Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

Effects of Shear Rate on Cyclic Behavior of Dry Stack Masonry Joint

Experimental Study of RC Frames with Window and Door Openings Under Cyclic Loading

Experimental Study on Mechanical Properties of Basalt Fiber-Clay Lime Mortar and Application in Brick Masonry

Explicit Approach for the In-Plane Cyclic Behaviors of Unreinforced Masonry Structures Using Finite Particle Method

Evaluating the Role of Mortar Composition on the Cyclic Behavior of Unreinforced Masonry Shear Walls

Quasi-static, Cyclic Loading Tests of RAC Brick Masonry Walls Strengthened by Basalt Textile Reinforced Concrete

Influence of Internal Friction Angle and Interface Roughness on Shear Behavior of Mortar-Rock Binary Medium Joint

3D hybrid modelling approach combining the finite and discrete element methods: Validation based on masonry shear wall tests

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

Numerical analysis of the brick shape and bond pattern effects on the masonry cyclic behavior: a new brick shape to improve the masonry seismic performance

Investigating the confinement effects on masonry behavior based on friction interface

Study on the shear properties of masonry pagoda mortar and its influencing factors

Experimental investigation on shear strength deterioration at the interface between different rock types under cyclic loading

Comparative numerical study to simulate masonry with bed joint reinforced repointing

Seismic behavior of load-bearing horizontal-hole interlocking concrete block masonry walls: An experimental investigation of variable configurations

Experimental Research and Numerical Analysis of CFRP Retrofitted Masonry Triplets under Shear Loading

Tensile Fracture Mechanism of Masonry Wallettes Parallel to Bed Joints: A Stochastic Discontinuum Analysis

In-Plane Cyclic Behaviour Comparison of Adobe Wall Retrofitted by Mortar Enhanced by Physical and Chemical Methods

Study of dynamic behavior of concrete under splitting tensile tests based on mesomechanics

Stick–slip Behaviour of Mortar–rock Interface under High Loading Rate

In-Plane Strengthening Effect of Prefabricated Concrete Walls on Masonry Structures: Shaking Table Test