Abstract:The quenching and partitioning (Q&P) process is a promising method to create novel martensitic steels with improved balance of strength and ductility by retaining considerable amount of austenite in martensitic matrix. This kind of microstructure provides suitable condition to study wear and abrasion mechanism since the effect of retained austenite on the wear property of martensitic steel is still controversial by now. Selecting traditional quenching and tempering (Q&T) sample with identical composition Fe-0.4C-1.5Mn-1.5Si as reference, the dry sliding wear property of Q&P samples with different austenitization temperatures was studied. The results show that the volume fraction of retained austenite in Q&P samples with full austenitization at 860 or 1000 degrees C respectively is nearly the same (about 14.37% in the former and about 13.79% in the later), and the corresponding carbon concentration (mass fraction) in retained austenite is relatively high (1.37% in the former and 1.38% in the later). Under the conditions of low loading (50 N) and slide speed (40 mm/s), it is not easy to induce martensitic transformation because of very strong mechanical stability, leading to the low friction and wear resistance of samples. The slight better wear resistance of samples with low austenitization temperature can be attributed to microstructural refinement. When the austenitization temperature was 800 degrees C, the intercritical Q&P samples were obtained. Microstructure analysis indicates there exist the highest volume fraction of retained austenite (about 22.28%) and a small volume fraction of ferrite (about 6.75%) in martensitic matrix, which results in the lowest microhardness among present four kinds of samples. However, the mechanical stability of retained austenite in this kind of sample is weak due to the low carbon concentration (about 1.06%). The obvious martensitic transformation accompanying sliding wear contributes to extra hardening and provides additional compressive stress on the touching surface caused by volume expansion. Therefore, the intercritical Q&P samples exhibit the best wear resistance. Based on the experimental results, it is true that the mechanical stability instead of the amount of retained austenite in martensitic steel plays a critical role in improving wear resistance.

The Properties and Residual Stress of Argon Arc Cladding Metal by Low Temperature Martensitic Transformation Powder

Temperature Field Simulation and Experimental Analysis of Laser Cladding 45 Steel.

Effect of medium entropy alloy powder-core wire on friction wear and corrosion resistance of arc cladding additive layer

Influence of Heat Treatment on Microstructure and Mechanical Properties of Laser Cladding Coatings

Microstructure stability and high temperature wear behavior of an austenite aging steel coating by laser cladding

Study on ductile iron surface laser cladding austenitic stainless steel coating heat treatment to enhance wear resistance

Martensite transformation characteristics in the heat affected zone of laser cladding on rail

Microstructure Evolution During Laser Cladding Fe-Cr Alloy Coatings on Ductile Cast Iron

Study on the microstructure and heat affected zone of nickel-based alloy cladding layer

Microstructure and mechanical properties of stainless steel clad plate welding joints by different welding processes

Transformation law of microstructure evolution and mechanical properties of electron beam freeform fabricated 321 austenitic stainless steel

Effect of Austenite Reversion Treatment and Partitioning on the Phase Transformation Behavior and Mechanical Properties of Martensitic–Austenitic CrMnNi‐Cast Steel

Effect of intrinsic thermal cycles on the microstructure and mechanical properties of heat affect zones in laser cladding coatings on full-scale rails

Structural Evolution and Tribological Properties of WC Particles-Strengthened Nickel-Based Cladding Layers

Material Tests of 316L Austenitic Stainless-Clad Steel at Elevated Temperatures

Microstructure and Properties of a 2.25Cr1Mo0.25V Heat-Resistant Steel Produced by Wire Arc Additive Manufacturing

Mechanical Behavior and Fatigue Performance of Austenitic Stainless Steel under Consideration of Martensitic Phase Transformation

Effect of Austenitization Temperature on the Dry Sliding Wear Properties of a Medium Carbon Quenching and Partitioning Steel

Influence of Heat Treatment on Microstructures and Mechanical Properties of K447A Cladding Layers Obtained by Laser Solid Forming

The effect of short-term annealing in an Ar environment on microstructure and adhesion property of Cr-coated Zircaloy-4 claddings

Investigation on Mechanical Properties and Corrosion Resistance of Cobalt-Based Alloy Cladding Layer