Abstract:The rapid capacity decay of lithium–sulphur batteries has been a significant obstacle for practical application, which is generally considered to arise from dissolution of lithium polysulphide in the electrolyte and diffusion away from the cathode. As the lithium content in the polysuphide increases with further discharge, capacity decay occurs also from the passivating effects by the formation of insoluble sulphides, further amplified by volume increase. More recently, weakening of sulphur adhesion to carbon with progress in discharge is also an important factor in the sulphur cathode degradation. In order to overcome capacity decay caused by all the above mechanisms, we have prepared a composite cathode made of sulphur and high density carbon nanotube (HD-CNT) forest scaffold that is able to interfacially adsorb and volumetrically confine the polysulphide species and accommodate the expansion of sulphur discharge products effectively. This cathode demonstrates very high electrochemical stability and high discharge capacity up to 200 full discharge/charge cycles even with the use of the basic organic ether electrolyte where polysulphide shows high solubility, thus providing evidence for confinement and interfacial contact. Retention and surface adsorption favoured by minimizing the wall-to-wall distance between the aligned CNTs arise from a decrease in the reaction energy of the adsorption. Computational simulation of the interface between polysulphide species and carbon nanotube surface provides first-principle confirmation of improved binding between C and S in the polysulphides as wall-to-wall distance is decreased. The HD-CNT scaffold is self-binding and highly-conducting thus the conventional additives of binder and carbon black are also fully eliminated. A high discharge capacity of 812mAhg−1 of sulphur (corresponding to 503mAhg−1 of the whole cathode material mass) is stably retained after 200 cycles at 400mAg−1 with a small average capacity decay of only 0.054% per cycle on average These encouraging results provide novel approaches to designing and fabricating long cycle life cathode in a lithium–sulphur battery.

Enhanced Adsorption of Polysulfides on Carbon Nanotubes/Boron Nitride Fibers for High-Performance Lithium-Sulfur Batteries

A Nitrogen/Oxygen Dual-Doped Porous Carbon with High Catalytic Conversion Ability Toward Polysulfides for Advanced Lithium–Sulfur Batteries

Bimetallic Nanoparticles Decorated Porous Carbon As the Host Material to Enhance the Performance of Lithium-Sulfur Batteries

Bio-derived N-doped Porous Carbon As Sulfur Hosts for High Performance Lithium Sulfur Batteries

A Nacre‐Like Carbon Nanotube Sheet for High Performance Li‐Polysulfide Batteries with High Sulfur Loading

Single-atomic Co-B2N2 sites anchored on carbon nanotube arrays promote lithium polysulfide conversion in lithium-sulfur batteries

Strong Lithium Polysulfide Chemisorption on Electroactive Sites of Nitrogen-Doped Carbon Enables High-Performance Lithium-Sulfur Battery Cathodes

Nitrogen-doped nanotubes and few-layer montmorillonite composites as an effective polysulfides adsorbent for lithium–sulfur batteries

An Entangled Cobalt–Nitrogen–Carbon Nanotube Array Electrode with Synergetic Confinement and Electrocatalysis of Polysulfides for Stable Li–S Batteries

Strong Lithium Polysulfide Chemisorption on Electroactive Sites of Nitrogen‐Doped Carbon Composites for High‐Performance Lithium–Sulfur Battery Cathodes

Synergistic Adsorption-Catalytic Sites TiN/Ta2O5 with Multidimensional Carbon Structure to Enable High-Performance Li-S Batteries

Self-Templated Formation of Carbon Nanotubes Interpenetrating Ordered Microporous Carbon Nanospheres for High-Performance Li–S Batteries

Fabrication of NiFe-LDHs Modified Carbon Nanotubes as the High-Performance Sulfur Host for Lithium–Sulfur Batteries

Carbon Nanotube-Connected Yolk–Shell Carbon Nanopolyhedras with Cobalt and Nitrogen Doping As Sulfur Immobilizers for High-Performance Lithium–Sulfur Batteries

Facilitation polysulfides adsorption/catalysis by nitrogen/phosphorous co-doped carbon nanofibers networks for advanced lithium/polysulfides batteries

Nitrogen‐Deficient Graphitic Carbon Nitride/Carbon Nanotube as Polysulfide Barrier of High‐Performance Lithium‐Sulfur Batteries

Self-Templated Formation of Interlaced Carbon Nanotubes Threaded Hollow Co3S4 Nanoboxes for High-Rate and Heat-Resistant Lithium-Sulfur Batteries.

Flexible and Self-Supported Sulfur Cathode for High-Energy-Density Lithium-Sulfur Batteries

Soluble Polysulphide Sorption Using Carbon Nanotube Forest for Enhancing Cycle Performance in a Lithium–sulphur Battery

Coupling highly dispersed Sb2S3 nanodots with nitrogen/sulfur dual-doped porous carbon nanosheets for efficient immobilization and catalysis of polysulfides conversion

Synergistic restriction of polysulfides enabled by cobalt@carbon spheres embedded CNTs: A facile approach for constructing sulfur cathodes with high sulfur content