Abstract:Due to numerous merits, polyesters have been widely used for the preparation of porous scaffolds for biomedical applications. However, insufficient dimensional stability and weak cell interaction are two critical challenges to highly porous polyester scaffolds fulfilling their roles during applications. Here, we report the surface modification of PLGA scaffolds with air plasma for simultaneously tackling the dimensional shrinkage of PLGA scaffolds and improving scaffold-tissue integration. Highly porous PLGA scaffolds with interconnected pore structures and well orientated microtubules were prepared through lyophilization, and an air plasma process with varied duration was applied to the porous scaffolds. Water contact angle measurements indicated that moderate treatment (120 seconds) can significantly increase the wettability without distorting the morphology of and damaging the PLGA scaffolds. Further characterization (SEM, XPS, μ-CT, and theoretical computations) revealed that the plasma treatment enabled the generation of carboxyl groups on the surface of the PLGA scaffold, and the hydrophilic PLGA chain tends to extend under aqueous conditions in comparison to the hydrophobic pristine PLGA chain. Consequently, this could eliminate the hydrophobic-scaffold/water interface and weaken the driving force behind the distortion of the scaffolds in aqueous conditions, and finally inhibit overall shrinkage and maintain the microstructures of the porous scaffolds. Similar results were observed with porous PLA scaffolds, indicating the generality of air plasma treatment in inhibiting the shrinkage of polyester scaffolds. In the meantime, in vitro cell attachment experiments and in vivo subcutaneous implantation results consistently indicated that better maintaining the microstructure could significantly enhance the short-term cell attachment/proliferation on the scaffold and the long-term scaffold-tissue integration. These findings may inspire many creative and efficient strategies for the surface modification of polyester scaffolds to improve their performance for biomedical applications.

Surface modification of ultrahigh molecular weight polyethylene by plasma-induced in-situ grafting with vinyl triethoxysilane.

Synergetic enhancement of interfacial properties and impact resistant of UHMWPE fiber reinforced composites by oxygen plasma modification

Plasma functionalization of poly(vinyl alcohol) hydrogel for cell adhesion enhancement

Surface Modification and Adhesion Improvement of Expanded Poly(tetrafluoroethylene) Films by Plasma Graft Polymerization

Dielectric barrier discharge plasma treatment of ultrahigh molecular weight polyethylene in different discharge atmospheres at medium pressure: A cell-biomaterial interface study

Surface Modification of Poly(tetrafluoroethylene) Films Via Plasma Treatment and Graft Copolymerization of Acrylic Acid

Surface Antifouling Modification on Polyethylene Filtration Membranes by Plasma Polymerization

Superior Enhancement of the UHMWPE Fiber/Epoxy Interface through the Combination of Plasma Treatment and Polypyrrole In-Situ Grown Fibers

Surface Modification of Porous PLGA Scaffolds with Plasma for Preventing Dimensional Shrinkage and Promoting Scaffold-Cell/tissue Interactions

The mechanical properties of the ultra high molecular weight polyethylene grafted with 3-dimethy (3-(N-methacryamido) propyl) ammonium propane sulfonate

Surface modification of low temperature plasma-pretreated ePTFE film by AAc graft copolymerization

Chemical grafting for improved interfacial shear strength in UHMWPE/PVA-hydrogel fiber-based composites used as soft fibrous tissue replacements

Plasma surface modification technique–induced gelatin grafting on bio-originated polyurethane porous matrix: Physicochemical and in vitro study

Surface modification of ultra‐high molecular weight polyethylene fiber by different kinds of SiO2 nanoparticles

Structure Modification and Enhancement of Wear Resistance of Ultra-High-Molecular-Weight Polyethylene by Low-Pressure Helium Plasma Treatment

Surface Modification Of Vascular Endothelial Growth Factor-Loaded Silk Fibroin To Improve Biological Performance Of Ultra-High-Molecular-Weight Polyethylene Via Promoting Angiogenesis

TPU with outstanding wettability and hydrophilic stability is obtained by plasma-induced graft polymerization

Synergistically improving interface behavior by designing physical twisting structure and "rigid-flexible" interface layer on ultra-high molecular weight polyethylene (UHMWPE) fiber surface

A Universal Strategy for Rapid and Scalable Surface Modification of Ultra High Molecular Weight Polyethylene Fiber

Towards a methodology for the effective surface modification of porous polymer scaffolds

"Like binding a book": Interfacial improvement of pre-melted ultrahigh molecular weight polyethylene by pulse vibration molding