Abstract:OBJECTIVE:To investigate influence of setting time on bond strength of different bioactive pulp capping materials with self-etch or etch-and-rinse adhesive.METHODS:Sixty specimens were prepared for each of the three tested capping materials, namely mineral trioxide aggregate (MTA), iRoot BP Plus (BP) and iRoot FS (FS). Specimens of each material were divided into three groups and bonded at three setting time points of the materials respectively: initial setting time (4 h for MTA, 2 h for BP and 20 min for FS), 24 h after application and 7 d after application. The specimen surfaces of each group were treated with self-etch mode or etch-and-rinse mode of one universal adhesive (Single Bond Universal, SBU) (n=10). The bonding area was restricted to a round area with 3 mm diameter, on which composite cylinders were build up with flowable composite and light cured completely. The shear bond strength was tested immediately with a shear strength tester and fracture mode was observed under stereo microscope and recorded. The mean shear bond strength for each group was analyzed with SPSS 19.0 software ANOVA method. The surface morphology of each material was observed after setting and acid treatment under scanning electron microscope.RESULTS:There was no significant difference among the three tested materials at either initial setting point or 7 d after application (P<0.05). The bond strength of MTA was significantly higher than those of BP and FS 24 h after application in both bonding modes (P<0.05). For all the three tested materials, shear bond strength was significantly higher for complete setting group than for initial setting group of the same material (P<0.05). Under scanning electron microscope, the characteristic crystal patterns could be observed on the three bioactive materials surfaces after complete setting, the size of which was bigger for MTA than for BP and FS. These features were lost to some extent after self-etch primer application or phosphoric acid etching.CONCLUSION:Based on the present results, adequate bond strength can be obtained for FS at initial setting time, which is comparable with BP and MTA. This implies that clinically composite restoration can be placed over bioactive direct capping materials after shortened initial setting process in one visit.

Effects of bond strength evaluation on different durations of adult permanent teeth and youth permanent teeth by using universal adhesives to dentin

Influence of Casein Phosphopeptide-Amorphous Calcium Phosphate Application, Smear Layer Removal, and Storage Time on Resin-Dentin Bonding

Bonding Effectiveness of the Universal Adhesive on Caries-Affected Dentin of Deciduous Teeth

Durability of Four Composite Resin Cements Bonded to Dentin under Simulated Pulpal Pressure

The influence of caries-affected dentin on bonding effect of deciduous teeth

[Effects of Three Self-Etch Adhesives and Mild Salivary Contamination on the Bonding Durability of Deciduous Teeth].

[Effects of Application Methods of Self-Etching Adhesives on Resin-Dentin Bonding].

The Effect of Treating Time on the Shear Bond Strength of the Seventh Generation of Adhesive

A Research on Bond Strength and Interface of Dentin Adhesives

Effect of Chemical Removal or Mechanical Modification of Smear Layer on Dentin Adhesion with Universal Resin Adhesives

Defying ageing: An expectation for dentine bonding with universal adhesives?

Effect of curing modes and light-cure times on microtensile bond strength of adhesives

Influence of adhesive systems containing different functional monomers on the longevity of bond strength at different dentin depths

Effect of Smear Layer Prepared by Different Burs on the Microtensile Bond Strengths of Two Kinds of Adhesive Systems to Human Dentin

Comparative evaluation of bonding performance between universal and self-etch adhesives: In vitro study

[Influence of Setting Time on Bond Strength of Different Bioactive Pulp Capping Materials with Dental Adhesive].

Promoting Bond Durability by a Novel Fabricated Bioactive Dentin Adhesive

Influence of Peripheral Enamel Bonding and Chlorhexidine Pretreatment on Resin Bonding to Dentin.

Shear bond strength of universal adhesives to human enamel and dentin

Effect of Active Bonding Application after Selective Dentin Etching on the Immediate and Long-Term Bond Strength of Two Universal Adhesives to Dentin

Experimental study of bonding strength between resin composite direct core build-up materials and dentin in vitro