Abstract:Although <math>{101¯2}</math> twinning behavior has been extensively studied, it has rarely been investigated under biaxial tension. In the present research, the mechanical response and <math>{101¯2}</math> twinning behavior of a Mg AZ31 sheet under biaxial tension with various stress ratios (<math>σND:σTD</math>) along the normal direction (ND) and transverse direction (TD) were systematically studied. The results indicate that the yield stress along the ND is nearly independent of <math>σND:σTD</math>. Schmid law applied to <math>{101¯2}</math> twinning under biaxial tension yields better efficiency than that for uniaxial tension, and a higher efficiency is observed with a larger stress ratio along the TD; the fraction of experimentally observed twin variants with Schmid factors (SFs) of ranks 1 and 2 is approximately 45% for uniaxial tension, whereas it is approximately 68% for <math>σND:σTD=2:1</math> and approximately 88% for <math>σND:σTD=1:2</math>. This result contradicts with the previously reported result that Schmid law is more efficient for uniaxial stress states than under multiaxial stress conditions. It is found that biaxial tension will increase the difference in SF for the six twin variants and make Schmid law more efficient. Twin variant selection and volume fraction are highly dependent on <math>σND:σTD</math>. For uniaxial tension, the activities for the six variants are similar, and the (0002) poles of the twins are distributed evenly on a circle approximately 80°–90° away from the ND. In contrast, the variants <math>(01¯12)[011¯1]</math> and <math>(011¯2)[01¯11]</math> are more favorable under biaxial tension, and more (0002) poles of the twins concentrate around the rolling direction with a higher ratio of <math>σTD</math>. At a similar strain level, the twin fraction under biaxial tension is often different from that under uniaxial tension, and this difference varies with <math>σND:σTD</math>. This mechanism is associated with a stress-ratio-mediated detwinning behavior under biaxial tension. The findings in the present study provide a new and significant understanding of the twinning behavior of Mg alloys.

Experimental and Numerical Investigation of Anisotropic and Twinning Behavior in Mg Alloy under Uniaxial Tension

On the Modeling of Deformation Mechanisms in a Mg-3Al-1Zn Alloy under Biaxial Tension

Crystal Anisotropy of AZ31 Magnesium Alloy under Uniaxial Tension and Compression

On twinning and anisotropy in rolled Mg alloy AZ31 under uniaxial tension

Twinning Deformation and Yield Asymmetry Improvement of Magnesium Alloys by Free-End Torsion

{101¯2} Twinning Behavior under Biaxial Tension of Mg–3Al–1Zn Plate

Mechanical Behavior and Microstructural Characteristics of Magnesium Alloy Containing {10-12} Twin Lamellar Structure

Study of Twinning Behavior of Az31 Mg Alloy During Plane Strain Compression

Role of {101‾2} Twinning in the Anisotropy and Asymmetry of AZ31 Magnesium Alloy under High Strain Rate Deformation

The Role of {10–12} Tensile Twinning in Plastic Deformation and Fracture Prevention of Magnesium Alloys

Three-dimensional study of grain scale tensile twinning activity in magnesium: A combination of microstructure characterization and mechanical modeling

{ 10 1 ̄ 2 } twinning behavior under biaxial tension of Mg–3Al–1Zn plate

Mechanical Anisotropy Induced by the Competition Between Twinning and Basal Slip of AZ31 Magnesium Alloy under Biaxial Tension

Deformation Dynamics in Pre-Twinned Mg-3Al-1Zn Alloy: A Synchrotron X-ray Study

Three-dimensional study of grain scale tensile twinning activity in Mg: A combination of microstructure characterization and mechanical modeling

Twinning Characteristic in Tension of Magnesium Alloys and Its Effect on Mechanical Properties

Ex-situ EBSD Analysis of Yield Asymmetry, Texture and Twinning Development in Mg–5Li–3Al–2Zn Alloy During Tensile and Compressive Deformation

Quasi in Situ Observation of Twinning Evolution During Strain Path Change in Magnesium Alloy

Towards understanding double extension twinning behaviors in magnesium alloy during uniaxial tension deformation

Identification and Analysis of Anomalous {101‾2} Twins in an Extruded Mg-2wt%Y Alloy Sheet During Uniaxial Tensile Loading

Investigation of the Microstructural Evolution of the As-Extruded Mg–6Zn–1Mn Alloy Sheets under High Strain Rate Tensile Loading