Abstract:To further clarify the effect mechanism of MoS 2 element diffusion on tribological properties of cemented carbide materials, an investigation was carried in this study. The diffusion process between cemented carbide inserts and MoS 2 powder under high temperature condition was carried out in a muffle furnace device. The surface morphology and chemical element content of test samples were observed and measured with scanning electron microscope, energy spectrum, and X-ray diffraction instruments. The kinetics of the diffusion process was quantitatively discussed by thermodynamic experiments. Tribological experiments were carried out using friction and wear machine with which the friction coefficient and wear scar were obtained. The experimental results show that high temperature has a significant effect on physical and mechanical properties of cemented carbide materials. Moreover, MoS 2 elements diffusion on sample surface is existed and induced by thermal action, which results in a further changing of material properties of cemented carbide. The WC grain growth is inhibited when molybdenum element is only infiltration on sample surface at 500 °C, which improves the surface morphology and hardness of test sample. However, the oxidation rate, friction coefficient, and wear rate of test sample are the highest when heating temperature larger than 500 °C. The main reason is that, as the temperature increasing, the diffusion of sulfur elements is occurred and intensified the loss of cobalt element on sample surface. So, the bonding ability of it is decreased due to the loss of bonding phase Co. Thus, the surface hardness and wear resistance of test sample is deteriorated. This study provides a theoretical foundation for the application of molybdenum disulfide in tool cutting lubrication condition.

An Experimental Investigation of Element Diffusion and Mechanical Properties of Solid WC/Co Carbide Tool in High-Speed Milling Ti6Al4V

Diffusion Behavior and Wear Mechanism of WC/Co Tools when Machining of Titanium Alloy

Diffusion Wear in Dry Cutting of Ti–6Al–4V with WC/Co Carbide Tools

Molecular dynamics simulation of the diffusion behaviour between Co and Ti and its effect on the wear of WC/Co tools when titanium alloy is machined

Investigation on the Performance of Spark Plasma Sintered Ultrafine WC-Co Cemented Carbide End Mills During High-Speed Precision Milling of Ti-6Al-4V Alloy

Experimental Investigation on Tool Wear in Ultrasonic Vibration-Assisted Turning of SiCf/SiC Ceramic Matrix Composite

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Wear Mechanisms of Cemented Carbide Tools in Dry Cutting of Precipitation Hardening Semi-Austenitic Stainless Steels

Analysis of tool wear of TiAlN coated tool, machined surface morphology and chip during titanium alloy milling

Analysis on the Wear Performances of Cemented Carbide Tools Containing Ti in the Coatings When Machining Ti-6Al-4V Alloys

Study on the adhering failure mechanism of cemented carbide inserts and element diffusion model during the heavy-duty cutting of water chamber head

Microstructural Evolution and Mechanical Properties of Diffusion Bonding WC-Co Cemented Carbide to Steel Using Co and Composite Ni/Co Interlayers

Experimental Investigation and Numerical Simulation on Interfacial Carbon Diffusion of Diamond Tool and Ferrous Metals

Ultrafine WC–Co cemented carbide end mills prepared by spark plasma sintering and wear mechanism in milling of AISI H13

Influence of cutting parameters on PCD tool wear during milling tungsten carbide

Effect of Rapid Cooling on Microstructure and Properties of Nanocrystalline Wc-9%Co-Cr3c2-Vc Cemented Carbide

Diffusion Thermodynamic Behavior of Milling Ti-6A1-4V Alloy in Liquid Nitrogen Cryogenic Cooling

Residual Thermal Stress, Fracture Toughness, and Hardness in WC-Co Cemented Carbide: Finite Element Simulation and Experimental Verification

Effect of MoS 2 element diffusion under high temperature condition on the tribological properties of cemented carbide materials

Effect of Particle Size on Microstructure and Element Diffusion at the Interface of Tungsten Carbide/High Strength Steel Composites

Tool Life and Wear of WC–TiC–Co Ultrafine Cemented Carbide During Dry Cutting of AISI H13 Steel