Abstract:Lithium-sulphur (Li-S) battery, with the high theoretical capacity density (~1675 mAh g-1) and energy density (~2600 Wh kg-1) as well as the easy access and non-toxic of raw materials, demonstrates a promising prospect among the high energy storage systems for electric vehicles (EVs) and portable electronic devices. However, several issues must be handled before its commercial application. Differing from traditional lithium-ion batteries, intermediate polysulfides generate and dissolve in the organic electrolyte during the discharge process of lithium-sulfur batteries. The dissolved polysulfides, shuttling between the cathode and anode, lower the utilization of sulfur. However, the dissolution of polysulfide in a lithium-sulfur battery is highly dependent on the sulfur/electrolyte loading. Thus an appropriate dosage of electrolyte will build a concentration gradient, which will limit the dissolution of polysfulfides. Herein, a lithium-sulfur cell with a high initial discharge capacity of 1053 mAh g-1 at a high rate of 1 C and an ultralow decay rate of 0.049 %/per cycle during 1000 cycles was obtained by using CNT-sulfur cathode and suppressing polysulfide shuttle to a shuttle factor of 0.02 by matching the sulfur/electrolyte loading[1]. Beyond the issue of polysulfide shuttle, Li-S battery is always with low practical energy density because sulfur has a low electrical conductivity (5×10-30 S cm-1 at 25 oC) and extra conductive network is highly required. Generally, the addition of conductive materials will neutralize the advantage in high energy density of Li-S battery. Herein, we employed CNTs to build the unblocked conductive skeleton and room-temperature, one-step ball-milling treatment of aligned CNTs and sulfur was applied to obtain high sulfur content of 90%. The 90% sulfur loading cathode exhibited a superior density of 1.98 g cm-3 (2.07 g cm-3 for sulfur), which greatly increases the volumetric energy density of lithium-sulfur battery[2]. To improve the areal density of sulfur in the cathode further, a 3D Al foam was employed as the long-range conductive matrix. The combination of 3D Al foam with CNT frameworks not only exhibits long-/short-range scaffolds as electron pathways through hierarchical point-line-plate contact, but also offers vast void space to accommodate huge amount of active materials and interconnected channels with short diffusion pathways and low resistance. A high sulfur loading of 7.0 mg cm-2 (based on the surface area of the electrode) was available with a discharge capacity of 6.02 mAh cm-2 (860 mAh g-1) at a current density of 1.17 mA cm-2 (167 mA g-1). Based on the total weight of the cell, a super high energy density of 367 Wh kg-1 was achieved, which is much higher than the cell with routine Al foil current collectors[3]. Reference [1]Cheng X-B, Huang J-Q, Peng H-J et al., Journal of Power Sources. 2014, 253: 263-268. [2]Cheng X-B, Huang J-Q, Zhang Q et al., Nano Energy, 2014, 4: 65–72. [3]Cheng X-B, Peng H-J, Huang J-Q et al., Journal of Power Sources. 2014, 261: 264-270.

A Nacre‐Like Carbon Nanotube Sheet for High Performance Li‐Polysulfide Batteries with High Sulfur Loading

A Freestanding Flexible Single‐Atom Cobalt‐Based Multifunctional Interlayer Toward Reversible and Durable Lithium‐Sulfur Batteries

Enhanced Adsorption of Polysulfides on Carbon Nanotubes/Boron Nitride Fibers for High-Performance Lithium-Sulfur Batteries

An Entangled Cobalt–Nitrogen–Carbon Nanotube Array Electrode with Synergetic Confinement and Electrocatalysis of Polysulfides for Stable Li–S Batteries

Ultrafine NbN Nanoparticle Decorated Nitrogen-Doped Carbon Nanosheets with Efficient Polysulfide Catalytic Conversion for Superior Li-S Batteries

Carbon Nanotube-Connected Yolk–Shell Carbon Nanopolyhedras with Cobalt and Nitrogen Doping As Sulfur Immobilizers for High-Performance Lithium–Sulfur Batteries

Efficient Polysulfide Barrier of a Graphene Aerogel–carbon Nanofibers–ni Network for High-Energy-density Lithium–sulfur Batteries with Ultrahigh Sulfur Content

Nitrogen Doped Carbon Nanosheets Encapsulated in Situ Generated Sulfur Enable High Capacity and Superior Rate Cathode for Li-S Batteries

Encapsulating Sulfur into Carbon Nanotube Framework for Robust Lithium-Sulfur Batteries

Lamellar MXene Composite Aerogels with Sandwiched Carbon Nanotubes Enable Stable Lithium–Sulfur Batteries with a High Sulfur Loading

Nitrogen-Doped Carbon Nanotube Forests Planted on Cobalt Nanoflowers As Polysulfide Mediator for Ultralow Self-Discharge and High Areal-Capacity Lithium-Sulfur Batteries.

Self-Templated Formation of Carbon Nanotubes Interpenetrating Ordered Microporous Carbon Nanospheres for High-Performance Li–S Batteries

Facilitation polysulfides adsorption/catalysis by nitrogen/phosphorous co-doped carbon nanofibers networks for advanced lithium/polysulfides batteries

Nitrogen‐Deficient Graphitic Carbon Nitride/Carbon Nanotube as Polysulfide Barrier of High‐Performance Lithium‐Sulfur Batteries

Nitrogen-Doped Hollow Carbon Polyhedrons With Carbon Nanotubes Surface Layers As Effective Sulfur Hosts For High-Rate, Long-Lifespan Lithium-Sulfur Batteries

Rational Fabrication of Nitrogen and Sulfur Codoped Carbon Nanotubes/MoS2 for High-Performance Lithium-Sulfur Batteries

A new defect-rich and ultrathin ZnCo layered double hydroxide/carbon nanotubes architecture to facilitate catalytic conversion of polysulfides for high-performance Li-S batteries

Polar and Conductive Iron Carbide@n-Doped Porous Carbon Nanosheets As a Sulfur Host for High Performance Lithium Sulfur Batteries

Promoting the Synergistic Effect of Sulfur Immobilization and Polysulfides Trapping by Nitrogen Functionalized Interconnected Hollow Carbon Nanocages for High-Performance Lithium–sulfur Batteries

Coupling highly dispersed Sb2S3 nanodots with nitrogen/sulfur dual-doped porous carbon nanosheets for efficient immobilization and catalysis of polysulfides conversion

Encapsulating Co9S8 nanocrystals into CNT-reinforced N-doped carbon nanofibers as a chainmail-like electrocatalyst for advanced Li-S batteries with high sulfur loading