Abstract:Introduction The future of the international accord on mitigating the impact of climate change is linked to the successful commercialisation and implementation of renewable energy technologies. The latter is strongly dependent on finding commercially viable methods for successful dimensional nano-functionalization of the ceramic materials utilized in the fabrication of various energy devices either in energy generation (fuel cells) or storage (batteries, supercapacitors). Inkjet printing digital methods combining scalability and low equipment cost with high-resolution patterning can be a feasible solution for some of the shortcommings of the conventional fabrication technologies. 3D functionalization - Composite solid oxide fuel cells LSCF/CGO cathodes were nano-engineered via “dual” inkjet printing infiltration. The nano-decorated microstructure was found to extend the active three-phase boundary and to promote adsorbtion – dissociation - surface exchange reactions. Composite La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ /Ce 0.9 Gd 0.1 O 1.9 cathodes were subjected to “dual” inkjet printing infiltration of nitrate salt solutions in a single step procedure. After calcination in air at 700 o C the cathodes were decorated with Ce 0.9 Gd 0.1 O 1.9 and Co x O y nano particles. The effects of as created nano-decoration on the electrochemical activity and the performance stabilty in the intermediate temperature range (500-700 o C) were investigated. The infiltration was found to extend the active three-phase boundary and to promote adsorbtion-dissociation- surface exchange reactions. Electrochemical impedance tests conducted on symmetrical cells showed a reduction in the polarisation resistance of between 1.5 and 7.0 times depending on temperature (500-700 o C). The nano-decoration led to substantially enhanced stability (0.7 Ω•cm 2 at 550 o C after 100 hours of aging for CGO:Co x O y infiltration). As the composite LSCF/CGO cathodes had already percolating ionic and electronic networks, a low level loading of nanoparticles was sufficient to lead to an efficient short-range extension of the TPB and the density of ORR reaction sites. The sequence of infiltration was shown to influence the efficiency of the ORR promotion. Co x O y :CGO infiltration expanded the available surface area and promoted the catalytical activity towards ORR reaction. The superior effect of CGO:Co x O y infiltration was assigned to the introduction of additional promotion mechanisms (see Fig. 1) resulting in better electrochemical performance at lower temperatures (<650 o C). Both infiltrations suppressed the Sr surface segregation but only CGO:Co x O y infiltrated cathodes showed substantially improved stability after 100 hours of aging. Scaling up - Single step inkjet printing infiltration with doped ceria Ce 0.9 Ye 0.1 O 1.95 (YDC) and cobalt oxide (Co x O y ) precursor inks was performed in order scale-up the modification of the doped ceria interlayer in commercial (50x50x1 mm size) anode supported SOFCs. The penetration of the inks through the mono-phase La 0.8 Sr 0.2 Co 0.5 Fe 0.5 O 3-δ porous cathode to the Gd 0.1 Ce 0.9 O 2 interlayer was achieved by optimization of inks rheology jetting parameters. The low temperature calcination resulted in densification of the Gd-doped ceria porous interlayer as well as decoration of the cathode scaffold with nano-particles (~ 20-50 nm in size). The I-V testing in pure hydrogen showed maximum power density gain of 20% at 700 o C and 97% at 800 o C for the infiltrated cells (see Fig. 1). The effect was largely assigned to the improvement in the interfacial Ohmic resistance. The EIS study of the polarization losses of the reference and the infiltrated cells revealed reduction in the activation and concentration polarizations losses at 700 o C due to the nano-decoration of the La 0.8 Sr 0.2 Co 0.5 Fe 0.5 O 3-δ scaffold surface. Such effect was not clearly detectable at 800 o C where the drop of Ohmic losses was dominant. This work demonstrated that single-step inkjet printing infiltration, a non-disruptive low-cost technique, could produce significant and scalable performance enhancements in commercial SOFCs. Figure 1

The Fabrication of Inkjet-3D-Printed NiO–Ce0.8Gd0.2O2-Based Anode for a Solid-Oxide Fuel Cell and Study of Its Microstructure

Electrical Properties and Microstructure of 3D Printed Anodes Based on the Ni/Ce0.8Gd0.2O2 Composite for Solid Oxide Fuel Cells

The Effect of the Pore Former Nature on the Microstructure of Solid-Oxide-Fuel-Cell NiO- and 10YSZ-Based Anodes Formed by Hybrid 3D-Printing

An Anode-Supported Solid Oxide Fuel Cell (SOFC) Half-Cell Fabricated by Hybrid 3D Inkjet Printing and Laser Treatment

Nanofiber-based La 0.4 Sr 0.6 TiO 3 -Gd 0.2 Ce 0.8 O 1.9 -Ni composite anode for solid oxide fuel cells

Solid Oxide Fuel Cells with 3D Inkjet Printing Modified LSM-YSZ Interface

Vat Photopolymerization 3D Printing of NiO-YSZ Anode for Solid Oxide Fuel Cells

Facile preparation of patterned anode substrate for solid oxide fuel cells by direct-writing 3D printing technology

A high-performance planar anode-supported solid oxide fuel cell with hierarchical porous structure through slurry-based three-dimensional printing

Fabrication and Characterization of a Composite Ni-SDC Fuel Cell Cathode Reinforced by Ni Foam

Synthesis and Characterisation of Nanocrystalline CoxFe1-xGDC Powders as a Functional Anode Material for the Solid Oxide Fuel Cell

Nano-Functionalization of SOFC Electrodes Via Inkjet Printing

Gel-cast NiO–SDC Composites As Anodes for Solid Oxide Fuel Cells

The Impact of NiO on Microstructure and Electrical Property of Solid Oxide Fuel Cell Anode

Fabrication and Electrochemical Characterizations of Nd2NiO4+δ-Ce0.8Gd0.2O2−δ Composite Cathodes for Anode-Supported Intermediate Temperature Solid Oxide Fuel Cells

Liquid Plasma-Sprayed Nanonetwork La0.4Sr0.6Co0.2Fe0.8O3/Ce0.8Gd0.2O2 Composite Cathodes for Intermediate-Temperature Solid Oxide Fuel Cells

Synthesis of ((CeO2)0.8(Sm2O3)0.2)@NiO Core-Shell Type Nanostructures and Microextrusion Printing of a Composite Anode Based on Them

Nano-Structured Anodes of Solid Oxide Fuel Cells

Ni/SDC Materials for Solid Oxide Fuel Cell Anode Applications by the Glycine-Nitrate Method

Application of Yttria Stabilized Zirconia (8YSZ) and NiO Precursors for Fabrication of Composite Material for Anode-Supported SOFCs

Fabrication and Characterization of a Small Tubular Solid Oxide Fuel Cell with the La0.43Ca0.37Ni0.06Ti0.94O3-γ Anode