Abstract:Selective laser melting (SLM) of aluminium alloys is of research interest due to its potential benefits in fabricating complex components for aerospace and automotive industries. In order to improve the mechanical properties and demonstrate the credibility of selective laser melted (SLMed) Al alloys, the effects of post heat treatment on the microstructures and mechanical properties need to be studies. In the present work, the nano-TiB2 decorated Al–7Si–Cu–Mg samples were successfully fabricated using the SLM technique, and then post-treated by direct ageing and conventional T6 heat treatment. The as-built TiB2/Al–7Si–Cu–Mg sample exhibits fine equiaxed grain structures without preferred crystallographic texture due to the high cooling rate of SLM and the addition of nano-TiB2 particles. Nano-scale eutectic Si cells are present within the equiaxed grains. Inside the cells, there are dislocation tangles without precipitates. After direct ageing treatment, the grain and cell structures remain almost unchanged, and the new Al2Cu, Mg2Si, and Si phases are formed around the dislocations. While after T6 treatment, the fine grains grow up and the eutectic Si phases coarse leading to the broken of cell structures. Besides, the as-built TiB2/Al–7Si–Cu–Mg samples show high tensile strength and ductility (yield strength: 297.2 MPa, ultimate tensile strength: 474.6 MPa, elongation: 13.4%). During ageing, the yield strength is enhanced by ~35% due to precipitation hardening effect. While the broken of fine microstructure during T6 leads to the decrease of yield strength by ~16%. The microstructure development and preliminary strengthening mechanism were discussed. The effect of post-heat treatments can yield the SLMed TiB2/Al–7Si–Cu–Mg samples with appropriate mechanical properties, promoting a wide range of applications.

Microstructure and inclusion of Ti–6Al–4V fabricated by selective laser melting

A Novel Approach to In-Situ Fabricate Ti-6Al-4V Alloy with Graded Microstructure and Property by Selective Laser Melting

Selective laser melting processing of heterostructured Ti6Al4V/FeCoNiCrMo alloy with superior strength and ductility

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Tensile Behavior of Ti-6Al-4V Alloy Fabricated by Selective Laser Melting: Effects of Microstructures and As-Built Surface Quality

Microstructure, solidification behavior and mechanical properties of Al-Si-Mg-Ti/TiC fabricated by selective laser melting

Selective laser melted near-beta titanium alloy Ti-5Al-5Mo-5V-1Cr-1Fe: Microstructure and mechanical properties

Microstructure and Mechanical Property of Ti–5Al–5Mo–5V–3Cr–1Zr Alloy Fabricated by Selective Laser Melting with a Preheated Substrate

Process Optimization and Microstructure Characterization of Ti6Al4V Manufactured by Selective Laser Melting

Microstructural Characteristics and Material Failure Mechanism of SLM Ti-6Al-4V-Zn Alloy

Microstructure, heat treatment and mechanical properties of TiB2/Al–7Si–Cu–Mg alloy fabricated by selective laser melting

Microstructure and mechanical deformation behavior of selective laser melted Ti6Al4V ELI alloy porous structures

Selective Laser Melting of High-Strength TiB2/AlMgScZr Composites: Microstructure, Tensile Deformation Behavior, and Mechanical Properties

Effects of Defects and Microstructures on Tensile Properties of Selective Laser Melted Ti6Al4V Alloys Fabricated in the Optimal Process Zone

Microstructural characteristic and mechanical properties of titanium-copper alloys in-situ fabricated by selective laser melting

Microstructural evolution and mechanical properties of selective laser melted Ti-6Al-4V induced by annealing treatment

Effect of In-Situ TiB2 Particles on Microstructure and Mechanical Properties of Al–Fe–Ni Manufactured by Selective Laser Melting

An investigation of ductile fracture behavior of Ti6Al4V alloy fabricated by selective laser melting

Hierarchical microstructure and strengthening mechanism of Cu-36.8Fe alloy manufactured by selective laser melting

Evolution of the Microstructure and Optimization of the Tensile Properties of the Ti–6Al–4V Alloy by Selective Laser Melting and Heat Treatment

Selective Laser Melting Enabled Additive Manufacturing of Ti-22Al-25Nb Intermetallic: Excellent Combination of Strength and Ductility, and Unique Microstructural Features Associated