Abstract:The cold rolling and intermediate annealing process, along with the incorporation of rare earth elements, play an important role in the microstructure, texture, and inhibitors of oriented silicon steel. Currently, there is limited research on the impact of rare earth yttrium on texture evolution during the cold rolling and intermediate annealing processes. Therefore, the effects of different cold rolling deformations and intermediate annealing temperatures on the microstructure and texture of Y bearing oriented silicon steel have been studied. The experimental results demonstrate that the average grain size of the intermediate annealed plate progressively decreases with increasing the cold rolling deformation. This is because the high cold rolling deformation brings more additional dislocations and distortions, consequently enhancing the driving force for recrystallization. Observing the microstructure with various cold rolling deformation, the results show that the annealed plate with a 72 % reduction rate exhibited the highest Goss texture percentage of 4.83 %. This is because the cold-rolled sheet with a reduction rate of 72 % exhibits an abundance of Goss oriented substructures. These substructures quickly dominate the {111} deformed matrix during the initial recrystallization, and promote grains nucleation and growth. As the annealing temperature increases, the driving force for the growth of recrystallized grains also increases, leading to a gradual increase in grain size. The plate annealed at 940 °C exhibits the highest percentage (4.83 %) of Goss texture. The addition of rare earth Y can lead to an increase in grain size in the intermediate annealed plate and facilitate the formation of {411} texture. This is advantageous for the abnormal growth of Goss texture. The results demonstrate that a cold rolling deformation rate of 72 % and an intermediate annealing temperature of 940 °C are good for promoting abnormal growth of Goss orientation. The study results on precipitation kinetics suggests that the grain boundary nucleation of AlN and dislocation nucleation of MnS are the most effective way of nucleation. The precipitates in oriented silicon steel without Y are Al 2 O 3 and MnS, while those in the samples with Y are AlN, YS, and YO x S y . The addition of rare earth Y leads to a reduction in both the density and size of precipitates. Moreover, With the increase of annealing temperature, the size of precipitates decreases and the amount of precipitates increases. Additionally, the addition of Y makes the steel more clean, meanwhile, the pinning effect of inclusions on grain boundaries is weakened. Therefore, the grain size of the steel with Y is larger.

Phenomenon and Cause Analysis of Different Secondary Recrystallization Behaviors in Thin-Gauge Grain-Oriented Silicon Steels

Effects of High-Temperature Annealing Atmosphere on the Secondary Recrystallization Behavior and Magnetic Properties of Fe-3.2%Si-0.055%Nb Grain-Oriented Silicon Steel

Effect of aluminum on secondary recrystallization texture and magnetic properties of grain-oriented silicon steel

Characteristic of Precipitate Evolution during High Temperature Annealing in Grain-Oriented Silicon Steel

Investigation of microstructure and texture as related to primary recrystallization of grain-oriented silicon steel

Complete Goss Secondary Recrystallization by Control of the Grain Size and Texture of Primary Recrystallization in Grain-Oriented Silicon Steel

Effect of heating rate of final annealing stage on secondary recrystallization in grain-oriented silicon steel

Investigation of Primary Recrystallization and Decarbonization with Different Heating Rates of Intermediate Annealing Using Nb-Containing Grain-Oriented Silicon Steel

The origin of {113} grains and their impact on secondary recrystallization in producing ultra-thin grain-oriented electrical steel

Coordinate regulation mechanism of primary recrystallization texture and microstructure of grain-oriented silicon steel

Effect of Gradient Heat Conduction on Secondary Recrystallization of Grain-Oriented Silicon Steel

Influence Mechanisms of Cold Rolling Reduction Rate on Microstructure, Texture and Magnetic Properties of Non-Oriented Silicon Steel

Effect of Secondary Cold Rolling Reduction Rate on Secondary Recrystallization Behavior of CGO Steel

Ultra‐Thin 3.5%Si Steel with Both Magnetic Properties and Mechanical Properties Produced by Different Process Routes of Large‐Scale Production

Dependence of recrystallization behavior and magnetic properties on grain size prior to cold rolling in high silicon non-oriented electrical steel

Effect of Slab Reheating Temperature on Cold Rolling Texture Evolution of Nb-Containing Grain-Oriented Silicon Steel

Effect of Slab Reheating Temperature on Recrystallization Microstructure, Texture and Magnetic Properties of Nb-containing Grain-Oriented Silicon Steel

Effect of intermediate annealing temperature and cold rolling deformation on the texture of yttrium bearing oriented silicon steel

Origin of fine equiaxed grains in industrial low-temperature grain-oriented silicon steel normalized sheet and their influence on magnetic properties

Effect of microstructure modification on magnetic and mechanical properties of high-grade non-oriented silicon steel during annealing treatment

Effect of recrystallization annealing temperature on microstructure, texture and magnetic properties of non-oriented silicon steel produced by strip casting