Abstract:Wake-up receivers (WuRXs) help to significantly reduce the average power of the Internet of the Things (loT) hardware systems. To lower the “asleep” power in the idle state, the WuRX structures based on non-standard protocols have been widely studied in prior researches, which can realize a high sensitivity [1] or low power [2]. Compared to the non-standard receivers, there are more design challenges in the standard-compliant WuRXs. For example, a BLE-compliant WuRX operating in the congested 2.4GHz band should be able to handle potentially large interferers including adjacent-channel tone and image, as well as realize a high sensitivity for long-reach access. Therefore, there have been several conventional solutions for the interference-resilient BLE-compliant WuRXs: 1) Single-path down-conversion WuRXs. The interference is handled by an RF filter [3] or a low-noise LO [4] (Fig. 1, top). The WuRX in [3] utilized an FBAR filter to reject the interference from the adjacent channel, resulting in a signal-to-interference ratio (SIR) of −6dB@2MHz, where the loss of FBAR filter degraded the sensitivity to −85dBm. An LC oscillator based LO was adopted in [4] to suppress the adjacent-channel interference by −10dB, but it's at the penalty of 1.2mW power. 2) I/Q-path down-conversion WuRXs. A Hartley WuRX was designed in [5] to reject both 2MHz adjacent-channel interference and image (Fig. 1, middle), as well as improve the sensitivity to −92dBm, while the I/Q downconverters and LO generators dominated the total power consumption. Although the WuRX power was reduced to 352μW by the edge combiner based I/O LO generation, the SIR was limited to −12.5dB due to the spurs and noise accompanying the LO signal. As a result, it's difficult for the conventional WuRX structures to realize both a high SIR and low power consumption.

A Low-Power OFDM-Based Wake-Up Mechanism for IoE Applications

Low power high data rate GHz range receiver in 40nm CMOS technology

DFT-s-OFDM-based On-Off Keying for Low-Power Wake-Up Signal

Receiver Design for Realizing On-Demand WiFi Wake-up using WLAN Signals

Analytical and Experimental Performance Analysis of Enhanced Wake-Up Receivers Based on Low-Power Base-Band Amplifiers

Design of a Low Power 60ghz OOK Receiver in 65nm CMOS Technology

An Interference-Resilient 120-Degree-apart Pseudo-I/Q BLE-Compliant Wake-Up Receiver Achieving-21dB SIR,-94dBm Sensitivity, and 4-D Wake-Up Signature

A 60ghz BiCMOS Self-Demodulator with Injection Locked Oscillator

Towards Ultra-Low Power OFDMA Downlink Demodulation.

Energy-Efficient Scheme For Ieee 802.15.4 Compliant Device

A 55 μ W 2.4 GHz wake-up receiver with offset-based peak detection achieving −90dBm sensitivity for IoT applications

Analysis and Design of a Multi-Mode Wake-Up Receiver Based on Direct Envelope Detection in Wireless Sensor Networks

Ultra-Low-Power IoT Communications: A novel address decoding approach for wake-up receivers

A 55uW 2.4GHz wake-up receiver with offset-based peak detection achieving −90dBm sensitivity for IoT applications

Low-Power, High-Data Rate 915 MHz Transceiver with Fully Passive Wake-Up Receiver for Biomedical Implants

An Improved Wake-Up Receiver Based on the Optimization of Low-Frequency Pattern Matchers

Energy and spectrum efficient wireless LAN by tightly integrating low-power wake-up radio

Enabling Low-Power OFDM for IoT by Exploiting Asymmetric Clock Rates

A 107 pJ/b TX 260 pJ/b RX Ultralow-Power MEMS-Based Transceiver With Wake-Up in ISM-Bands for IoT Applications

A Software-Defined Always-On System With 57-75-nW Wake-Up Function Using Asynchronous Clock-Free Pipelined Event-Driven Architecture and Time-Shielding Level-Crossing ADC