Abstract:In order to investigate the effect of grain boundaries on the mechanical response in the micrometer and submicrometer levels, complementary experiments and molecular dynamics simulations were conducted on a model bcc metal, tantalum. Microscale pillar experiments (diameters of 1 and 2 μm) with a grain size of ~100–200 nm revealed a mechanical response characterized by a yield stress of ~1500 MPa. The hardening of the structure is reflected in the increase in the flow stress to 1700 MPa at a strain of ~0.35. Molecular dynamics simulations were conducted for nanocrystalline tantalum with grain sizes in the range of 20–50 nm and pillar diameters in the same range. The yield stress was approximately 6000 MPa for all specimens and the maximum of the stress–strain curves occurred at a strain of 0.07. Beyond that strain, the material softened because of its inability to store dislocations. The experimental results did not show a significant size dependence of yield stress on pillar diameter (equal to 1 and 2 um), which is attributed to the high ratio between pillar diameter and grain size (~10–20). This behavior is quite different from that in monocrystalline specimens where dislocation ‘starvation’ leads to a significant size dependence of strength. The ultrafine grains exhibit clear ‘pancaking’ upon being plastically deformed, with an increase in dislocation density. The plastic deformation is much more localized for the single crystals than for the nanocrystalline specimens, an observation made in both modeling and experiments. In the molecular dynamics simulations, the ratio of pillar diameter (20–50 nm) to grain size was in the range 0.2–2, and a much greater dependence of yield stress to pillar diameter was observed. A critical result from this work is the demonstration that the important parameter in establishing the overall deformation is the ratio between the grain size and pillar diameter; it governs the deformation mode, as well as surface sources and sinks, which are only important when the grain size is of the same order as the pillar diameter.

Strain Accommodation of <110>-Normal Direction-Oriented Grains in Micro-Shear Bands of High-Purity Tantalum

Strain Path Dependence of Microstructure and Annealing Behavior in High Purity Tantalum

Deformation Mechanism of Metastable Oriented Grains in High-Purity Tantalum under Different Strain Paths

Orientation-dependent grain boundary characteristics in tantalum upon the change of strain path

Analysis of Stored Energy Distribution in Three Directions of Tantalum in Deformed and Annealed States

Quasi-in-situ study on the crystallographic lattice rotation of tantalum during compression deformation

Effect of strain path change on the through-thickness microstructure during tantalum rolling

Molecular Dynamics Simulation of Nanocrystalline Tantalum under Uniaxial Tension

Crystallographic analysis of nucleation for random orientations in high-purity tantalum

Microstructural and texture evolution investigation of laser melting deposited TA15 alloy at 500?C using in-situ EBSD tensile test

Microstructure and Strength of a Tantalum-Tungsten Alloy after Cold Rolling from Small to Large Strains

Micro-Mechanical Response of Ultrafine Grain and Nanocrystalline Tantalum

Study on the Grain Rotation of High-Purity Tantalum during Compression Deformation

Processing of bulk nanolamellar tantalum and justification of strengthening by grain boundary pre-stressed model

Effects of Initial Textures on the Microstructure and Annealing Behavior of Tantalum after Dynamic Plastic Deformation

A comparative study of clock rolling and unidirectional rolling on deformation/recrystallization microstructure and texture of high purity tantalum plates

Character and Distribution of Geometrically Necessary Dislocations in Polycrystalline Tantalum

Quantitative Analysis: How Annealing Temperature Influences Recrystallization Texture and Grain Shape in Tantalum

Size Effects on the Tensile Properties and Deformation Mechanism of Commercial Pure Titanium Foils

The orientation spreading in γ-fiber of electron beam melted Ta-2.5W alloy during cold rolling

Texture Evolution of High Purity Tantalum under Different Rolling Paths