Abstract:The micellization of a polystyrene-b-poly(dimethylsiloxane) (PS-b-PDMS) diblock copolymer with the number-average molecular weights (M-n) of 193 000 g/mol for PS block and 39 000 g/mol for PDMS block and the glass transition behavior of the PS blocks in the cores of collapsed dry micelles with PDMS tethered coronae were studied. A range of micelle morphologies was observed by varying the micellization conditions and varying the ratio of the methylene chloride (MC) solvent and the n-dodecane (D) selective nonsolvent. MC is a solvent for both of the blocks, but D is a selective solvent for only the PDMS block. After completely removing the solvents below the glass transition temperature (T-g) of the initially solvated PS blocks in MC via extraction and vacuum-drying, the collapsed dry micelles, which were originally spheres and cylinders, became "tablets" or "ribbons". The diameters of the "tablets" and widths of the "ribbons" were approximately 50 and 100 nm, respectively. The thicknesses of these textures ranged from 20 to 40 nm. The PS block cores of the dried micelles exhibited a Tg very close to that of the homo-PS bulk samples with the same M-n. However, for a broad temperature range below the T-g(PS), the collapsed dry micelles possessed heat capacity (C-p) values higher than the addition scheme calculated Cp based on PS and PDMS in their solid and liquid bulk states; whereas the C-p values of the liquid state above the T-g(PS) fit well with the calculated data. These observations support the idea of PS interface layers with mobility induced by the liquid PDMS coronae such that only the inner cores of the PS blocks were in the glassy state. In a temperature region between 0 and 50 degreesC, the lower limit of the interface thickness (i.e., assuming that the mobile PS layers possessed the same mobility as the PS liquid) was estimated to be approximately 2 nm for the collapsed dry micelles. The interface thickness slightly increased with increasing temperature.

Grafting density dominant glass transition of dry polystyrene brushes.

Influence of grafting on the glass transition temperature of PS thin films

Effects of molecular weight and interaction parameter on the glass transition temperature of polystyrene mixtures and its blends with polystyrene/poly (2,6-dimethyl-p-phenylene oxide)

Influence of Clay and Predispersion Method on the Structure and Properties of Polystyrene (ps)‐clay Nanocomposites

Effect of overall grafting density on microphase separation of mixed homopolymer brushes synthesized from Y-initiator-functionalized silica particles

Influence of Entanglements on Glass Transition of Atactic Polystyrene

Glass Transition Temperature of Polystyrene Microparticles

Effects of chain ends and densities on the glass transition of polymer thin films probed by linear and cyclic polystyrene

Enhanced Dynamics of PMMA Brushes Induced by the Chain Ends of a Flexible Polymer Chain

Density effects on collapse, compression and adhesion of thermoresponsive polymer brushes

Glass Transition of Expanded Polystyrene Coils

The Glass Transition Temperature of Poly(Phenylene Sulfide) with Various Crystallinities

Effect of Grafting Density on the Crystallization Behavior of Molecular Bottlebrushes

Glass Transition of Atactic Polystyrene with Less Chain Entanglements

Structure of polymer layers grafted to nanoparticles in silica-polystyrene nanocomposites

T-g Confinement Effect of Random Copolymers of 4-Tert-butylstyrene and 4-Acetoxystyrene with Different Compositions

Viscoelastic and dynamic properties of polymer grafted nanocomposites with high glass transition temperature graft chains

Polymer brushes with reversibly tunable grafting density

Thermal and Rheological Analysis of Polystyrene-Grafted Silica Nanocomposites

Excluded Volume Effects In Compressed Polymer Brushes: A Density Functional Theory

Glass Transition Behavior of Polystyrene Blocks in the Cores of Collapsed Dry Micelles Tethered by Poly(Dimethylsiloxane) Coronae in a PS-b-PDMS Diblock Copolymer