Abstract:Repetitive upsetting-extrusion (RUE) is known as a processing method that effectively improves the properties of a billet without changing its initial shape. In this paper, one pass RUE with reduced deformation temperature (re-upsetting at 360 °C and secondary extrusion at 340 °C) and different extrusion speeds (0.5 and 1 mm/s) is implemented to improve the strength and toughness of AZ80 Mg rods, and simultaneous reduction in tensile anisotropy is achieved. Influences of one pass RUE method on the resulting microstructure and texture evolution of the alloy are investigated alongside their correlated impact on its mechanical properties. After RUE processing, the grain structure of AZ80 alloy is characterized by numerous fine dynamic recrystallized (DRXed) grains, combined with large unDRXed grains obtained at high extrusion speed or coarse DRXed grain bands obtained at low extrusion speed. Besides, β-Mg17Al12 particles dynamically precipitated during deformation, acting as strong barrier against grain boundary migration through pinning effect. Through introduction of an interactive stress state, the RUE process promotes dispersion of the fiber texture that typically develops during the extrusion process. The key factor that promotes weakening of the fiber texture is derived from the refinement of basal orientated deformed grains, which form during upsetting deformation, into numerous non-basal orientated DRXed grains during early-stage extrusion. Compared with coarse deformed grains, these fine DRXed grains delay transformation of texture into the typical [10-10]–[11-20] fiber component. Grain refinement is implicated as the most significant factor with respect to simultaneous improvement of strength and toughness in the extruded rods, while tensile yield anisotropy in response to loading along the ED and TD is attributed to unDRXed grains with [10-10] fiber orientation. Compared to the as-cast state, extruded rods demonstrate increases in yield strength, ultimate tension strength, and elongation maximally up to ~2.6, ~2.2, and ~4.9 times, respectively. And when complete DRX structure is nearly achieved, the tensile yield anisotropy of extruded bar is effectively eliminated because the refined grains with relatively dispersed orientation inhibit the nucleation of tension twin and simultaneous enhance the Hall-Petch effect.

Effect of extrusion ratio on the microstructure and texture evolution of AZ31 magnesium alloy by the staggered extrusion (SE)

Improved microstructures of AZ31 magnesium alloy by semi-solid extrusion

Effect of grain size distribution and texture on the cold extrusion behavior and mechanical properties of AZ31 Mg alloy

A novel continues multi-shear extrusion process on the microstructure and mechanical property evolution of AZ31 magnesium alloys

Deformation behaviour, microstructure evolution and dynamic recrystallization mechanism of AZ31 magnesium alloy under co-extruded by Mg-Al composite billet

Role of Grain Refinement Mechanism on Microstructure and Performance in AZ31B Alloy During Interactive Alternating Forward Extrusion (AFE) Process

Microstructure and Properties of Magnesium Alloy Processed by a New Severe Plastic Deformation Method

Effect of Extrusion Deformation on Microstructures and Properties of AZ31 Magnesium Alloy

Effect of 90° route on microstructure of AZ31 magnesium alloy sheets by forging-bending repeated deformation

Influence of Extrusion Parameters on Grain Size and Texture Distributions of AZ31 Alloy

Effect of multi-pass continuous screw twist extrusion process on microstructure evolution, texture, and mechanical properties of AZ31 magnesium alloy

Effects of Extrusion–Shear Process Conditions on the Microstructures and Mechanical Properties of AZ31 Magnesium Alloy

Effects of Direct Extrusion Process on Microstructure, Texture Evolution and Yield Strength of Magnesium Alloy Az31

Microstructure and mechanical properties of AZ31 alloy prepared by cyclic expansion extrusion with asymmetrical extrusion cavity

Effects of extrusion ratio on the microstructure and mechanical properties of AZ31 Mg alloy

Effect of Stretch Bending on the Microstructure and Mechanical Properties of AZ31 Magnesium Alloy

Effects of Dynamic Recrystallization in Extruded and Compressed Az31 Magnesium Alloy

Microstructure, Texture and Mechanical Properties of AZ31 Magnesium Alloy Fabricated by High Strain Rate Biaxial Forging

The microstructure evolution, texture weakening mechanism and mechanical properties of AZ80 Mg alloy processed by repetitive upsetting-extrusion with reduced deformation temperature

Microstructure, Texture and Mechanical Properties of Extruded AZ31 Mg Alloy During Small Strain Multi-Directional Forging with Gradient Cooling

Microstructure Evolution of AZ Series Magnesium Alloys During Cyclic Extrusion Compression