Abstract:Long‐time austempering treatment can reduce the volume fraction of brittle martensite. However, the cementite precipitates in the austenite during the long‐time austempering process, which decreases the carbon content in retained austenite (RA) and consequently reduces the mechanical stability of RA. In comparison, excellent mechanical properties were obtained in the samples after short‐time austempering plus tempering treatment. Herein, the microstructure and mechanical properties of a high‐carbon bainitic steel treated by long‐time bainitic austempering and short‐time austempering plus tempering processes are compared. The multiphase microstructures are characterized by dilatometry, X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy to correlate with mechanical properties. Results show that although long‐time austempering treatment can reduce the volume fraction of brittle martensite, no significant improvement is observed in fracture damage resistance. Besides, the cementite is prone to precipitation from the austenite at the later period of the long‐time austempering process. The cementite precipitation in austenite decreases the carbon content in retained austenite (RA) and consequently reduces the mechanical stability of RA. In contrast, the cementite has not been able to precipitate from austenite after short‐time austempering treatment, whereas the martensite is softened and the stability of RA is improved during subsequent tempering. Therefore, excellent mechanical properties are obtained in the samples treated by short‐time austempering plus tempering process: ultimate tensile strength, 1489 MPa, yield strength, 1014 MPa, total elongation, 33.2%, and the product of strength and elongation (PSE) of 48.4 GPa%, where PSE is increased by 27% compared with the sample after long‐time bainitic austempering.

Thermal Stability Of Retained Austenite In High-Carbon Steels During Cryogenic And Tempering Treatments

Influence of Tempering and Cryogenic Treatment on Retained Austenite and Residual Stresses in Carbonitrided 18CrNiMo7-6 Low Alloy Steel

Stability of retained austenite in high carbon steel – Effect of post-tempering heat treatment

Effects of Sub-zero Celsius Treatment and Tempering on the Stability of Retained Austenite in Bearing Steel

Enhancing Ductility of Martensitic Steels Through Cryogenic Treatment

Effect of Tempering on Stability of Retained Austenite and Tensile Properties of Nanostructured Bainitic Steel

Nano-indentation Investigation on the Mechanical Stability of Individual Austenite in High-Carbon Steel

Effect of Rapid Tempering at High Temperature on Microstructure, Mechanical Properties and Stability of Retained Austenite of Medium Carbon Ultrafine Bainitic Steel

Characteristic of Retained Austenite Decomposition During Tempering and Its Effect on Impact Toughness in Sa508 Gr.3 Steel

Thermal stability of retained austenite in bainitic steel: an in situ study

Effects of Different Heat Treatments on Transformation of Residual Austenite in Bearing Steel

Effects of deep cryogenic treatment on the microstructure and mechanical properties of an ultrahigh-strength TRIP-aided bainitic steel

Improving the Cryogenic Strength–Ductility–Toughness of Multi‐Alloy Steel by Optimizing the Feature of Retained Austenite

Effects of traditional heat treatment and a novel deep cryogenic treatment on microstructure and mechanical properties of low-carbon high-alloy martensitic bearing steel

Influence of partitioning effects on the retained austenite content and properties of martensitic stainless steel

Thermo-stability of Ultra-fine Microstructures in Low Carbon Microalloyed Steel

The Role of Retained Austenite on the Mechanical Properties of a Low Carbon 3Mn-1.5Ni Steel

Tempering Stability of Retained Austenite in Nanostructured Dual Phase Steels

Effect of multiple deep cryo-treating and tempering on microstructure and property evolution of high carbon bearing steel

Comparison of Microstructure and Mechanical Properties of a High‐Carbon Bainitic Steel Treated by Long‐Time Bainitic Austempering and Short‐Time Austempering Plus Tempering Processes

Tempering Effects on the Stability of Retained Austenite and Mechanical Properties in a Medium Manganese Steel