Abstract:Li–CO2 batteries have recently attracted attention as promising candidates for next-generation energy storage devices due to their extremely high theoretical energy density. The real application of Li–CO2 cells involves addressing several drawbacks, including high charging potential, poor coulombic efficiency, and low rechargeability. Molybdenum disulfide supported on carbon nanotubes (MoS2/CNT) with various ratios functioned as a cathode catalyst for Li–CO2 batteries. The optimal MoS2/CNT composite achieved a maximum discharge capacity of 8551 mAh g–1 with a coulombic efficiency of 96.7%. This hybrid also obtained an initial charging plateau of 3.87 V at a current density of 100 mA g–1 with a cutoff capacity of 500 mAh g–1. It provided ideal electrochemical stability of 142 cycles at the current densities of 100 mA g–1, which was comparable with that of some precious metal catalysts. This optimized MoS2/CNT was also cycled at 200 and 400 mA g–1 for 112 and 55 times, respectively. Density functional theory calculations demonstrated that the sulfided Mo-edge (s-Mo-edge) on MoS2 materials showed appropriate adsorption strengths of Li, CO2, and Li2CO3. Moreover, joint results of Raman profiles and extended X-ray absorption fine structure spectra elucidated that the catalytic efficiencies of MoS2/CNT hybrids were proportional to the quantities of exposed s-Mo-edge active sites.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c17942?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c17942</a>.Computational method; XPS spectra of bare MoS2 and MoS2/CNT catalysts (Figure S1); full discharge–charge profiles of bare CNT and bare MoS2 cathodes (Figure S2); SEM with elemental mapping spectra of bare MoS2 and MoS2/CNT catalysts (Figure S3); electrochemical impedance spectroscopy of bare MoS2 and MoS2/CNT cathodes (Figure S4); cycling performances of bare CNT, MoS2/CNT, and MoS2-CNT cathodes (Figure S5–S7, S9); photograph and XRD diagrams of electrodes after the cycling measurement (Figure S8); high-resolution Mo 3d XPS spectrum of MoS2/CNT cathode (Figure S10); calculated adsorption energies of Li, CO2, and Li2CO3 on different sites of MoS2 (Figure S11–S13); charge density difference of CO2 on different sites of MoS2 (Figure S14); comparisons of electrochemical performances with previous studies (Table S1); and fitting parameters for Mo EXAFS spectra (Table S2) (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c17942/suppl_file/am0c17942_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

O2 Adsorption Associated with Sulfur Vacancies on MoS2 Microspheres

Three-Dimensional Carbon-Supported MoS2 with Sulfur Defects As Oxygen Electrodes for Li-O2 Batteries

Strong Surface‐Bound Sulfur in Conductive MoO2 Matrix for Enhancing Li–S Battery Performance

Synergistically creating sulfur vacancies in semimetal-supported amorphous MoS2 for efficient hydrogen evolution

Identification of Co-O-Mo Active Centers on Co-Doped MoS2 Electrocatalyst

Identification of Co–O–Mo Active Centers on Co-Doped MoS<sub>2</sub> Electrocatalyst

Unraveling States, Energetics, and Kinetics of Adsorbing Oxygen Species above MoS2

Enhanced catalysis LiS<sub>3</sub> of radical-to-polysulfide interconversion <i>via</i> increased sulfur vacancies in lithium-sulfur batteries

The Impact of Oxygen Content in O‐Doped MoS2 on the Kinetics of Polysulfide Conversion in Li–S Batteries

Efficacious nitrogen introduction into MoS2 as bifunctional electrocatalysts for long-life Li-O2 batteries

High Resolution Electrochemical Imaging for Sulfur Vacancies on 2D Molybdenum Disulfide

Activating MoS 2 Nanoflakes via Sulfur Defect Engineering Wrapped on CNTs for Stable and Efficient Li‐O 2 Batteries

Mo2C-MoP heterostructure regulate the adsorption energy of electrocatalysts in high-performance Li-S batteries

Catalytically Active Site Identification of Molybdenum Disulfide as Gas Cathode in a Nonaqueous Li–CO 2 Battery

Oxygen Defect‐Rich WO3−x–W3N4 Mott–Schottky Heterojunctions Enabling Bidirectional Catalysis for Sulfur Cathode

Role of sulfur vacancies in MoS2 monolayers in stabilizing Co atoms for efficient CO oxidation

Oxygen Deficiency Driven Conversion of Polysulfide by Electrocatalysis: MoO3‐x Nanobelts for an Improved Lithium‐Sulfur Battery Cathode

In-situ transformation into MoP/MoS 2 heterogeneous structure with rich S-vacancy enhanced hydrogen evolution reaction

Rapid hydrogen adsorption-desorption at sulfur sites via an interstitial carbon strategy for efficient HER on MoS 2

Unraveling Polysulfide's Adsorption and Electrocatalytic Conversion on Metal Oxides for Li‐S Batteries

Engineering metal-sulfides with cations-tunable metal-oxides electrocatalysts with promoted catalytic conversion for robust ions-storage capability