Electrification of Heavy-Duty Construction Vehicles

Hong Wang,Yanjun Huang,Amir Khajepour,Chuan Hu

DOI: https://doi.org/10.2200/s00810ed1v01y201710aat001

2017-01-01

Synthesis Lectures on Advances in Automotive Technology

Abstract:The book begins with an introduction to electrification of heavy-duty vehicles and focuses on the interactions between track and blades with soil.

What problem does this paper attempt to address?

Design and Demonstration of a Dynamic Wireless Power Transfer System for Electric Vehicles.

Ze Zhou,Liyan Zhang,Zhitao Liu,Longhua Ma,Miao Huang,Hongye Su

DOI: https://doi.org/10.1007/s11432-018-9785-5

2019-01-01

Science China Information Sciences

Abstract:>The usage of electric vehicles is being globally promoted with the development of clean energy. However, the development of electric vehicles is limited by the battery capacity and the charging tech-
Opportunities and Challenges of Electrohydraulic Control Systems in the Electrification Era of Non-Road Mobile Machinery

Min CHENG,Jingbo HE,Hongyun MU,Xin YAN,Jun YANG,Jiahao OU,Ruqi DING,Junhui ZHANG,Bing Xu

DOI: https://doi.org/10.51393/j.jamst.2024001

2024-01-01

Journal of Advanced Manufacturing Science and Technology

Abstract:Electrification of Non-road mobile machinery (NRMM) is more and more urgent due to the demand of pollution reduction and energy conservation. In electrified NRMMs, electrohydraulic control system is still irreplaceable in many working conditions owing to its high power density and shock resistance performance. Meanwhile, electrohydraulic control systems are facing many opportunities to improve its energy efficiency by novel component and circuit design if the internal combustion engines (ICEs) and fossil fuel are replaced by electric motors (EMs) and energy storage devices. However, there are also a lot of challenges about controllability, compactness, lifetime and so on, due to the frequent variable load characteristic and wide speed regulation range of NRMMs. In this study, the technical opportunities and challenges of electrohydraulic control systems are reviewed and summarized in the electrification era of NRMM. Finally, the future directions are considered to improve the energy efficiency and electrification level of NRMMs.
Off-Road Construction and Agricultural Equipment Electrification: Review, Challenges, and Opportunities

Fuad Un-Noor,Guoyuan Wu,Harikishan Perugu,Sonya Collier,Seungju Yoon,Mathew Barth,Kanok Boriboonsomsin

DOI: https://doi.org/10.3390/vehicles4030044

2022-08-06

Vehicles

Abstract:Though the current wave of electric vehicles is transforming the on-road passenger and commercial vehicle fleets, similar attempts in the off-road equipment sector appear to be lacking. Because of the diverse equipment categories and varied applications, electrifying off-road equipment requires significant research and development. A successful electrification of such equipment can offer an array of benefits, including reduced air and noise pollution, higher energy efficiency, and increased productivity. This paper provides a review of the current state of technology in off-road equipment electrification, with a focus on the equipment used in construction and agricultural applications. The paper also discusses advantages of, and challenges associated with, electrifying off-road construction and agricultural equipment. In addition, potential solutions for overcoming these challenges as well as opportunities to facilitate the electrification of off-road construction and agricultural equipment are identified.
Prospects for purely electric construction machinery: Mechanical components, control strategies and typical machines

Xiaohui Huang,Wanbin Yan,Huajun Cao,Sujiao Chen,Guibao Tao,Jin Zhang

DOI: https://doi.org/10.1016/j.autcon.2024.105477

IF: 10.3

2024-05-19

Automation in Construction

Abstract:The electrification of construction machinery is an inevitable development trend due to strengthened restrictions on greenhouse gas and pollutant emissions from construction machinery. However, the widespread adoption of pure electric construction machinery is still in its infancy and faces numerous challenges. This paper introduces the latest significant contributions in the electrification of construction machinery, encompassing three dimensions: mechanical components, control strategies, and typical machines, and discusses the gaps and requirements of massive electrification in different dimensions. Lastly, the broad prospects and vast challenges of the widespread adoption of pure electric construction machinery are predicted and discussed. Additionally, the technical routes for the different type's construction machinery are analyzed, and the initiatives to promote electrification are put forward from the aspects of mechanical components, control strategies and application scenarios/business models.

construction & building technology,engineering, civil
Advanced Modeling, Analysis and Control for Electrified Vehicles

Xianjian Jin,Chongfeng Wei,Chao Huang,Chuan Hu,Guodong Yin,Mohammed Chadli

DOI: https://doi.org/10.3390/machines11090866

IF: 2.899

2023-01-01

Machines

Abstract:Electrified vehicles, especially fully driven electric ground vehicles, are expected to provide significantly increased traffic mobility and road utilization with faster response times, lower levels of fuel consumption, less environmental pollution, electrified power sources and actuators, and the benefits of greater driving safety and convenience integrated with diverse, dynamic subsystems [...]
Improving Wheel Loader Energy Efficiency with a Series Electric Hybrid Powertrain

Zichang Lin,Rui Wang,Bing Xu

DOI: https://doi.org/10.1115/fpmc2022-89099

2022-01-01

Abstract:Engine-powered wheel loaders are widely used in the construction field. However, it suffers from poor engine operation and low efficiency, showing great potential in energy saving and emission reduction. To improve the overall energy efficiency, a series electric hybrid wheel loader powertrain with decoupled main functions is proposed. The system includes a downsized engine, an electric generator, battery pack and three electric motor for drivetrain and lift/tilt hydraulic circuits. The drivetrain is electric motor driven and the lift/tilt functions are powered by electric load sensing system based on variable-speed control. Simulation study are carried out to provide an efficiency comparison between conventional and the proposed powertrain. A battery power-based energy strategy is developed for the hybrid wheel loader to check its potential on fuel saving. Results show that the electric hybrid system saves 43.6% of fuel consumption compared to conventional wheel loader. Energy efficiency comparison of subsystems and components between conventional and proposed powertrain is also presented.
Extending Battery Lifetime for Electric Wheel Loaders with Electric-Hydraulic Hybrid Powertrain

Haoxiang Zhang,Feng Wang,Bing Xu,Wieslaw Fiebig

DOI: https://doi.org/10.1016/j.energy.2022.125190

IF: 9

2022-01-01

Energy

Abstract:Electrification is the future trend for construction machinery due to its advantage of zero-carbon emission. The battery of electric construction machinery has an inevitable degradation phenomenon, which will increase the maintenance cost. In this paper a parallel electric-hydraulic hybrid powertrain is proposed to extend battery lifetime of an electric wheel loader by utilizing a hydraulic powertrain to provide and capture power during launch and braking. Different operation modes are analyzed and a rule-based energy management strategy is developed to determine the holding and switching conditions of each mode. Powertrains and battery aging models are introduced in detail and dynamic simulation is developed in Simulink. Results show that the parallel electric-hydraulic hybrid powertrain with the proposed strategy can reduce the battery full equivalent cycles, thereby achieving a 15.64% improvement in the battery lifetime compared with the pure electric powertrain. Moreover, influences of the strategy parameters on extending the battery lifetime are further discussed, which gives a parametric design guideline to the energy management strategy.
Terramechanics of Heavy-duty Construction Vehicle and Interactions Between Track and Blades with Soil

Hong Wang,Yanjun Huang,Amir Khajepour,Chuan Hu

DOI: https://doi.org/10.1007/978-3-031-01495-6_2

2018-01-01

Abstract:The external loads on bulldozers are the results of interactions between the track and blades with soil. This chapter discusses the mechanics regarding the interaction between the moving device/working part of the bulldozer, and the ground to improve the traction performance and operating efficiency of the bulldozer; and also provides the theoretical foundation for the subsequent driving dynamics analysis of the tracked bulldozer. The interaction forces are also needed in the dynamics and energy management of the electrified vehicle.
Energy Efficiency Improvement of Battery Powered Wheel Loader with an Electric-Hydrostatic Hybrid Powertrain

Qi Zhang,Feng Wang,Min Cheng,Bing Xu

DOI: https://doi.org/10.1177/09544070221076887

2022-01-01

Proceedings of the Institution of Mechanical Engineers Part D Journal of Automobile Engineering

Abstract:An electric-hydrostatic hybrid powertrain is proposed for the wheel loader propulsion system. The powertrain is constituted from an electric hydrostatic powertrain by adding a hydraulic accumulator as the second power source. It not only reduces energy consumption through regenerative braking, but also improves the power performance of the machine. A thermostat control strategy is developed for electric hydrostatic hybrid wheel loader and a speed-displacement compound control is developed for the electric hydrostatic wheel loader. The energy flow, losses analysis, and energy efficiency in the two powertrains are studied. The energy consumption reduction of the electric hydrostatic hybrid powertrain over the electric hydrostatic powertrain is identified in the wheel loader loading cycle. Results show the hydraulic accumulator in the hybrid powertrain increases the hydrostatic transmission efficiency and overall system efficiency. The energy efficiency in the electric hydrostatic powertrain is 45.64% and 51.66% in the electric hydrostatic hybrid powertrain. The total battery energy consumption is 14.20 kWh in the EH wheel loader and 12.48 kWh in the EH-hybrid wheel loader (50 cycles). The total energy consumption saving by using hybrid powertrain is 12.11%.
Electro-Hydrostatic Actuator System with Separate Design to Improve Efficiency for Working Function of Electric Wheel Loader

Yihan Qiao,Jiaming Wu,Feng Wang,Bing Xu

DOI: https://doi.org/10.1115/fpmc2024-141117

2024-01-01

Abstract:Abstract Powertrain electrification is an effective solution to reducing emissions of construction machinery. However, working function of current electric wheel loaders still employs electric motors paired with centralized load-sensing system. The system suffers from low energy efficiency because of valve throttling losses. The electro-hydrostatic actuator (EHA) emerges as an efficient way to enhance energy efficiency. The velocity of actuator is controlled by electric motor or pump directly, eliminating throttling losses from control valve. Therefore, a separate electro-hydrostatic actuator system is proposed for working function of electric wheel loader, to prevent additional load and utilize commercially available hydraulic components. Modeling and parameter design are conducted. A mode-based control strategy is developed. The simulation study is carried out to verify the feasibility of system and control strategy. The system performance and energy comparison between proposed system and centralized load-sensing baseline system are conducted. Results demonstrate the efficiency of proposed system improves from 37.6% to 71.9% compared to baseline system.
An Electric-Hydraulic Hybrid Wheel Loader with Mode-Driven Control Strategy

Zihan Wu,Feng Wang,Bing Xu,Wieslaw Fiebig

DOI: https://doi.org/10.1115/fpmc2022-90715

2022-01-01

Abstract:The powertrain electrification is an effective solution to emission reduction of mobile machines. To overcome the low power density of electric drive, a hydraulic accumulator is introduced as a supplementary power source. In this paper an electric-hydraulic hybrid powertrain solution is studied for wheel loader propulsion system, where it combines the energy density of electric drive and high power density of hydraulic drive. The energy management strategy is essential for hybrid powertrain since it determines how efficiently the power is transferred between different energy sources. In this paper a mode-driven control strategy for electric-hydraulic hybrid wheel loader is proposed to achieve electric power reduction over power follower strategy (baseline strategy), without sacrificing electric energy use and vehicle operation hours. In the strategy four modes are defined and the expected hydraulic SOC (system pressure) profile in each mode is scheduled to provide supplementary power assist and capture regenerative braking energy. By setting the pressure profile, the hydraulic charge sustaining is guaranteed. The system operation with mode-driven strategy is compared with power follower strategy through simulation studies. Results show that peak powers of battery and electric motor with mode-driven strategy are reduced by nearly 30% compared to power follower strategy. Results also show that the vehicle operation hour has been slightly increased by 3% by using mode-driven strategy. These results verify the effectiveness of proposed strategy for electric-hydraulic hybrid wheel loader.
Applications of Electrical Machine for Vehicle Driving System

E Yamada,ZM Zhao

DOI: https://doi.org/10.1109/ipemc.2000.883051

2000-01-01

Abstract:Vehicles powered by electric motors are represented by electric vehicles (EV) and hybrid electric vehicles (HEV). A method is presented for driving a vehicle using an electric motor. Permanent magnet synchronous motors have been more often used on the most advanced EVs and HEVs. This paper describes the background and the characteristics of permanent magnet synchronous motors for driving vehicles, and the prospects for future development
Battery Swapping: an Aggressive Approach to Transportation Electrification

Mingfei Ban,Juni Yu,Zhiyi Li,Danyang Guo,Jing Ge

DOI: https://doi.org/10.1109/mele.2019.2925762

2019-01-01

IEEE Electrification Magazine

Abstract:Transportation electrification is regarded as one of the most significant opportunities to address the social and environmental challenges posed by mass motorization and rapid urbanization. Electric vehicles (EVs) are playing an essential role in realizing transportation electrification, with benefits of oil conservation, local air-quality improvement, global climate change mitigation, and transit mode upgrading. In principle, EVs include battery electric vehicles and plug-in hybrid electric vehicles, with service types representing passenger vehicles, light-duty commercial vehicles, buses, and trucks. For brevity, EVs as referred to in this article are primarily passenger vehicles and light-duty commercial vehicles.
Charging Electric Vehicle Batteries: Wired and Wireless Power Transfer: Exploring EV charging technologies

Hua Bai,Yang Huang,D. Costinett,Ziwei Liang,Ruiyang Qin,Liyan Zhu,L. Tolbert

DOI: https://doi.org/10.1109/MPEL.2022.3173543

2022-06-01

IEEE Power Electronics Magazine

Abstract:Due to the environmental concerns about CO2-caused global warming, policymakers are pushing electrified vehicles (EVs) to reduce these emissions. For passenger vehicles only, the electrified fleet is forecasted to reach 80 million in the U.S. and 500 million globally by 2040. Key enablers for such rapid EV adoption include the improvement of battery energy density, lifespan and safety, and drastic cost reduction of batteries and power electronics. The technology of power electronics nowadays can be found in many aspects of EVs. It alters and transforms the energy from the power source to different forms to feed the loads. For example, the on-board charger (OBC) accepts ac input and converts it to high voltage (HV) dc to charge the propulsion battery. An auxiliary power module (APM) steps down the HV battery voltage to low voltage (LV) to charge the LV battery [1]. The HV dc bus voltage is converted to an ac form to drive the propulsion motor, forming the motor drive inverter. Putting the power electronics system and the batteries together, the typical structure of an EV is shown in Figure 1. In addition, power electronics can be found in other onboard auxiliary circuits, such as LED lighting and battery management system (BMS).

Environmental Science,Engineering
Influences of Electric Vehicles on Power System and Key Technologies of Vehicle-to-Grid

Canbing Li,Yijia Cao,Yonghong Kuang,Bin Zhou

DOI: https://doi.org/10.1007/978-3-662-49364-9

2016-01-01

Abstract:This book analyzes the influence of electric vehicles on microclimate and the indirect influence on power load from a unique perspective. It discusses different aspects of Vehicle-to-grid (V2G) techno
Research of Electric/Diesel Hybrid on Rail Heavy-duty Track Maintenance Machine

Jiacheng Xu

2015-01-01

Abstract:Dual-power sourced rail heavy-duty track maintenance machines were proposed against the defects of the current diesel engine and hydraulic-driven mode. The advantages and application range of the electric/diesel hybrid on rail heavy-duty track maintenance machine were analyzed, and the technical difficulties were described. Finally, a brief introduction of electric/diesel hybrid 48-stones rail grinding machine was provided.
Reducing Operation Emissions and Improving Work Efficiency Using a Pure Electric Wheel Drive Tractor

Chang-Kai Wen,Wen Ren,Qing-Zhen Zhu,Chun-Jiang Zhao,Zhen-Hao Luo,Sheng-Li Zhang,Bin Xie,Zhi-Jun Meng

DOI: https://doi.org/10.1016/j.eng.2024.01.026

IF: 12.834

2024-03-22

Engineering

Abstract:In response to the problems of excessive greenhouse-gas and particulate emissions and the low traction efficiency of conventional diesel tractors in the field, a purely electric wheel-side drive tractor was studied, including an electric motor drive system, a battery ballast system, and an electro-hydraulic suspension system. This paper develops a dynamics model of an electric tractor-ploughing unit under complex soil conditions, leading to the proposal of an active control method for drive wheel torque and a joint control method for the traction force of the suspension system and the front- and rear-axle loads of a tractor. Finally, the tractor is prototyped and assembled, and ploughing tests are carried out. The ploughing results show that the active torque-distribution control method proposed in this study reduces the tractor slip by 14.83% and increases the traction efficiency by 10.28% compared with the average torque-distribution mode. Compared with the conventional traction control mode, the joint control method for traction and ballast proposed in this paper results in a 3.7% increase in traction efficiency, a 15.05% decrease in slip, and a 4.9% reduction in total drive motor energy consumption. This study will help to improve the operation quality and traction efficiency of electric tractors in complex soil conditions.

engineering, multidisciplinary
Experiences and Applications of Electric and Plug-In Hybrid Vehicles in Power System Networks

Cagil Ozansoy,Taha Selim Ustun,Aladin Zayegh

DOI: https://doi.org/10.1007/978-3-319-43651-7_7

2016-12-31

Abstract:Transportation electrification is inevitable driven by rising energy costs, climate and emission control requirements, and availability of petroleum supplies. Even a realistic 10 % electrification of transportation is expected to impact the electricity generation, transmission, and distribution capacities, and hence the world economy. In this chapter, the authors seek to enlighten the reader on electric vehicle usage around the world by discussing their applications, electric vehicle trials, and key learnings from these trials across three continents: America, Europe, and Australia. Special emphasis has been given to discussing the commuting trends across the three continents and how that effects the transition into the electrification of transportation. The chapter continues with an impact analysis of electric vehicles on car users, the power quality of grids, and finally carbon emissions. Finally, examples of charging infrastructure and worldwide vehicle-to-grid applications are reviewed. The chapter concludes with a discussion on the need for interoperable communication standards, as an enabling technology for the management of the transactions between the grid and electric vehicles.
Electric Heavy Vehicle Transportation Highway (By Catenary System)

M.D. Patil,V.A. Vyawahare,Suyash Dhayarkar,Suraj Sontakke,Vipul Shinde,Nilam Ghuge

DOI: https://doi.org/10.1051/itmconf/20224401004

2022-05-05

ITM Web of Conferences

Abstract:Authors: M.D. Patil, V.A. Vyawahare, Suyash Dhayarkar, Suraj Sontakke, Vipul Shinde and Nilam Ghuge. ITM Web of Conferences Vol. 44 , page 01004 Published online: 05/05/2022
Improving productivity of a battery powered electric wheel loader with electric-hydraulic hybrid drive solution

Feng Wang,Qi Zhang,Qunya Wen,Bing Xu

DOI: https://doi.org/10.1016/j.jclepro.2024.140776

IF: 11.1

2024-02-01

Journal of Cleaner Production

Abstract:Powertrain electrification is one of the effective ways to improve energy efficiency and reduce emissions for off-road mobile machines. However, the batteries in the electric mobile machine always go through frequent and large power shocks, weakening the machine's productivity. To improve the productivity of the battery powered wheel loader, an electric-hydraulic hybrid parallel propulsion system solution is proposed. The hybrid powertrain is reconstructed from a battery powered electric powertrain by introducing a hydraulic pump-accumulator subsystem. The hydraulic powertrain is coupled to the electric powertrain in parallel providing strong power assistance and hydraulic energy recovery. A torque distribution energy management strategy is developed to manage the power flows of two energy sources. With the proposed hybrid powertrain, the productivity of the wheel loader is improved by up to 17.4%. The energy efficiency and carbon emissions are analyzed.

environmental sciences,green & sustainable science & technology,engineering, environmental

Electrification of Heavy-Duty Construction Vehicles

Design and Demonstration of a Dynamic Wireless Power Transfer System for Electric Vehicles.

Opportunities and Challenges of Electrohydraulic Control Systems in the Electrification Era of Non-Road Mobile Machinery

Off-Road Construction and Agricultural Equipment Electrification: Review, Challenges, and Opportunities

Prospects for purely electric construction machinery: Mechanical components, control strategies and typical machines

Advanced Modeling, Analysis and Control for Electrified Vehicles

Improving Wheel Loader Energy Efficiency with a Series Electric Hybrid Powertrain

Extending Battery Lifetime for Electric Wheel Loaders with Electric-Hydraulic Hybrid Powertrain

Terramechanics of Heavy-duty Construction Vehicle and Interactions Between Track and Blades with Soil

Energy Efficiency Improvement of Battery Powered Wheel Loader with an Electric-Hydrostatic Hybrid Powertrain

Electro-Hydrostatic Actuator System with Separate Design to Improve Efficiency for Working Function of Electric Wheel Loader

An Electric-Hydraulic Hybrid Wheel Loader with Mode-Driven Control Strategy

Applications of Electrical Machine for Vehicle Driving System

Battery Swapping: an Aggressive Approach to Transportation Electrification

Charging Electric Vehicle Batteries: Wired and Wireless Power Transfer: Exploring EV charging technologies

Influences of Electric Vehicles on Power System and Key Technologies of Vehicle-to-Grid

Research of Electric/Diesel Hybrid on Rail Heavy-duty Track Maintenance Machine

Reducing Operation Emissions and Improving Work Efficiency Using a Pure Electric Wheel Drive Tractor

Experiences and Applications of Electric and Plug-In Hybrid Vehicles in Power System Networks

Electric Heavy Vehicle Transportation Highway (By Catenary System)

Improving productivity of a battery powered electric wheel loader with electric-hydraulic hybrid drive solution