Mo brazed by near‐eutectic Ag‐Cu‐In‐Ti filler alloy

Effect of Mo addition on interfacial microstructure and mechanical property of SiC joint brazed by an Ni–Si filler

Vacuum brazing SiC to Mo using Nb0.74CoCrFeNi2 eutectic high-entropy alloy filler

Design of Multi-Layered Architecture in Dissimilar Ceramic/metal Joints with Reinforcements Clustering Away from Both Substrates

Vacuum Brazing Nb and Bn-Sio2 Ceramic Using A Composite Interlayer with Network Reinforcement Architecture

A Study of the SiCf/SiC Composite/ni-Based Superalloy Dissimilar Joint Brazed with a Composite Filler

Interfacial Strengthening Mechanism of C/C/Nb0.74CoCrFeNi2/Nb Brazed Joints: Stress-relieving Effects of the FCC Phase

Effect of 3D-Sio2-fiber Interlayer on SiC and Nb Vacuum Brazing

Microstructural evolution and mechanical property of a SiCf/SiC composite/Ni-based superalloy joint brazed with an Au-Cu-Ti filler

Joining Si3N4 ceramic to Invar using Mo mesh and Cu foil interlayer

Microstructure, Mechanical and Tribological Properties of Si<sub>3</sub>N<sub>4</sub>/Mo-Laminated Composites