Abstract:IntroductionIn this study, the silk fibroin blended constructs were produced, scaffold performances of different kinds of scaffold were analyzed, and the better type for tissue engineering was optimized.MethodsThe silk fibroin/collagen (SF/C) and silk fibroin/chitosan (SF/CS) were made using a freeze-drying technique, porosity, water absorption expansion rate, mechanical properties and pore size of different scaffold was detected. Bone marrow mesenchymal stem cells (BMSCs) of 4-week-old male Wistar rats were separated by density gradient centrifugation, third generation BMSCs were seeded onto scaffolds, cultured 14 days, proliferation and metabolize of cells were detected in different time using the thiazolyl blue tetrazolium bromide (MTT) assay method, and cell morphology and distribution were observed by histological analysis and scanning electron microscopy (SEM).ResultsPorosity, water absorption expansion rate and Young’s modulus of SF/C were significantly higher than SF/CS (p < 0.05); pore size of SF/C and SF/CS was 103 ± 12 and 76 ± 11 μm and had no significant differences between two types (p > 0.05); MTT results showed that the metabolism of cells in the SF/C was better than SF/CS; after cultivation for 14 days, in the inner zone of scaffolds, cells staining were little or absent from SF/CS, lots of cells staining were existing in SF/C; pore size was consistent, holes communicated with each other better, stem cells grew well inside the scaffolds, extended fully and secreted much extracellular matrix under SEM in SF/C scaffold; internal structure of SF/CS was disorder, holes size were not consistent, and did not communicated with each other and cells were partly dead.ConclusionCompared with SF/CS, SF/C scaffold showed better porosity, water absorption expansion rate, elasticity modulus and pore size, cells grow well inside the scaffolds, and was more suitable for tissue engineering.

Silk Scaffolds with Gradient Pore Structure and Improved Cell Infiltration Performance.

Silk fibroin/sodium alginate composite nano-fibrous scaffold prepared through thermally induced phase-separation (TIPS) method for biomedical applications

A Novel Layer-Structured Scaffold with Large Pore Sizes Suitable for 3D Cell Culture Prepared by Near-Field Electrospinning

Structure-induced Cell Growth by 3D Printing of Heterogeneous Scaffolds with Ultrafine Fibers

A Review for Fabrication of Large Pores in Electrospun Scaffolds for Tissue Engineering

Creation of Macropores in Electrospun Silk Fibroin Scaffolds Using Sacrificial PEO-microparticles to Enhance Cellular Infiltration.

Preparation of the Silk Fibroin 3D Scaffolds with Large Pore Sizes and High Interconnectivity

Electrospun Fibrous Mats with High Porosity As Potential Scaffolds for Skin Tissue Engineering

Applications of electrospun scaffolds with enlarged pores in tissue engineering

Silk Fibroin Tissue Engineering Scaffolds with Aligned Electrospun Fibers in Multiple Layers

Electrospun silk fibroin/SIS-dECM hierarchical scaffolds for cell growth

Facile Synthesis of 3D Silk Fibroin Scaffolds with Tunable Properties for Regenerative Medicine

Co-electrospun Nano-/Microfibrous Composite Scaffolds with Structural and Chemical Gradients for Bone Tissue Engineering.

Hierarchical Macro/micro-Porous Silk Fibroin Scaffolds for Tissue Engineering

A Biomimetic Silk Fibroin/Sodium Alginate Composite Scaffold for Soft Tissue Engineering

3D Nanofiber Scaffolds from 2D Electrospun Membranes Boost Cell Penetration and Positive Host Response for Regenerative Medicine.

Three-dimensional tissue engineering scaffolds with electrospinning technique：application and prospects

Enhanced Cellular Infiltration of Tissue-Engineered Scaffolds Fabricated by PLLA Nanogrooved Microfibers

Electrospun Fibrous Scaffolds with Continuous Gradations in Mineral Contents and Biological Cues for Manipulating Cellular Behaviors.

Bacterial Cellulose Nanofibers Promote Stress and Fidelity of 3D-Printed Silk Based Hydrogel Scaffold with Hierarchical Pores

Silk fibroin/collagen and silk fibroin/chitosan blended three-dimensional scaffolds for tissue engineering