Abstract:Purpose: This study evaluated the computer-aided approach to the reconstruction of mandibular defects using a vascularized iliac-crest flap. Materials and Methods: From December 2015 to October 2016, 14 patients (8 men and 6 women) 18 to 64 years old (median age, 29 yr) were treated at the Peking University School and Stomatology Hospital (Beijing, China). Biopsy specimens from all patients were subjected to histologic examination before segmental mandibulectomy. Computer-based surgical techniques, including virtual surgical planning, computer-aided design and manufacturing, rapid prototyping, and intraoperative navigation, were used to restore the anatomic continuity and configuration of the mandible using a vascularized iliac-crest flap. Two transverse dimensions and 1 anteroposterior (A-P) dimension were evaluated based on the virtual plan and postoperative computed tomogram. Lines from condylar head to condylar head and from gonial angle to gonial angle were defined as the transverse dimensions. A perpendicular line drawn from the mandibular midline to the center point on the condylar head to condylar head measurement was defined as the A-P dimension. Complications were evaluated during follow-up. Results: The flap success ratewas 92.9% (13 of 14), with 1 flap failure. After the operation, there were no other serious complications in 13 of the 14 patients, who exhibited a good mandibular configuration with good occlusion. Furthermore, the height of bone graft was sufficient for implants. Healing of the recipient and donor sites with no serious complication was uneventful. The average surgical errors in the A-P dimension and transverse dimensions were 1.8 +/- 1.0 mm (range, 0.2 to 3.7 mm), 2.2 +/- 1.1 mm (range, 0.9 to 5.0 mm), and 2.6 +/- 1.6 mm (range, 0.3 to 7.2 mm), respectively. Conclusions: The use of these digital techniques was found to be a viable option for reconstruction of mandibular defects, but the results should be interpreted cautiously because of the small number of patients and the relatively short follow-up. (C) 2017 Published by Elsevier Inc on behalf of the American Association of Oral and Maxillofacial Surgeons

Reconstruction of Mandibular Contour Using Individualized High-Density Porous Polyethylene (medpor®) Implants under the Guidance of Virtual Surgical Planning and 3D-Printed Surgical Templates

[Application of Computer Aided Design/computer Aided Manufactured Techniques in Mandible Defect Reconstruction].

Application of CAD/CAM Techniques in Mandible Large-Scale Defect and Reconstruction with Vascularized Fibular Bone Graft

[Application of Computer Aided Design-Computer Aided Manufacture Technique in Mandible Defect Reconstruction with Individual Titanium Prosthesis].

Using Computer-Aided Design and Manufacture (CAD/CAM) Techniques to Accurately Reconstruct Defects of Mandibular Con-Tour with High-Density Porous Polyethylene(medpor?)

Accurate Reconstruction of Discontinuous Mandible Using a Reverse Engineering/computer-Aided Design/rapid Prototyping Technique: a Preliminary Clinical Study.

The use of modified 3D-printed reconstruction plates in mandible segmental defect rehabilitation: a case report

[Reconstruction of Mandibular Bone Defects Using Three-Dimensional Skull Model and Individualized Titanium Prosthetics from Computer Assisted Design].

Outcome Evaluation of Three-Dimensionally Printed Patient-Specific Surgical Plates for Mandibular Reconstruction

Clinical application of 3D-printed PEEK implants for repairing mandibular defects

Functional Reconstruction of Mandibular Segment Defects with Individual Preformed Reconstruction Plate and Computed Tomographic Angiography-Aided Iliac Crest Flap.

Titanium Mesh Scaffolding Iliac Crest Bone Grafts to Reconstruct Unilateral Large-Sized Mandibular Contour Defects: A New Approach of an Old Concept

Clinical application of individualized artifical mandible based on rapid prototyping technology

The Design and Biomechanical Evaluation of Individual Mandibular Prosthesis

Mandible Reconstruction Assisted by Preoperative Virtual Surgical Simulation

Immediate reconstruction of bilateral mandible defects: management based on computer-aided design/computer-aided manufacturing rapid prototyping technology in combination with vascularized fibular osteomyocutaneous flap.

Application of CAD/CAM-assisted Technique with Surgical Treatment in Reconstruction of the Mandible.

Translating Computer-Aided Design and Surgical Planning into Successful Mandibular Reconstruction Using a Vascularized Iliac-Crest Flap.

Design And Biomechanical Analysis Of A Novel Mandibular Prosthesis

Mandibular Reconstruction With Single Barrel Vascular Free Fibula Flap And Implants-Borne Fixed Prosthesis: Usage Of A Modified Healing Abutment

Clinical Application of Computer-assisted Three-dimensional Reconstruction Combined with 3D Printing in Mandibular Defect Reconstruction